This standard specifies the scope of application, terms and definitions, classification and marking, technical requirements, test methods, inspection rules, marking and labeling, and product packaging, transportation and storage of the glue powder polystyrene particle external wall insulation system. This standard applies to the building external wall insulation system with glue powder polystyrene particle insulation slurry as the insulation layer, anti-crack mortar composite alkali-resistant glass fiber mesh cloth or hot-dip galvanized welded wire mesh as the anti-crack protective layer, and paint or facing bricks as the finishing layer. JG 158-2004 Glue powder polystyrene particle external wall insulation system JG158-2004 standard download decompression password: www.bzxz.net

tCS 91. 122. 60
Construction Industry Standard of the People's Republic of China JG158--2004
External thermal insulation rendering systems made of morlar withmineral linder and using cxpandled polystyrcae granule as aggregale2004-08-18Released
Ministry of Construction of the People's Republic of China
2004-12-01Implementation
Heat reference documents
Terms and definitions
Classification and!
Verification method
8 Marking buckle you
Other installation, construction and storage
A standard
Appendix Normative Appendix》
Appendix C (Normative record
Appendix [Appendix
List (Normative pool parts appendix)
Appendix F (Normative location appendix)
Appendix requirements (Normative appendix)
Appendix H (heat pool parts)
Normative appendix)
System durability test method
System water absorption test method
System flow sheet wind load energy comparison monitoring method
System impermeability test method
System porcelain village commercial tree test method
System dyeing tensile strength test method
System resistance performance test method||t t||Fire reactivity test method
Brick and whole material water reactivity test method
6153—2014
JG158—2004
This standard is in accordance with B112 standardization work guideline Part 1: Standard structure and GH1.1 standardization work guideline Part 2: Determination of heat protection performance of the team This standard is not equivalent to D1N18555 Part 1 of the South China Operation Guide. Polyethylene foam plastic (EPS) particles will be used in the insulation system. According to my country's national conditions, the technical characteristics of some components and enhancements are used in the test method. This standard adopts EOETAGCC1 European Technical Certification Guide for External Thermal Insulation Systems with a decorative layer. [MAJ01 .R6 Standard test method for deformation impact of external insulation and decoration system. HJMA105.01 Standard test method for deformation impact of external insulation and decoration system of glass fiber tape, ASM1>68-193 Standard test method for wear resistance under washing layer 3.
This standard is a mandatory clause.
This standard also includes the appendix A, appendix B, appendix C, appendix D, appendix E, appendix I, and appendix II. This standard is proposed by the Institute for the maintenance of the standard. This standard is under the jurisdiction of the Technical Committee of the Ministry of Construction of the People's Republic of China. The responsible unit of this standard: Beijing Standardization Technology Co., Ltd. China Building Standard Design Institute. The competent unit: Science and Technology Development Center of the Ministry of Construction, Beijing Zhonghengyue New Technology Development Center, China Building Science and Technology Institute of Physics, China Academy of Building Materials Engineering Institute, National Development and Reform Commission National Education Project Review Center, Beijing Construction Engineering Co., Ltd., Sichuan Mindian Tree Chemical (1 Hai) Co., Ltd., Xinding Building Standard Design Office, Tianjin Construction Standard Design Office, Lunan Wall Improvement Office, Beijing Yueping District Construction Committee, Beijing Fifth Construction Engineering Company, Beijing No. 1 Construction Engineering Company Beijing Zhuzong Group Jiayi Branch
The ten main people in this annotation are: Huang Zhenli, Xiaoming, Dun Siwei, Fang Zhanli, Ma Jinqiu, Ke Shaodan, Li Dongjie, [Qingmi Fangcezhi, Zhang Zhengchen Ban, Xia Shuhui, Ben Dongyi, Zuo, Du Hongjue, Chen Danlin, Song Xiaopu, Rao Paiguo, Yi Quanliang, Ke Yancheng, He Xiaolan, Xin Zhonglan, Wang Binghai. Qiu Lifang, Yang Zengzun, Liu Tangyan, Nai Cai. This annotation is published for the first time, and it was implemented in 2001. 1 Scope
Glue powder poly granule external wall insulation system
IG158-2CC4
This standard defines the terminology, definitions, sub-committee marking, technical requirements, methods, inspection, marking and labeling of the product packaging, transportation and storage: This standard is used for the building structure external wall insulation system with glue powder poly granule insulation slurry, fire retardant insulation layer, anti-cracking yarn slurry, flame retardant red mesh cloth, heat-sensitive zinc welded mesh as anti-cracking protection, and coating as the surface layer. 2 Normative references
