title>Micropore anti-counterfeiting marker generated by heavy ion - GB/T 20205-2006 - Chinese standardNet - bzxz.net
Home > GB > Micropore anti-counterfeiting marker generated by heavy ion
Micropore anti-counterfeiting marker generated by heavy ion

Basic Information

Standard ID: GB/T 20205-2006

Standard Name:Micropore anti-counterfeiting marker generated by heavy ion

Chinese Name: 重离子微孔防伪标识

Standard category:National Standard (GB)

state:in force

Date of Release2006-05-01

Date of Implementation:2006-10-01

standard classification number

Standard ICS number:Energy and Heat Transfer Engineering>>Nuclear Energy Engineering>>27.120.99 Other standards related to nuclear energy

Standard Classification Number:Comprehensive>>Social Public Security>>A90 Social Public Security Comprehensive

associated standards

Publication information

publishing house:China Standards Press

Plan number:20020584-T-469

Publication date:2006-10-01

other information

Release date:2006-05-24

Review date:2023-12-28

drafter:Chen Danian, Wang Yulan, Wang Junmin, Zhang Lisheng, Chen Jing, Liu Xuanwei, Lin Jiangheng

Drafting unit:Beijing Tongfang Touchstone New Technology Co., Ltd., Beijing Qingneng Innovation Technology Co., Ltd., Department of Chemistry, Tsinghua University, Institute of Nuclear and New Energy Technology, Tsinghua University, First Research Institute of the

Focal point unit:National Anti-Counterfeiting Standardization Technical Committee

Proposing unit:National Standardization Administration

Publishing department:General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China

competent authority:National Standardization Administration

Introduction to standards:

This standard specifies the terms and definitions, product classification, requirements, test, verification and evaluation methods, acceptance rules, marking, packaging, transportation and storage of heavy ion microporous anti-counterfeiting identification products. This standard applies to anti-counterfeiting identification products based on heavy ion microporous anti-counterfeiting membranes. GB/T 20205-2006 Heavy ion microporous anti-counterfeiting label GB/T20205-2006 standard download decompression password: www.bzxz.net
This standard specifies the terms and definitions, product classification, requirements, test, verification and evaluation methods, acceptance rules, marking, packaging, transportation and storage of heavy ion microporous anti-counterfeiting identification products. This standard applies to anti-counterfeiting identification products based on heavy ion microporous anti-counterfeiting membranes.


Some standard content:

