JB/T 6763-1993 YA-W, YA-WF1 series outdoor, outdoor corrosion-resistant and increased safety three-phase asynchronous motors (frame size 80~280)
Some standard content:
Mechanical Industry Standard of the People's Republic of China
YA-W, YA-WF1 series outdoor, outdoor corrosion-resistant and increased safety three-phase asynchronous motors (frame size 80~280) 1 Subject content and scope of application
JB6763--1993
This standard specifies the types, basic parameters and dimensions, technical requirements, test methods, inspection rules and marking and packaging requirements of YA-W, YA-WF1 series outdoor, outdoor corrosion-resistant and increased safety three-phase asynchronous motors. This standard applies to YA-W, YA-WF1 series outdoor, outdoor corrosion-resistant and increased safety three-phase asynchronous motors (frame size 80~280) (hereinafter referred to as motors).
The explosion-proof performance of this series of motors meets the requirements of GB3836.3, and the explosion-proof marks are eIT1, eⅡT2, and eIT3. The protection type complies with the provisions of ZBK04003. The special environment codes are W and WF1. Both are suitable for chemical, petroleum, petrochemical and other industrial environments with explosive mixtures of groups T1 to T3 indoors and outdoors. Type W is suitable for environments with slightly corrosive media. Type WF1 is suitable for environments with medium and lower corrosive media.
2 Reference standards
General requirements for explosion-proof electrical equipment for explosive gas environments GB3836.3 Explosion-proof electrical equipment for explosive gas environments Increased safety electrical equipment "e" GB191
GB1032
GB1993
Packaging, storage and transportation pictorial symbols
Basic technical requirements for rotating electrical machines
Motor structure installation type and code
Three-phase asynchronous motor test method
Motor cooling method
Basic environmental test procedures for electrical and electronic products Test A: Low temperature test method Basic environmental test procedures for electrical and electronic products Test Db: Alternating damp heat test method GB2423.4
GB2900.25 Electrical terminology Motor
GB2900.35 Electrical terminology Explosion-proof electrical equipment for explosive atmospheres GB4772.1
Motor dimensions and tolerances Motors with frame size 36400 flange number FF55~FF1080 or FT55~FT1080 GB4831
Motor product model compilation method
GB4942.1 Motor housing protection classification
GB10068.1 Rotating motor vibration determination method and limit GB10068.2 Rotating motor vibration Vibration measurement method and limit value GB10069.1 Rotating electrical machine noise measurement method and limit value GB12351
JB1045
JB2420
JB4159
JB4375
JB/Z294
Environmental technical requirements for tropical rotating electrical machines
Vibration measurement method
Vibration limit value
Noise engineering measurement method
Chemical gas corrosion test method for electrical products Painting of outdoor and anti-corrosion electrical products
General technical conditions for tropical electrical products
Electrical products for outdoor and indoor use Environmental conditions for use in corrosive places Test method for inter-turn insulation of AC low-voltage motor loose-embedded windings Approved by the Ministry of Machinery Industry on August 21, 1993
Implementation on October 1, 1993
JB/Z340
JB67631993
Test limits for inter-turn insulation of AC low-voltage motor loose-embedded windings ZBK04003 Technical requirements for indoor and outdoor corrosion-proof and explosion-proof asynchronous motors (frame size 45 to 710) Type, basic parameters and dimensions
3.1 The protection level of the motor housing is IP54, and the protection level of the junction box housing is IP55 (see GB4942.1). 3.2 The cooling method of the motor is IC0141 (see GB1993). 3.3 The structure and installation type of the motor are IMB3, IMB5, IMB6, IMB7, IMB8, IMB35, IMV1, IMV3, IMV5, IMV6, IMV15 and IMV36 (see GB997), and it is manufactured according to the provisions of Table 1. Table 1
Frame size
80~160
180~225
250~280
B3, B5, B6, B7, B8, B35, V1, V3, V5, V6, V15, V36B3, B5, B35, V1
B3, B35, V1
3.4 The rating of the motor is a continuous rating based on the continuous working system (S1). 3.5 The rated frequency of the motor is 50Hz, the rated voltage is 380V, the power is 3kW or less, the Y connection is used, and the other powers are △ connection.
3.6 The motor should be manufactured according to the following rated powers: 0.55, 0.75, 1.1, 1.5, 2.2, 3, 4, 5.5, 7.5, 11, 15, 18.5, 22, 30, 37, 45, 55, 75, 90kW3.7
The corresponding relationship between the motor frame number and the speed, power and temperature group should be as specified in Table 2. Table 2
132 ml
T1, T2
T1, T2
T1, T2
T1, T2
160 ml
T1, T2
JB67631993
ContinuedTable 2
T1, T2
T1, T2
Note: The numbers 1 and 2 after S, M and L represent different powers under the same frame number, speed and temperature group. 3.8
Motor dimensions and tolerances
T1, T2
The installation dimensions and tolerances of the motor shall conform to the requirements of Tables 3 to 6, and the overall dimensions shall not be greater than those specified in Tables 3 to 6.
2, 4, 6
2, 4, 6, 8
4, 6, 8
4, 6, 8
4, 6, 8
4, 6, 8wwW.bzxz.Net
YA80YA132
G=D一GE. The limit deviation of GE, frame number 80 is (±0.75
If the position of K hole is qualified, A/2 can be exempted from assessment. Note, 1)
JB6763-1993
YA160～YA280
Table 3 Motor installation with base and no flange on the end cover
, the rest are (
JB6763—1993
YA160～YA280|| tt||Motors with bases and no flanges on end covers and tolerances Positioning tolerance Shape dimensions Note: 1) 2, 4, 6 2, 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 4, 6, 8 If the position of the K hole is qualified, A/2 can be exempted from the assessment. G = D-GE, CE limit deviation Machine seat number 80 (+0.10), c
YA80~YA132
The rest are (
P dimension is the maximum limit value,
R is the distance from the flange mating surface to the shaft shoulder. C
YA160YA280
JB6763-1993
YA80~YA200
Table 4 Motors with base feet and flanges on end covers An
positioning
YA80～YA200
Motors
YA225～YA280
positioning
outer dimensions
2, 4, 6
2, 4, 6, 8
4, 6, 8
YA80YA132
others are (+℃20).
Note: 1) G=D-GE, GE limit deviation, frame size 80 is (+.10), total 0
2) P dimension is the maximum limit value.
3) R is the distance from the flange mating surface to the shaft shoulder T
JB6763-19
YA160~YA225
Motors without base feet and with flanges on the end cover
Position
Outline dimensions
2, 4, 6, 8
4, 6, 8
4, 6, 8
4, 6, 8
4, 6, 8
G=D-GE, the limit deviation of GE is (+0.20) Note: 1)
2) P dimension is the maximum limit value.
3) R is the distance from the flange mating surface to the shaft shoulder. 100
JB67631993
YA180~
Vertical installation, machine base without feet,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.