The following documents have become the specifications of this standard through reference in this standard. All referenced documents with a specified date are not included in all subsequent revisions or revisions! This standard, however, encourages the parties who have agreed to this standard to study the new version of the document to be recognized as a reliable new version of this website. All documents without a date are applicable to this standard. GB821S5 filter stain ten long-term material energy and durability test square head G1751999 acid salt water mixture, ordinary toe acid salt water type B/T13162001 non-standard rental water, avoidance time, qualitative inspection method GT/T172K-197% continuous film, putty under film drying time determination method (H17:3-1979 putty flexibility determination method 13/T279 ··199 political adhesive non-volatile matter content determination CB3186 material product selection
GB/T 3310.1—P
Network ceramic tile test Part 1 Sampling and acceptance conditions dt [S010341: 1995, GB/T10.21999
GB/T3810.11999
(JS) 1c515-3: [995)
Porcelain test methods Part 2: Inspection of surface quality ([S] 10545-2: Test methods for ceramic tiles Part 3: Determination of water content, apparent porosity, apparent relative density and capacity GH/T3310.12 1S6S
Ceramic test methods Part 12: Determination of resistance to road use (Rl1S) 1 (1545-12: 1995) GH/21.1~4100.41999 GB768.3-1 Test methods for woven fabrics of reinforced materials Part 3: Determination of tensile strength and elongation at break of glass fibers
GB/T7697 Test methods for glass fibers
GR/THG25-1S88 Test methods for woven fabrics of reinforced materials Part 3: Determination of tensile strength and elongation at break of glass fibers
GB/T7697 Test methods for glass fibers
GR/THG25-1S88 Material flame retardancy test method GH/9195 Classification and specification of ceramics and sanitary ceramics GB79-1988 Test method for glazed glass bottles
U15/D!14.2-2CC1 Test method for reinforced tape products Part 2 Determination of the content of glass fiber flammable materials GBT9914.32C01 Test method for reinforced products Part 3: Determination of unit mass GT102-1S Determination of steady-state thermal insulation and related durability of thermal insulation materials, namely the heat plate method H10299-178 Test method for water resistance of insurance materials CB/T1677-1V? Test method for waterproof polyester materials for buildings 158—2004
GB/T171-1997 Test method for water vapor permeability of building materials ...JC/T171-1997 Test method for water vapor permeability of building materials
JC/T171-1997 Test method for water vapor permeability of building materials
|tt||JC/T547—1994 Ceramic wall and floor tile bite adhesive TC4I Naicheng Slope Ball
1999 Attached ball glass fiber same grid cloth
JC/T:841
JG/T24
Combined resin emulsion sand wall building dye
JG512CC2 Light aggregate cement technical specification
TJ52—1S52
2 Standard and inspection method for basic raw materials for general cement JGJ 70—1990
Building sand test method
199 Jin building resistance test method specification
Standard for test of bonding strength after surface treatment J:149—2UG3
IG/T :57—204
Building exterior wall board
1998 Pure load indoor board
JG/T3943
QB/T38971999 Electrified zinc grid
3 Terms and definitions
The following terms and definitions apply to this standard. 3.1
External insulation system made or mortar with minerat hinder and ostng expaaded polystyrene granule as aggregate (ETIRS)
It is a control system arranged on the outside of the outer block and consists of an interface layer, an anti-crack protective layer and a finishing layer, which plays the role of heat control, protection and installation.
Substructure: Substructure in the building that plays the role of bearing or protection. 3.3
Interface mortarLnlerlacetrealingagent is a mortar made by mixing an interface agent prepared by a high molecular weight polymer emulsion and an agent with cement and medium sand in a certain proportion. 3. 4
Mincral Hinder and Expanded Palystyrene Granule Insulating Nerial Material and Colored Apple granules are composed of a large number of aggregate particles with a forest area ratio of not less than ten grades of thermal insulation slurry 3.5
Rubber powder mineral htnder
Inorganic cementitious material is made in the factory by dry mixing technology and is specially used for preparing rubber tree polystyrene granule insulation 2
Slurry
Energy-saving granules expanded polystyrene granule JG158—2004
Mountain energy 7 olefin foam plastics are crushed and combined to make a Fixed particle base. A special material for preparing dry adhesive bonding particles with warm slurry.