ICS 27. 120.99
National Standard of the People's Republic of China
GB/T20205—2006
Micropore anti-counterfeiting marker generated by heavy ion2006-05-24Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of ChinaStandardization Administration of the People's Republic of China
2006-10-01Implementation
GB/T20205—2006
Normative references
Terms and definitions
Technical safety and confidentiality
Test, verification and assessment methods
Acceptance rules
Marking, packaging, transportation and storage
.....+..
This standard is proposed by the Standardization Administration of the People's Republic of China. Foreword
This standard is under the jurisdiction of the National Anti-Counterfeiting Standardization Technical Committee (SAC/TC218). GB/T20205—2006
The drafting units of this standard are: Beijing Tongfang Touchstone New Technology Co., Ltd., Beijing Qingneng Innovation Technology Co., Ltd., Department of Chemistry of Tsinghua University, Institute of Nuclear and New Energy Technology of Tsinghua University, and First Research Institute of the Ministry of Public Security. Drafters of this standard: Chen Danian, Wang Yulan, Wang Junmin, Zhang Lisheng, Chen Jing, Liu Xuanwei, Lin Jiangheng This standard is published for the first time.
1 Scope
Heavy ion microporous anti-counterfeiting label
GB/T 20205—2006
This standard specifies the terms and definitions, classification, requirements, technical safety and confidentiality, test, verification and evaluation methods, acceptance rules, marking, packaging, transportation and storage of heavy ion microporous anti-counterfeiting label products. This standard applies to anti-counterfeiting label products based on heavy ion microporous anti-counterfeiting film. 2 Normative references
The clauses in the following documents become the clauses of this standard through reference in this standard. For all referenced documents with dates, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties that reach an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For all referenced documents without dates, the latest versions are applicable to this standard. GB/T2792-1998 Test method for 180° peel strength of pressure-sensitive adhesive tape GB/T2828.1 Attribute sampling inspection procedure Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL) (GB/T 2828.1-2003, ISO 2859-1: 1999, IDT) GB/T2829 Attribute sampling procedures and tables for periodic inspection (applicable to inspection of process stability) GB/T17002-1997 Production management specification for anti-counterfeiting printing products GB/T17004-1997 Anti-counterfeiting technical terms
GB/T19425--2003 General technical conditions for anti-counterfeiting technical products 3 Terms and definitions
Heavy ion
Ions heavier than protons are called heavy ions.
Heavy ion microporesmicropore generated by heavy ionnuclear track microporesMicropores formed in insulating materials by irradiating them with heavy ions with a certain amount of energy and after appropriate treatment are called heavy ion micropores, also known as nuclear track micropores.
Heavy ion micropore anti-counterfeiting micropore membrane generated by heavy ionAn insulating material film with anti-counterfeiting information (including patterns) composed of heavy ion micropores. 3.4
Heavy ion micropore anti-counterfeiting markermicropore anti-counterfeiting marker generated by heavy ionAn anti-counterfeiting mark made of heavy ion micropore anti-counterfeiting membrane. 3.5
Explicit patternvisiblepattern
A pattern that is clearly visible to the eye composed of heavy ion micropores. 3.6
Invisible patterninvisiblepattern
A pattern that is invisible to the eye composed of heavy ion micropores and can only be revealed by other means. GB/T 20205—2006
underlay
The substrate bonded to the heavy ion microporous anti-counterfeiting label film, such as paper, aluminized film, laser holographic film or printed plastic film. 3.8
colored
The property that the colored liquid remains in the microporous channels after smearing the heavy ion microporous anti-counterfeiting film with a colored pen and wiping it clean, the pore wall is dyed, and the color is left in the microporous pattern area.
transparent coloring
The property that the colored microporous film is lifted off the surface of the anti-counterfeiting label and the colored liquid is printed on the substrate through the microporous channels. 3.10
transparentwatering
The property that water is dripped on the microporous film and the water fills the micropores, and the entire microporous pattern area becomes transparent, showing the color of the substrate. 4 Classification
4.1 Overt pattern products: Anti-counterfeiting labels made of heavy ion microporous anti-counterfeiting film and paper or plastic backing. The heavy ion microporous anti-counterfeiting film on the label has a clear milky white microporous pattern. 4.2 Hidden pattern products: Anti-counterfeiting labels made of heavy ion microporous anti-counterfeiting film and paper or plastic backing. The microporous pattern cannot be seen on the surface of the label. The microporous pattern can only be revealed by applying color on the heavy ion microporous anti-counterfeiting film. 5 Requirements
5.1 Anti-counterfeiting strength
The anti-counterfeiting strength of heavy ion microporous anti-counterfeiting label products shall comply with the A-level standard specified in GB/T19425-2003. 5.2 Identity uniqueness
The one-time non-transfer rate of heavy ion microporous anti-counterfeiting label products shall not be less than 90%. 5.3 Characteristic requirements
5.3.1 The surface of the label has the property of coloring or disappearing with dripping water. 5.3.2 It should have the function of peeling off the microporous anti-counterfeiting film for coloring, water permeability, print permeability, hole shape, hole diameter, and hole density inspection. 5.3.3 The micropore shape should be cylindrical or conical, with smooth hole walls, micropore density between 2×10*/cm2 and 1×10°/cm2, and hole diameter between 0.5 μm and 10 μm.
5.4 Stability period
The characteristics of heavy ion microporous anti-counterfeiting label products require a stability period of no less than 60 months. 5.5 Identification performance
