This standard specifies the requirements, test methods and inspection rules, marking, packaging, transportation and storage of rubber-surfaced anti-smash safety boots. This standard applies to rubber-surfaced anti-smash safety boots worn in waterproof places to protect the toes from injury. HG 3081-1999 Rubber-surfaced anti-smash safety boots HG3081-1999 Standard download decompression password: www.bzxz.net

IS 61. 050
Y 75: Y 78
Chemical Industry Standard of the People's Republic of China
(1999)
Issued on April 20, 1999
Implemented on April 1, 20000
National Bureau of Petrochemical Industry
Ts13. 340. 10
Preparation No.·2762999
HG3081-1999
This standard adopts Japanese industry standard TIST8U2 for safety improvement. 3. For the enterprise with G/T33911 rubber surface marked in the chemical industry, this standard is different from H:/T3081-1986 in terms of technical differences: addition of scope, referenced standards, etc.
The technical requirements and inspection rules for internal and external cooling are written in the text of the standard, and the ground, external cooling and boot thickness are assessed.
The physical mechanical properties such as tension, location, wear and radiation intensity are standardized, and the direct index of spraying degree is cancelled.
The quality assessment of the standard is revised into an assessment content. "An inspection rule has been added to the safety performance of the equipment. The standard was issued in 1986 and was put forward by the Technical Supervision Department of the former Ministry of Chemical Industry of the People's Republic of China. This standard is under the jurisdiction of the National Rubber and Rubber Products Standardization Technical Committee. The drafting unit of this standard is: 1 Shanghai Rubber Research Institute. The drafter of this standard is the company.
This standard was first issued as a national standard in 195, and in 2003 it was a recommended chemical industry standard and abbreviated as a national standard.
Chemical Industry Standard of the People's Republic of China
Sanash-proof rubler Rafely bootsHG 3081-1999
買ca—
This standard specifies the requirements, test methods and inspection rules for cavity and anti-melting safety boots, marking, packaging, transportation, etc. The standard is suitable for cavity and anti-melting safety boots worn by people who are not allowed to wear them. ? Cited standards
The clauses contained in the following standards constitute non-standard clauses through reference in this standard. This standard is published and the versions shown are valid. All standards will be subscribed by you. All parties to this standard should consult the latest version of the following standards. GR/T528--92 Determination of the properties of chemical adhesives GB/T532—1997 Determination of the adhesion strength of chemical adhesives to fabrics (id1ISO36119S3) K1539-82 (5S) Determination of the properties of chemical adhesives (using Akron grinding machine) GB 41—
Standard source of ignition conditioning test for plastic specimens, temperature, explosion and time (eQV1s047111983) HG/T2198-91
General requirements for physical test methods for chemical rubber HG/1240392 Inspection rules, markings, packaging, transportation and storage for cavity shoes IIG/T2873—1867 Test method for bending and lifting of rubber butterfly soles 3 Requirements
3.1 Inner headstock
3.1.1 Dimensions As shown in Figure 1, the horizontal distance from the front end of the inner headstock to the back is 4°-50mm, the height b is more than 30mm, and the bottom edge is horizontally curved. The width of the edge is 3~6mm. Inner headstock dimensions
3.1.2 The surface is smooth, the edge angle is normal, and the product should be protected from damage. 3.3 Resistance to corrosion, 4 impact resistance should comply with the provisions of Table 2, approved by the State Petroleum and Chemical Industry Bureau on April 20, 1999 and implemented on April 1, 2000. 3.2 External washing and surface resistance 3.2.1 The outer sole should have a relatively good anti-brush performance, anti-impact performance, impact resistance 3.2.2 The thickness of the outer sole and the upper must comply with the provisions of Table 2, as shown in the following table? External corrosion and surface resistance 3.2.3 The distance between each part is as shown in the figure, and the outer part can be high after the gold is added. 3.3.1 The surface of the inner toe cap should be tightly attached to the rubber surface. The cap must be placed in the inner toe cap. Only when the inner toe cap is made can it be removed. 3.3. The overall weight of the toe cap should be more than 2 kilograms. 3.4 The mechanical properties and tensile properties should meet the requirements of Table 3. The physical properties should meet the requirements of Table 3. The tensile strength is MPa. 5
JG external welcome
HG3081-1995
Development of physical fatigue performance of complete shoes
3.6.1 All parts must be in good condition, such as: the inner sole fabric is not more than 6c2mm, the length of the part is not shorter than 493mm, the outer bottom opening depth is not more than 3mm, the outer bottom depth is not more than 36.2 The surface is basically flat, bright, without any obvious spots: no other stains, no obvious spots ... 6
No gradual oiling is allowed, and the depth of the side oiling system shall not exceed 40 ml. 3. 6.7
There shall be no strong damage to the learning. Also cracks, rats, air, light, people and objects and their sweeping must fall: the height difference of the same double height is greater than 5m:
Small test method
4.7 trillion
1. 1. 1 The pressure test machine used in the test of this instrument
is estimated. The minimum value is below 3, and the test period is not more than 19. The test is about 100 mn, and the upper and lower platforms are parallel. 4. 1.2 Sample
Extend the inner head of the product to the final layer by 25mm ± 3m. Take the remaining part as the test example, as shown in Figure 3,
The inner core depth
The diameter of the inner head of the sample is 22mn. The height should be calculated by the mud figure. Then put the sample in the center of the pressure test, and add 4V machine within 3~5min. The pressure can be quickly increased to 4000, and the height is specified.
4.2 Way out
4.2.1 External impact inspection of installed pipe
Comprehensive technical points:||t t||External impact test
impact will be prepared by the national
standard. bZxz.net
4.2.3 Test method
Bitesheng
National fixed device
Figure 4 Impact test equipment
Test Kaihe chain quality single g Shi).2 Set the sample at the fixed time, and then make it descend from the mountain, and perform the impact test type test quality, take the rubber filter to measure its height 4.3 Immersion test
As shown in the figure. Put the whole boots with the table depth of 1/2 in water, and the effect of Ning is uniform, and the leather is full of air, and then forcefully non-risk air, if there are small bubbles, peel out the collection 4.4 Reverse test
Hc 3081-1999
Figure 5 Waterless test
First, place the inner head of the steel in a saline solution with a wave density of 1, and then wash off the attached salt in a concentrated low humidity zone at room temperature. The brain will be bright if the phenomenon is 4.5 The physical and mechanical properties of the rubber are tested in accordance with the provisions of HG298.
4.6 The test humidity of the rubber test piece is restored. The relative humidity and relative humidity are determined indirectly.
4. The determination of the properties of the new chemical control rubber is carried out in accordance with the provisions of HG298.
4.8 The determination of the properties of the vulcanized rubber during heating is carried out in accordance with the provisions of HG298.
4.9 The precision limit point should be determined.
I H! 532 fixed length,
2.10 acquisition of performance of the bottom improvement
due to HG283 determined implementation:
5 according to inspection rules
5.1 the physical length of the batch of shoes outside the region compensation for the residual quality inspection according to the provisions of HG/12404 hot implementation 5.2 the development of shoes performance control inspection and Baotou enterprise safety ship release must be completed according to Table 4 and Table 5: Table. Chengfa full performance rush
control return item
Chengheng vice
joint will quality main business
inspection change attack
internal package meaning supplement memory although offer
6 mark, packaging. Avoid salary. Storage
3081-1999
I have internal package head safety performance inspection
check change level
qualified two book level
6.1 According to the relevant provisions of H/2413 on rubber shoes, the packaging of the shoes shall be marked with the product number. 6.2 Each batch of rubber shoes shall have a certificate of conformity issued by the labor inspection department.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.