Anti-crack sand finishing coat mortar
In the bonding emulsion, add more anti-cracking agents and anti-cracking substances to prepare cement, and mix with silica cement according to a certain proportion of sand. It has a certain degree of complexity: 3.8
Resistant to heat and alkali coated glass fiber elastic mesh cloth (hereinafter referred to as alkali mesh cloth) alkaliTesistantfihreglashmerh is a mesh cloth woven from alkali-resistant fibers, and the surface is coated with a high degree of resistant coating. The mesh cloth is made of water-resistant coating, 3.9
Polymer emulsion elastic base material (hereinafter referred to as elastic coating) lasticaraundcnating made of European water 3.10
Anti-crack flexible water-resistant putty (abbreviated as flexible water-resistant putty) waterprnnfflexihlepltty Putty with certain softness and water resistance made of elastic emulsion, agent and powder, etc. 3.11
Plastic braided bolt mecheanfralfixfngs
It is composed of screws (plastic nails or plastic nails with corrosion resistance) and plastic expansion disks. It is used to fix the hot-dip shovel net to the base wall. 3.12
Brick bonding mortar AllaexiveTartilke composite emulsion and admixtures are used to improve the strength of the surface / 42. The bonding mortar is made by mixing salt water with building brick sand (grade 3) according to a certain quality ratio and mixing. 3.13
Mixed with cement or other materials, various fillers and additives, it is a two-ply ceramic wall material. 4 Classification and marking
4.1 Classification
Powder-coated granular external insulation system is divided into two types: <Type powder-coated granular external insulation system is used for the screen surface of the adhesive granular external insulation system, the basic surface should be used 1:
One-to-one adhesive number case non-insulation needs to be used for the positive surface of the adhesive is mostly based on the silicone insulation system, the real use of the belt inspection method see Table 2.
JG: 1582CC4
very medical Rui body
concrete Rui and
kind of Niu Yi Pei
layer wall
Runyuan 1 blocking and
each and to Jia Pei
4.2 mark
another full meeting
different surface slurry
interface sand
table 1 coating finishing glue powder multiplication leather grain external protection system basic structural material finishing flour system fee positive grain external protection period anti basic quick construction protection
Collection system pre-
and moisturizing material
pull teaching belt protection certificate
anti-staining sand inspection
time deep plastic glass Peiwei two grid cloth
and other noodle shops
Chen Zaoqian water brain
plus type increase slip a change such as strong mesh cloth
high score lower milk elastic feeling layer polyester material
table 2 surface finishing glue powder poly Lai topic particle external insulation system medical basic control positive brick finishing anti powder poly Hui Yang industry fiber protection system flow Philippine structure road system variable guard| |tt||Anti-insulation material
Di Jian Bozhi mortar
Yineng zinc welded wire mesh
(Use for purchasing and quality layer paving)
Second color broken material
The mark of amine powder particle insulation ticket is composed of code and loss shape: ETIRS
Uniform surface sinking
Adhesive moisture
Surface transfer + material:
Cross powder channel measurement particle insulation ticket system code
4. 3 Marking and indicating
Example 1: EIIRS-core coating screen surface glue powder case benzene title particle external insulation system 5: Requirements
5.1 Glue powder rate benzene particle external insulation system
Structure indicating agent
Min Tong indicating page figure
5.1.1 The external insulation system shall be verified by large-scale weather resistance test: For the carbon surface facing external insulation system, it is also necessary to undergo anti-weathering test verification and ensure that the brick facing and external insulation system will not fall off under the design intensity level. 4
The performance of the glue powder compact single particle external insulation system meets the requirements of the table, 5.1.2
Table 3 Performance index of the glue powder external insulation system
Water absorption/(/m)Flooding 1
Impact flow pressure
Wind resistance
Water vapor dead retention/r/(n·2)
Small water absorption
Time separation. 5.