The identification performance of heavy ion microporous anti-counterfeiting label products is as follows: the pass rate of genuine products is 2 (%), 99≤2≤100; the pass rate of fake products is J (%), J=0.
5.6 Adaptability to use
The adaptability of heavy ion microporous anti-counterfeiting label products should be able to meet the requirements of the subject matter and should comply with the requirements of radioactive health protection. 5.7 Requirements for use environment
The anti-counterfeiting performance of the heavy ion microporous anti-counterfeiting label product should be able to meet the following normal use environment requirements: Ambient temperature: -20℃~50℃;
Ambient humidity: 20%~~85%RH.
5.8 Safety period
The safety period of the heavy ion microporous anti-counterfeiting label product is 36 months. 5.9 Appearance quality
The appearance quality should meet the requirements of Table 1.
Table 1 Appearance
Indicator Name
Image quality
Flatness
Color misalignment
5.10 Relative deviation of die-cutting center
Quality requirements
The pattern area shall not have spots or stains with a diameter greater than 0.5mm. The pattern area shall not have obvious scratches.
The image is clearer
The microporous anti-counterfeiting film and the backing shall be flat and free of warping. The deviation shall not be greater than 0.15mm
GB/T 20205—2006
On the premise of ensuring the integrity of the pattern, the relative deviation of the die-cutting center shall be ≤7%, and the maximum die-cutting center deviation shall be ≤1.5mm. 6 Technical security and confidentiality
Heavy ion microporous anti-counterfeiting label products should have technical security and confidentiality. The specific requirements are as follows: 6.1 Heavy ion microporous anti-counterfeiting label products must be guaranteed by strict security measures. The security measures must be formally documented and must comply with the relevant provisions of GB/T17002-1997.
6.2 Computer graphic files, ink maps, and printing plates used for plate making during the production process should be strictly managed by a dedicated person. 6.3 Trial products and defective products that appear during the production process must be destroyed immediately, with a dedicated person to supervise and keep records of destruction. 6.4 The production environment should meet the requirements of closed management. 6.5 The handover with the user must have necessary procedures. Test, verification and assessment methods
Test environment
Environmental temperature: 23℃±2℃;
Environmental humidity: 50%±5%RH.
7.2 Test method for anti-counterfeiting strengthwww.bzxz.net
The test for anti-counterfeiting strength shall be carried out in accordance with 7.1 of GB/T19425-2003. 7.3 Test method for identity uniqueness
7.3.1 The one-time use non-transfer rate of the anti-counterfeiting mark shall be tested by manual method. 7.3.2 Stick the sample on the target object so that the anti-counterfeiting mark and the test surface are completely bonded. After 24 hours, peel off the sample by hand to observe the degree of damage. If most of the mark is destroyed, it is considered to meet the one-time use non-transfer. 7.4 Measurement of characteristic indicators
7.4.1 Water drop disappearance: Apply water on the mark, the white pattern disappears, and the pattern recovers after the water dries. 7.4.2 Colorability: After smearing the logo with a colored pen and wiping it clean, the pattern area should remain colored. 7.4.3 Coloring water permeability and printability: After smearing the logo with a colored pen and wiping it clean, the pattern area should remain colored. Lift up the upper heavy ion microporous membrane, and the area on the substrate corresponding to the pattern part of the logo membrane should leave a trace of the colored pen. Put the upper heavy ion microporous membrane that has been lifted up on paper, and smear it with a colored pen. The pattern can be printed on the paper. 7.4.4 Hole shape: Observe the pattern area of ​​the logo membrane with an optical microscope measuring device with an accuracy of 1um, and you can see clear cylindrical or conical holes or pits.
7.4.5 Micropore density: Measure the density of micropores (pieces/cm2) under a high-power (40×) microscope. 3
GB/T 20205--2006
7.4.6 Aperture: Measure the diameter of the micropore with an optical microscopic measuring device with an accuracy of 0.5um 7.5 Inspection method for the stable period
Each batch (variety) of products of the enterprise should retain more than 100 pieces for the stable period inspection. During the stable period, 5 labels are sampled every 6 months for the inspection of the characteristic requirements. Those that meet the requirements of 5.3 are qualified. 7.6 Inspection method for identification performance
Use the relevant identification instrument (machine-readable) or manual (non-machine-readable) method to inspect the identification performance of the inspected sample according to the instructions for use to see if it meets the requirements of 5.5.
7.7 Inspection method for use adaptability
Radiation health protection requirements shall be tested by the radiation health protection department in accordance with the relevant regulations and issue a test report. 7.8 Inspection method for use environment requirements
7.8.1 Use temperature range: Paste the label on the target object and place it in a constant temperature box. Observe whether the label is lifted in an environment of 20℃ and 50℃. Take it out after 2 hours and inspect whether the identity uniqueness, characteristic index and recognition performance of the label meet the requirements of 5.2, 5.3 and 5.5.
7.8.2 Humidity: Paste the label on the target object and place it in an environment of 20℃±5℃ and 20% and 85% humidity to observe whether the label is lifted. Take it out after 2 hours and inspect whether the identity uniqueness, characteristic index and recognition performance of the label meet the requirements of 5.2, 5.3 and 5.5.
7.9 Inspection method for safety period
The safety period is inspected by information feedback. If the manufacturer has no user complaints during the safety period, this requirement is qualified. If there are user complaints and they are verified, it is unqualified. 7.10 Appearance inspection
