title>Polyurethane foam in- place packaging equipment - BB/T 0056-2010 - Chinese standardNet - bzxz.net
Home > BB > Polyurethane foam in- place packaging equipment
Polyurethane foam in- place packaging equipment

Basic Information

Standard ID: BB/T 0056-2010

Standard Name:Polyurethane foam in- place packaging equipment

Chinese Name: 聚氨酯现场发泡包装设备

Standard category:Packaging Industry Standard (BB)

state:in force

Date of Release2011-01-21

Date of Implementation:2011-04-01

standard classification number

Standard ICS number:Packaging and transportation of goods>>55.200 Packaging machinery

Standard Classification Number:General>>Marking, packaging, transportation, storage>>A84 packaging tools

associated standards

Publication information

publishing house:China Planning Press

Publication date:2011-04-01

other information

Drafting unit:China Packaging Research and Testing Center, Beijing Jinke Polyurethane Technology Co., Ltd.

Focal point unit:National Packaging Standardization Technical Committee

Publishing department:Ministry of Industry and Information Technology

Introduction to standards:

BB/T 0056-2010 Polyurethane foaming-in-place packaging equipment BB/T0056-2010 |tt||Standard compression package decompression password: www.bzxz.net
This standard specifies the terms and definitions, product types and model markings, requirements, test methods, inspection rules and markings, packaging, transportation and storage of polyurethane foaming-in-place packaging equipment. This standard applies to the design, manufacture and inspection of polyurethane foaming-in-place packaging equipment.


Some standard content:

ICS55.200
Packaging Industry Standard of the People's Republic of China
BB/T0056-2010
Polyurethane Foam-in-Place Packaging Equipment
Polyurethane Foamin-Place Packaging Equipment2010-12-29Release
2011-04-01Implementation
Release by the Ministry of Industry and Information Technology of the People's Republic of ChinaAnnouncement of the Ministry of Industry and Information Technology of the People's Republic of China||tt| |Engineering [2010] No. 134
The Ministry of Industry and Information Technology approved 359 industry standards including "Printing Machinery Sharpener" (the standard number, name, main content and implementation date are shown in Appendix 1 and 1 textile industry standard amendment (see Appendix 2), including: 34 mechanical industry standards, 64 light industry standards, 29 textile industry standards, 3 packaging industry standards: 25 electronic industry standards: 200 communication industry standards, and 4 reference technical documents for communication standards. This is now announced. The above mechanical industry standards are published by the Machinery Industry Press, the light industry standards are published by the China Light Industry Press, the textile industry standards are published by the China Standards Press, and the packaging industry standards are published by the China Planning Press: the electronic industry standards are published by the China Electronics Technology Standardization Institute; the communication industry standards are organized and published by the People's Posts and Telecommunications Press, and the reference technical documents for communication standards are issued by the China Communications Standards Association. Attachment: Numbers, names and implementation dates of 3 packaging industry standards Ministry of Industry and Information Technology of the People's Republic of China December 29, 2010
Fii KAoNrKAca
Appendix:
Numbers, names and implementation dates of three packaging industry standards Standard number
BB/T0005—2010
BB/T0056--2010
DB/T0057-—2010
Standard name
Labeling classification and terminology of aerosol products
Polyurethane foam-in-place packaging equipment
Inflatable filling bags for transport
Replaced standard
BB 0005—1995
BB/T0033—2006
Effective date
2011-04-01
2011-04-01
Normative reference documents,
3 Terms and definitions
4 Product type and model marking:
Test method·
Inspection plan·
Marking, Packaging, transportation and storage
FTTKAONTKAca
BB/T0056—2010
BB/T0056--2010
This standard is proposed by China Packaging Federation. Before
This standard is under the jurisdiction of National Packaging Standardization Technical Committee (SAC/TC49). The responsible drafting unit of this standard is China Packaging Research and Testing Center. The participating drafting units of this standard are Shenzhen Meiyingsen Environmental Protection Technology Co., Ltd., Beijing Jinke Polyurethane Technology Co., Ltd., and Saiwen (Tianjin) Industrial Co., Ltd. The main drafters of this standard are Luo Xuan'an, Cai Shaoling, Zhang Zihanwen, Wang Haiyan, and Zhang Yu. I
1 Scope
Polyurethane foaming packaging equipment
BB/T0056-2010
This standard specifies the terms and definitions, product type and model marking, requirements, test methods, inspection rules and marking, packaging, transportation and storage of polyurethane foaming packaging equipment. This standard applies to the design, manufacture and inspection of polyurethane foaming packaging equipment (referred to as foaming machine) in place. 2 Normative references
The clauses in the following documents become the clauses of this standard through reference in this standard. For dated references, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties to an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this standard. GB/T191 Pictorial marking for packaging storage and transportation (IS0780) GB/T5226.1-2002 Mechanical safety Mechanical electrical equipment Part 1: General technical conditions (IEC60204-1) GB/T7311 Classification and model compilation method for packaging machinery GB/T13306 Signage
CB/T15719 Foam-in-place packaging
JB/T7232—1994 Simple method for determination of noise power level of packaging machinery JB7233—-1994
Safety requirements for packaging machinery
3 Terms and definitions
The following terms and definitions apply to this standard. 3.1
Foaming machine polyurethane foam-place packaging equipment can inject a mixture of foaming materials of different components into a mold or between a product and a container to make it foam and solidify. 4 Product type and model marking
4.1 Product type
Product types are divided into: vehicle-mounted, desktop, handheld and foam bag type. 4.2 Model marking
The model of the foaming machine shall be compiled in accordance with the provisions of GB/T7311. FTKAONTKAca
BB/T0056-2010
5 Requirements
5.1 Basic requirements
Derived sequence number: Roman numerals I, Ⅱ, Ⅱ are used to indicate the main parameters: Rated output flow L: (kg/min) Structural type: vehicle-mounted type for \C”, desktop type for \T” Foam bag type \F\ Name code: On-site foaming packaging equipment
5.1.1 The surface coating of the foaming machine equipment should be flat and smooth, with uniform color, without obvious dirt, flow marks, blistering, delamination, rust, scratches, and weld virtual welding.
5.1.2 Each foaming machine shall be equipped with a sign at an obvious location. The sign requirements shall comply with the provisions of GB13306. 5.1.3 The foaming machine shall operate smoothly, and the moving parts shall be sensitive, coordinated and accurate, without jamming and abnormal market response. 5.1.4 The circuit control system of the foaming machine shall be safe and reliable, and the temperature control shall be accurate. 5.1.5 There shall be no leakage of liquid or air at each connection joint. 5.1.6 The mixing head shall be suitable for different mixing ratios of raw materials used for packaging. 5.2 Safety and protection requirementsbzxz.net
5.2.1 The safety and protection requirements of the foaming machine shall comply with the provisions of JB7233-1994. 5.2.2 The foaming machine shall have a reliable grounding device and an obvious grounding mark. 5.2.3 The insulation resistance measured when 500V (dc) is applied between the power circuit conductor and the protective grounding circuit shall be not less than 1MQ5.2.4 All circuit conductors of the equipment and the protective grounding circuit shall be subjected to a withstand voltage test of at least 1s. 5.3 Performance requirements