Tension strength (t/MP
Your surface drilling/electrical/MF
(now good mu shaking
Fire should be bottom
5.2 Interface mortar
And the reverse slurry performance meets the requirements of Table 1,
Isoglucose acid slurry
Shear bonding shop
5.3 Glue powderbzxZ.net
Performance bracket|| tt||JG158—2334
After consulting water 1 ring heat (0 cold allow
20 core active ring shall not be opened, no-load into the fall, dynamic type protective layer and medical layer of the pull of the middle of the small plate small under 0.3MP9. The damage interface should be located in the ancestral layer 100
Notice type single double
type double network)
3.01 Chongshan combined
River rush mountain grid
1(1 impact combined estimate
not less than 1 process purpose wind value
strict standard health to cold power zone expansion ring, more potential winter drop zone U time outside large area no measurement effect, air, ditch. Agent from welcome you 240.35
style anti-expansion layer internal resistance no water paint migration
electricity no or go to surface protective agent fall
1 design and the pressure breaking part does not hold in each total boundary o.
The brick surface must be protected from burning under the design intensity level. After the test, the change is less than 1%. Table 4 Interface mortar performance index
When ice melts
The performance of the powder should meet the requirements of the table. Table 5
Two times
Final time
Safety (type)
Air viscosity
Clear water pull strength
Glue powder performance index
JG158—2001
5.4 Aggregate two particles
Case study The performance of the topic particle should meet the requirements of Table 6. Performance index of the topic particle with adenine rate
Reasonable
Sifting residue)
5. 5. The performance of polystyrene granule insulation slurry meets the requirements of the standard. The table shows the performance indicators of polystyrene granule insulation slurry: Function: Comfort: Pressure relief: Dry pressure: Heat resistance: Thermal coefficient: Anti-bacterial strength: Shear adhesion: Linear shrinkage: Softening effect: Flame retardant: 5.6. Requirements for anti-ammonia sand
Anti-crack and anti-slurry performance
Table &, anti-cracking agent and anti-sand performance indicators
Non-volatile matter content
This is in the German standard (±
Release time
Anti-energy sand ticket
Working time
Tensile bonding strength within the working time
Tensile bonding strength
(normally retreat 2B)
Water tension
(full 28 days water 7 mountain
5. 3 --71. 5
183250
Another one + trial yuan agglomeration tax must be calculated, and the extension and expansion of the continuous operation of the high-quality sand case index must come. 7
1 needs to meet G15216
Note: The cement bed adopts a more solid grade 42.5 acid plate, and the GR175 regulations are met. In addition to the floating particles larger than 2.5mm, the impurity content is less than 3%, and the performance of the magnetic mesh
technical network currency meets the requirements of Table 3. .
Two holes Center distance
Unit surface type
Long Kang, wide flow
Breaking strength warp, weft
Sound communication group
Reinforced output
Reinforced type
Left strong front protection vehicle (light school fixed)
Long warp
Tai Tong type
Glass deletion component
5.8 Elastic primer
The performance of competitive bottom should meet the requirements of Table 10, magnetic resistant mesh performance index
N/k nrr
Table 10 Performance index of elastic amine putty
Main condition
Construction pit
Dry nest time
New plastic
Surface integrity rate
Water-resistant acid
Surface drying time
Equidistant drying time
The performance of flexible water-resistant putty shall meet the requirements of Table 11. Table 11
Each state
Constructibility
Dry brushing:
Deep water resistance
Water resistance 6
Adhesion 1
Adhesion
Flexible water-resistant member performance index
Reporting status
Lejiang tax (5 da)
Low storage stability
JG158---204
+3--1,4. 6--..2
Conform to the provisions of JC719: Among them
ZM) 14.5+U, 5, TIO; 6+0. 5
No lumps after collision and mixing, early test and shape change
Good light barrier after deep brushing
No lumps, evenly hooked
Can be beaten by hand
No pregnancy band
Diameter uu invalid
…Cold 1 is not completely oxidized·List of useless classes
JG158—2004
5.19 External wall thermal insulation finishing paint
The external thermal insulation finishing paint must be compatible with the glue powder polymer insulation system. In addition to complying with the national and industry standards, its performance must also meet the performance requirements of Table 1
Table 12 Anti-cracking performance index items of external wall thermal insulation finishing paint
Flat coating materials
Liquid center distance yellowing material
Group type unreasonable yellowing paint
Surface Brick mortar
The surface adhesiveness of the mortar should meet the requirements of Table 13, which refers to the technical properties of the surface adhesive sand. Table 13 Performance indicators of surface adhesive sand: tensile adhesion strength, compression ratio, compression strength, light fastness, water resistance, water resistance, soil resistance, water resistance, etc. The selected type of mortar is 42.5% of the film salt base, and should meet the requirements of (375-199: Sand should meet the requirements of J152-192. The material particle size is 2.5mm and the self-repellent content is less than 2%. The performance of the surface brick hook material should meet the requirements of Table 14. Table 14
1 Performance indicators of brick grout
Control master post joint degree
5.13 Plastic anchor particles
Constant injection rate 14d
Water state 1=d water change 48h.