7.10.1 Spots, scratches and flatness: Place the sample flat on a flat glass, set a 20W ordinary light source at a distance of 1m from the sample, and observe the sample at a distance of 0.3m. 7.10.2 Pattern clarity: Place the sample flat on a flat glass, set a 20W ordinary light source at a distance of 1m from the sample, and observe the sample at a distance of 0.3m. All details of the pattern should be clear. 7.10.3 Color misalignment: Use a reading microscope to observe and measure the color misalignment. 7. 11 Measurement of die-cutting center deviation
Put the sample on a flat glass and use a reading microscope to measure with the center of the pattern as the reference. 7.12 Inspection method for technical security and confidentiality Technical security and confidentiality are inspected by verification method. Those who meet all requirements are qualified. 8 Acceptance rules
8.1 Test types
In order to check whether the quality of heavy ion microporous anti-counterfeiting label products meets the requirements of this standard, acceptance tests (factory tests), routine tests and finalization tests (type tests) should be carried out on heavy ion microporous anti-counterfeiting label products. 8.2 Acceptance test
8.2.1 Test objects, sampling locations and methods. The acceptance test of inspection batches is an inspection for the processing defects of products. Each batch of heavy ion microporous anti-counterfeiting label products produced by the manufacturer shall be randomly sampled from the finished product warehouse for inspection according to the requirements of this standard. Products of the same specification submitted for acceptance at the same time are considered as one batch. 8.2.2 Test items
The test items of the acceptance test of heavy ion microporous anti-counterfeiting label products are identity uniqueness, appearance, die-cutting center deviation, and color permeability and permeability inspection.
8.2.3 Sampling plan and qualified judgment
The sampling plan for the acceptance test of heavy ion microporous anti-counterfeiting label products shall adopt GB/T2828.1-General inspection level IⅡ normal inspection 4
times sampling plan
GB/T 20205-2006
The AQL value of the acceptance test items listed in this standard, the sample size of the acceptance test and the qualified judgment number are as follows. The sampling plan for identity uniqueness inspection is shown in Table 2. Table 2 Sampling plan for identity uniqueness inspection
Batch range
35 001~500 000
≥500.001
See Table 3 for the appearance inspection level and sampling plan. Sample
Table 3 Appearance inspection level and sampling plan
Batch range
N35000
35001-150000
150001~500000
≥500001
Number of samples
AQL value
Unit: piece
Unit: piece
Appearance, die cutting center deviation qualified quality level AQL value adoption and defect types are shown in Table 4. The qualified judgment number of the test (pieces) = Ac value × 10.
Table 4 Appearance, die-cutting center deviation detection level Defect category
AQL value
Defect type
Demolding, delamination, misprint, incomplete pattern
Outer dimension out of tolerance, die-cutting center deviation out of tolerance, silicone oil paper damaged 1. The logo film has spots, and the logo is obviously dirty; 2. The logo film or aluminized film is obviously scratched;
3. The printing color is seriously misaligned.
Note 1: Unit products with one or more unqualified products are called unqualified products, and each unit product can only be counted as one unqualified product; Note 2: Unit products with one or more Class A unqualified products, and may also have Class B and (or) Class C unqualified products, are called Class A unqualified products; Note 3: Unit products with one or more Class B unqualified products, and may also have Class C unqualified products but do not include Class A unqualified products, are called Class B unqualified products;
Note 4: Unit products with one or more Class C unqualified products, but do not include Class A or Class B unqualified products, are called Class C unqualified products; Note 5: If there are new defect types, they can be supplemented. See Table 5 for the inspection level and sampling plan of color permeability and permeability. Table 5 Inspection level and sampling plan for color permeability and permeability Batch range
≤500000
≥500001
Routine test
Perform in accordance with 7.3 of GB/T19425--2003. Sample
AQL value 0.65
Unit piece
GB/T20205—2006
8.4 Type test (type test)
Perform in accordance with 7.4 of GB/T19425-2003. 9 Labeling, packaging, transportation and storage
9.1 Product labeling
The following clear and firm labels shall be placed on the heavy ion microporous anti-counterfeiting label products or their inner packaging: a) Product name;
b) Manufacturer's name and address;
Date of production;
d) Safety period.
9.2 Packaging
9.2.1 The inner packaging of the heavy ion microporous anti-counterfeiting label products shall be paper or plastic bags, and the outer packaging shall be corrugated boxes. 9.2.2
Heavy ion microporous anti-counterfeiting label The outer packaging of the product shall have the following clear and firm labels: a)
Product name and model;
Manufacturer name, address and telephone number;
Product quantity;
Product quality standard number;
Net weight and gross weight;
Transportation label;
Outer packaging dimensions.
9.3 Certificate of Conformity
Each package shall be accompanied by a product certificate issued by the quality inspection department of the manufacturer. The following contents shall be indicated on the certificate: a)
Product name and model;
Name and number of the standard that the product quality complies with; date of production;
Inspection date;
Safety period;
Signature of the inspector.
9.4 Transportation
Heavy ion microporous anti-counterfeiting label products shall be able to be transported by normal means of transportation. When transporting products, they shall be protected from sunlight, moisture and rain. 9.5 Storage
Heavy ion microporous anti-counterfeiting label products shall be stored in a ventilated, moisture-proof and fire-proof warehouse. The room temperature and relative humidity in the warehouse shall meet the requirements of the use environment in 5.7.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.