5.3.1 The noise of the foaming machine should not exceed 75dBA). 5.3.2 The heating temperature control is correct and effective, the adjustment is convenient, the temperature rise is fast, and it can fully meet the process temperature required for foaming. The temperature difference between the set temperature value and the actual temperature value in the working state and the non-working state is ±6℃. 5.3.3 Rated output pressure: 2~4MPa.
5.3.4 Rated output flow: 2~5kg/min. 5.3.5 The material of the material pipe should be heat-resistant, pressure-resistant, and corrosion-resistant, and should not react with chemical raw materials. 5.3.6 The nozzle of the foaming machine should have a self-cleaning cleaning function, and a mechanical cleaning method should be used during packaging. 5.3.7 Foaming packaging products produced from normal raw materials should meet the corresponding requirements of GB/T15719. 6 Test methods
6.1 Basic requirements
According to the provisions of 5.1, observe the operation of the machine by visual inspection and related means, and check the relevant measurement and inspection reports, etc., to verify whether the machine meets the basic requirements.
6.2 Safety and protection test
6.2.1 Check safety and protection, which should comply with the provisions of 5.2.1. 6.2.2 Check the grounding device and measure its grounding resistance according to the provisions of 19.2 of GB/T5226.1-2002. 2
6.2.3 Use an insulation resistance meter to measure its insulation resistance according to the provisions of 19.3 of CB/T5226.1-2002. 6.2.4 Use a withstand voltage tester to perform a withstand voltage test according to the provisions of 19.4 of GB/T5226.1-2002. 6.3 Performance requirements
6.3.1 Noise test.
BB/T 0056-2010
During continuous operation, the noise of the foaming machine shall be measured according to the method specified in JB/T7232-1994, and its noise value shall comply with the provisions of 5.3.1.
6.3.2 Heating temperature deviation detection.
After the foaming machine is running normally and stably, the noise shall be measured with an accuracy of ±1.5℃, 0.2℃ resolution thermometer, measure the temperature once every 0.5min at the outlet, for a total of 3 times. The error between the average value of the 3 measured temperatures and the set heating temperature should comply with the provisions of 5.3.2. 6.3.3 Rated output pressure detection.
Remove any screw plug of the foaming machine, use a two-way joint, one end is connected to the threaded hole of the screw plug, and the other threaded hole is connected to the hydraulic gauge.
Press the trigger grip, the liquid enters the foaming machine, and read the pressure indicated by the hydraulic gauge at the same time. 6.3.4 Rated output flow detection.
While testing the pressure, use a container to hold the liquid ejected for 1min every 5min, and weigh the liquid mass, for a total of 3 weighings, and the maximum value among the 3 weighings is the rated output flow.
6.3.5 Material quality inspection of the material pipe.
First check the material report and quality certificate of the machine parts. When the material cannot be proved, it should be inspected according to the test method of the corresponding material, and an actual compatibility test should be performed. 7 Inspection rules
Inspection is divided into factory inspection and type inspection. 7.1 Factory inspection
7.1.1 Each foaming machine should be inspected by the quality inspection department of the manufacturer according to this standard and can only be shipped with a product certificate. 7.2 Type inspection
7.2.1 Type inspection shall be conducted in any of the following cases: a)
When a new product or an old product is transferred to a factory for trial production and identification; b)
After formal production, if there are significant differences in materials, structure, and process; when the normal production time is one year;
When the product is resumed after a long period of suspension;
When the factory inspection results are significantly different from the last type inspection; f)
When the national quality supervision agency proposes a type inspection requirement. 7.2.2
Type inspection shall include all items in the 5 requirements. Type inspection is qualified if all items of type inspection are qualified. In type inspection, if one of the safety and protection inspections and tests is unqualified, the type inspection is judged to be unqualified. If one of the other items is unqualified, the unqualified item shall be doubled and retested. If it is still unqualified, the product shall be judged to be unqualified in type inspection.
BB/T00562010
8 Marking, packaging, transportation and storage
8.1 Marking
The marking of the packaging box shall comply with the relevant provisions of CB/T191. 8.2
Before packaging the product, the exposed processed surface shall be coated with anti-rust agent. 8.2.1
8.2.2 The product packaging box shall be firm and reliable, and meet the requirements of transportation and loading and unloading. 8.2.3 The packaging box shall have reliable moisture-proof measures. 8.2.4
The special tools and wearing parts of the foaming machine shall be packaged and fixed in the packaging box. The technical documents shall be properly packaged and placed in the packaging box, and shall include the following contents: 8.2.5
Product certificate;
b) Product manual;
c) Packing list.
8.3 Transportation and storage
8.3.1 The foaming machine should be stored in a dry and ventilated place. 8.3.2 The product should be handled with care during transportation. Inversion and collision are not allowed. S/N:15801
158017
Packaging Industry Standard of the People's Republic of China
Polyurethane Foaming Packaging Equipment
BB/T00562010
Published by China Planning Press
(Address: 4th Floor, Building C, Guohong Building, No. 11, Muhuidi Beilijia, Xicheng District, Beijing) (Postal Code: 100038 Tel: 639064336 3906381) Issued by Beijing Xinhuajiedian Publishing House
Printed by Sanhe Fuhua Printing and Packaging Co., Ltd. 880×1230 mm 1/160.5 printing sheet 12,000 words 1st edition in March 2011 1st printing in March 2011 Print run 1-300 copies
Unified book number: 1580177·575
Price: 10.00 yuan
Copyright reserved
Infringements will be investigated
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.