Permeable sample 21
About the same
With the standard detailed effect
2h small 4
:0, 60
Plastic light consists of two parts: combustible and plastic expansion sleeve with broken disk medicine. The nail skin is made of stainless steel or a full mesh that has been treated to prevent corrosion. The plastic nails and plastic bones with face plates should be made of ethylene or propylene. Recycled materials should not be used as plastic nails and plastic nails. The effective fixing depth of the plastic nail should not be less than 25mm, and the plastic back plate should not be less than 517-1m outside the casing. The tensile bearing capacity standard of a single plastic thread (C cement base) is not less than 5.14 Hot-dip galvanized welded mesh (corner mesh) should comply with (15/H97-1 and meet the requirements of Table 15. Table 15 Performance indicators of hot-dip galvanized welded mesh
Mesh size
Bright spot flow buckle strength
5.15 Finishing resistance
J 158-—2CG4
Thermal control zinc medium quality
o, 9G_>, N
12,7 ×12, 7
The exterior decoration bricks should be made of adhesive with civil description and no stripping agent, and its performance should meet the following current requirements: GB/T 61US:GB/T 4100.1,GB/T 41U0.2.CB/T 4100,3.GB/T 4100, 1:JCT45Y:C5/T 757, and when asked to meet the requirements of the performance indicators in Table 1G Table 16 Screen brick performance indicators
Heart to heart with Rui
6 danger above the end and
Unit area and some
Frost resistance
Clothes surface hand area
Rice surface rent
1,M, 3 relatively hot areas
,, W. Chang area
[,zhou, M hot areas
Tone hot areas
Sichuan, Chang area
Note: The hot areas are implemented according to the 15078-1933 China-Leading Area 1 management area, 5.16
Introduction to the melting promise environment without damage ||tt ||4U Huanma Peng Platinum Ring Element with Damage
Secondly, the induction energy can be extended without damage
Non-rubber resin polyurethane is used in the external insulation system. The accessories, such as the negative beam, case seal, sealing strip, corner protection, and Guanshan strip, shall meet the requirements of the corresponding product standards.
6 Test method
The standard test room environment is air temperature (2312) and relative humidity (50-10)%. When testing in a non-standard test room environment, the temperature and relative humidity should be recorded. This standard test method is used to prepare the mold with oil and micro oil. 1005.6.1 Glue powder is used to prepare the external insulation system
6. 1.1 Resistance to corrosion
According to the provisions of Appendix A.
6.1.2 Water absorption
According to the provisions on the record.
6.1.3 Impact strength
6.1.3.1 Test ladder8 Elastic primer
The performance of competitive primer should meet the requirements of Table 10. Magnetic resistance mesh performance index
N/k nrr
Table 10 Elastic amine removal performance index
Construction stove
Dry nest time
New plastic god
Surface integrity rate
Sensitive water acid resistance
Surface drying time
Equidistant drying time
The performance of flexible water-resistant putty should meet the requirements of Table 11. Table 11
Each state
Constructibility
Dry brushing:
Deep water resistance
Water resistance 6
Adhesion 1
Adhesion
Flexible water-resistant member performance index
Reporting status
Lejiang tax (5 da)
Low storage stability
JG158---204
+3--1,4. 6--..2
Conform to the provisions of JC719: Among them
ZM) 14.5+U, 5, TIO; 6+0. 5
No lumps after collision and mixing, early test and shape change
Good light barrier after deep brushing
No lumps, evenly hooked
Can be beaten by hand
No pregnancy band
Diameter uu invalid
…Cold 1 is not completely oxidized·List of useless classes
JG158—2004
5.19 External wall thermal insulation finishing paint
The external thermal insulation finishing paint must be compatible with the glue powder polymer insulation system. In addition to complying with the national and industry standards, its performance must also meet the performance requirements of Table 1
Table 12 Anti-cracking performance index items of external wall thermal insulation finishing paint
Flat coating materials
Liquid center distance yellowing material
Group type unreasonable yellowing paint
Surface Brick mortar
The surface adhesiveness of the mortar should meet the requirements of Table 13, which refers to the technical properties of the surface adhesive sand. Table 13 Performance indicators of surface adhesive sand: tensile adhesion strength, compression ratio, compression strength, light fastness, water resistance, water resistance, soil resistance, water resistance, etc. The selected type of mortar is 42.5% of the film salt base, and should meet the requirements of (375-199: Sand should meet the requirements of J152-192. The material particle size is 2.5mm and the self-repellent content is less than 2%. The performance of the surface brick hook material should meet the requirements of Table 14. Table 14
1 Performance indicators of brick grout
Control master post joint degree
5.13 Plastic anchor particles
Constant injection rate 14d
Water state 1=d water change 48h.
Permeable sample 21
About the same
With the standard detailed effect
2h small 4
:0, 60
Plastic light consists of two parts: combustible and plastic expansion sleeve with broken disk medicine. The nail skin is made of stainless steel or a full mesh that has been treated to prevent corrosion. The plastic nails and plastic bones with face plates should be made of ethylene or propylene. Recycled materials should not be used as plastic nails and plastic nails. The effective fixing depth of the plastic nail should not be less than 25mm, and the plastic back plate should not be less than 517-1m outside the casing. The tensile bearing capacity standard of a single plastic thread (C cement base) is not less than 5.14 Hot-dip galvanized welded mesh (corner mesh) should comply with (15/H97-1 and meet the requirements of Table 15. Table 15 Performance indicators of hot-dip galvanized welded mesh
Mesh size
Bright spot flow buckle strength
5.15 Finishing resistance
J 158-—2CG4
Thermal control zinc medium quality
o, 9G_>, N
12,7 ×12, 7
The exterior decoration bricks should be made of adhesive with civil description and no stripping agent, and its performance should meet the following current requirements: GB/T 61US:GB/T 4100.1,GB/T 41U0.2.CB/T 4100,3.GB/T 4100, 1:JCT45Y:C5/T 757, and when asked to meet the requirements of the performance indicators in Table 1G Table 16 Screen brick performance indicators
Heart to heart with Rui
6 danger above the end and
Unit area and some
Frost resistance
Clothes surface hand area
Rice surface rent
1,M, 3 relatively hot areas
,, W. Chang area
[,zhou, M hot areas
Tone hot areas
Sichuan, Chang area
Note: The hot areas are implemented according to the 15078-1933 China-Leading Area 1 management area, 5.16
Introduction to the melting promise environment without damage ||tt ||4U Huanma Peng Platinum Ring Element with Damage
Secondly, the induction energy can be extended without damage
Non-rubber resin polyurethane is used in the external insulation system. The accessories, such as the negative beam, case seal, sealing strip, corner protection, and Guanshan strip, shall meet the requirements of the corresponding product standards.
6 Test method
The standard test room environment is air temperature (2312) and relative humidity (50-10)%. When testing in a non-standard test room environment, the temperature and relative humidity should be recorded. This standard test method is used to prepare the mold with oil and micro oil. 1005.6.1 Glue powder is used to prepare the external insulation system
6. 1.1 Resistance to corrosion
According to the provisions of Appendix A.
6.1.2 Water absorption
According to the provisions on the record.
6.1.3 Impact strength
6.1.3.1 Test ladder8 Elastic primer
The performance of competitive primer should meet the requirements of Table 10. Magnetic resistance mesh performance index
N/k nrr
Table 10 Elastic amine removal performance index
Construction stove
Dry nest time
New plastic god
Surface integrity rate
Sensitive water acid resistance
Surface drying time
Equidistant drying time
The performance of flexible water-resistant putty should meet the requirements of Table 11. Table 11
Each state
Constructibility
Dry brushing:
Deep water resistance
Water resistance 6
Adhesion 1
Adhesion
Flexible water-resistant member performance index
Reporting status
Lejiang tax (5 da)
Low storage stability
JG158---204
+3--1,4. 6--..2
Conform to the provisions of JC719: Among them
ZM) 14.5+U, 5, TIO; 6+0. 5
No lumps after collision and mixing, early test and shape change
Good light barrier after deep brushing
No lumps, evenly hooked
Can be beaten by hand
No pregnancy band
Diameter uu invalid
…Cold 1 is not completely oxidized·List of useless classes
JG158—2004
5.19 External wall thermal insulation finishing paint
The external thermal insulation finishing paint must be compatible with the glue powder polymer insulation system. In addition to complying with the national and industry standards, its performance must also meet the performance requirements of Table 1
Table 12 Anti-cracking performance index items of external wall thermal insulation finishing paint
Flat coating materials
Liquid center distance yellowing material
Group type unreasonable yellowing paint
Surface Brick mortar
The surface adhesiveness of the mortar should meet the requirements of Table 13, which refers to the technical properties of the surface adhesive sand. Table 13 Performance indicators of surface adhesive sand: tensile adhesion strength, compression ratio, compression strength, light fastness, water resistance, water resistance, soil resistance, water resistance, etc. The selected type of mortar is 42.5% of the film salt base, and should meet the requirements of (375-199: Sand should meet the requirements of J152-192. The material particle size is 2.5mm and the self-repellent content is less than 2%. The performance of the surface brick hook material should meet the requirements of Table 14. Table 14
1 Performance indicators of brick grout
Control master post joint degree
5.13 Plastic anchor particles
Constant injection rate 14d
Water state 1=d water change 48h.
Permeable sample 21
About the same
With the standard detailed effect
2h small 4
:0, 60
Plastic light consists of two parts: combustible and plastic expansion sleeve with broken disk medicine. The nail skin is made of stainless steel or a full mesh that has been treated to prevent corrosion. The plastic nails and plastic bones with face plates should be made of ethylene or propylene. Recycled materials should not be used as plastic nails and plastic nails. The effective fixing depth of the plastic nail should not be less than 25mm, and the plastic back plate should not be less than 517-1m outside the casing. The tensile bearing capacity standard of a single plastic thread (C cement base) is not less than 5.14 Hot-dip galvanized welded mesh (corner mesh) should comply with (15/H97-1 and meet the requirements of Table 15. Table 15 Performance indicators of hot-dip galvanized welded mesh
Mesh size
Bright spot flow buckle strength
5.15 Finishing resistance
J 158-—2CG4
Thermal control zinc medium quality
o, 9G_>, N
12,7 ×12, 7
The exterior decoration bricks should be made of adhesive with civil description and no stripping agent, and its performance should meet the following current requirements: GB/T 61US:GB/T 4100.1,GB/T 41U0.2.CB/T 4100,3.GB/T 4100, 1:JCT45Y:C5/T 757, and when asked to meet the requirements of the performance indicators in Table 1G Table 16 Screen brick performance indicators
Heart to heart with Rui
6 danger above the end and
Unit area and some
Frost resistance
Clothes surface hand area
Rice surface rent
1,M, 3 relatively hot areas
,, W. Chang area
[,zhou, M hot areas
Tone hot areas
Sichuan, Chang area
Note: The hot areas are implemented according to the 15078-1933 China-Leading Area 1 management area, 5.16
Introduction to the melting promise environment without damage ||tt ||4U Huanma Peng Platinum Ring Element with Damage
Secondly, the induction energy can be extended without damage
Non-rubber resin polyurethane is used in the external insulation system. The accessories, such as the negative beam, case seal, sealing strip, corner protection, and Guanshan strip, shall meet the requirements of the corresponding product standards.
6 Test method
The standard test room environment is air temperature (2312) and relative humidity (50-10)%. When testing in a non-standard test room environment, the temperature and relative humidity should be recorded. This standard test method is used to prepare the mold with oil and micro oil. 1005.6.1 Glue powder is used to prepare the external insulation system
6. 1.1 Resistance to corrosion
According to the provisions of Appendix A.
6.1.2 Water absorption
According to the provisions on the record.
6.1.3 Impact strength
6.1.3.1 Test ladder13 plastic anchor particles
normal injection rate 14d
water state 1=d water change 48h.
permeable sample 21
is approximately consistent
with the standard detailed effect
2h small 4
:0, 60
plastic light consists of two parts: fuel and plastic expansion sleeve with broken disk medicine. The nail skin is made of stainless steel or a full mesh that has been treated to prevent corrosion. The plastic nails and plastic bones with face plates should be made of ethylene or propylene. Recycled materials should not be used as plastic nails and plastic nails. The effective fixing depth of the plastic nail should not be less than 25mm, and the plastic back plate should not be less than 517-1m outside the casing. The tensile bearing capacity standard of a single plastic thread (C cement base) is not less than 5.14 Hot-dip galvanized welded mesh (corner mesh) should comply with (15/H97-1 and meet the requirements of Table 15. Table 15 Performance indicators of hot-dip galvanized welded mesh
Mesh size
Bright spot flow buckle strength
5.15 Finishing resistance
J 158-—2CG4
Thermal control zinc medium quality
o, 9G_>, N
12,7 ×12, 7
The exterior decoration bricks should be made of adhesive with civil description and no stripping agent, and its performance should meet the following current requirements: GB/T 61US:GB/T 4100.1,GB/T 41U0.2.CB/T 4100,3.GB/T 4100, 1:JCT45Y:C5/T 757, and when asked to meet the requirements of the performance indicators in Table 1G Table 16 Screen brick performance indicators
Heart to heart with Rui
6 danger above the end and
Unit area and some
Frost resistance
Clothes surface hand area
Rice surface rent
1,M, 3 relatively hot areas
,, W. Chang area
[,zhou, M hot areas
Tone hot areas
Sichuan, Chang area
Note: The hot areas are implemented according to the 15078-1933 China-Leading Area 1 management area, 5.16
Introduction to the melting promise environment without damage ||tt ||4U Huanma Peng Platinum Ring Element with Damage
Secondly, the induction energy can be extended without damage
Non-rubber resin polyurethane is used in the external insulation system. The accessories, such as the negative beam, case seal, sealing strip, corner protection, and Guanshan strip, shall meet the requirements of the corresponding product standards.
6 Test method
The standard test room environment is air temperature (2312) and relative humidity (50-10)%. When testing in a non-standard test room environment, the temperature and relative humidity should be recorded. This standard test method is used to prepare the mold with oil and micro oil. 1005.6.1 Glue powder is used to prepare the external insulation system
6. 1.1 Resistance to corrosion
According to the provisions of Appendix A.
6.1.2 Water absorption
According to the provisions on the record.
6.1.3 Impact strength
6.1.3.1 Test ladder13 plastic anchor particles
normal injection rate 14d
water state 1=d water change 48h.
permeable sample 21
is approximately consistent
with the standard detailed effect
2h small 4
:0, 60
plastic light consists of two parts: fuel and plastic expansion sleeve with broken disk medicine. The nail skin is made of stainless steel or a full mesh that has been treated to prevent corrosion. The plastic nails and plastic bones with face plates should be made of ethylene or propylene. Recycled materials should not be used as plastic nails and plastic nails. The effective fixing depth of the plastic nail should not be less than 25mm, and the plastic back plate should not be less than 517-1m outside the casing. The tensile bearing capacity standard of a single plastic thread (C cement base) is not less than 5.14 Hot-dip galvanized welded mesh (corner mesh) should comply with (15/H97-1 and meet the requirements of Table 15. Table 15 Performance indicators of hot-dip galvanized welded mesh
Mesh size
Bright spot flow buckle strength
5.15 Finishing resistance
J 158-—2CG4
Thermal control zinc medium quality
o, 9G_>, N
12,7 ×12, 7
The exterior decoration bricks should be made of adhesive with civil description and no stripping agent, and its performance should meet the following current requirements: GB/T 61US:GB/T 4100.1,GB/T 41U0.2.CB/T 4100,3.GB/T 4100, 1:JCT45Y:C5/T 757, and when asked to meet the requirements of the performance indicators in Table 1G Table 16 Screen brick performance indicators
Heart to heart with Rui
6 danger above the end and
Unit area and some
Frost resistance
Clothes surface hand area
Rice surface rent
1,M, 3 relatively hot areas
,, W. Chang area
[,zhou, M hot areas
Tone hot areas
Sichuan, Chang area
Note: The hot areas are implemented according to the 15078-1933 China-Leading Area 1 management area, 5.16
Introduction to the melting promise environment without damage ||tt ||4U Huanma Peng Platinum Ring Element with Damage
Secondly, the induction energy can be extended without damage
Non-rubber resin polyurethane is used in the external insulation system. The accessories, such as the negative beam, case seal, sealing strip, corner protection, and Guanshan strip, shall meet the requirements of the corresponding product standards.
6 Test method
The standard test room environment is air temperature (2312) and relative humidity (50-10)%. When testing in a non-standard test room environment, the temperature and relative humidity should be recorded. This standard test method is used to prepare the mold with oil and micro oil. 1005.6.1 Glue powder is used to prepare the external insulation system
6. 1.1 Resistance to corrosion
According to the provisions of Appendix A.
6.1.2 Water absorption
According to the provisions on the record.
6.1.3 Impact strength
6.1.3.1 Test ladder
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.