Some standard content:
Machinery Industry Standard of the People's Republic of China
18/T 8499-96
Electronic Column Ionization Micrometer
1996-11-07 Issued
The Ministry of Machinery Industry of the People's Republic of China Issued and implemented on January 1, 1997
Mechanical Industry Standard of the People's Republic of China
Electronic Column Ionization Micrometer
Subject Content and Scope of Application
JA/T B499—96
This standard specifies the terminology, type, basic parameters, control technology requirements, inspection and adjustment methods, marking and packaging for electronic column ionization micrometers. This standard applies to ordinary electron column ionization micrometers (hereinafter referred to as micrometers). 2 Reference standards
ZBJ42042
IGGCCI
3 Terms
Electronic micro-sensing
General metrological terms and definitions
Electronic products sensing: It is an acoustic inductive sensor that converts the measured inch change into an electrical signal and uses an electronic (light-emitting unit) to display the comparative measurement.
Types and basic parameters
Micro-sensing Only the electric column display and sensor are shown. The type and part names are shown in Figure 1.2 (the type is shown for reference). Market: The scale of the display should be in accordance with the following rules, 0.1.0.2, 0.5, 1.2.5, 10.20. Note that the range is divided by the scale. Philips
Xiyou potentiometer
Ping Electric
Quantity transfer test switch
Electric Duomeng Commercial
Figure 1 Electric-F-column display
Approved by the Ministry of Machinery Industry in 1961
-"Excessive water-increasing ... 8499-96
The surface should not have rust, scratches, coating peeling and other defects: various signs, numbers should be correct and clear: all fixed parts should be reliable, all rotating parts should be flexible, and there should be no jamming and detection. 5.2 Insulation
When the voltage is 5V, the insulation resistance between one wiring of the power supply socket and the electronic display body should be greater than: M. 5.3
When the voltage is ~50 Hz, 1000 Attached, the connection terminal and the electronic display shell are subjected to a withstand voltage test for 1 minute. The display should not have a window cracking phenomenon.
5.4 Display quality
The indication light should be a straight light column, and there should be no distortion. The light should be basically consistent. 5.5 Zero adjustment
The zero range should be within the minimum value range. 5.6 Zero position
The zero position should be within the above range. 5.T Indication variability
The indication variability should not exceed 1 scale value. 5.8 Radial force indication change
The radial force indication should not exceed 1 scale value. 5. Rectification of misinstallation
The error of the process should not exceed 1 scale value.
5. 10 Indication recovery
The indication error within each gear indication range is not reduced by 1 scale value. 5.11 Influence of power supply voltage change on indication When the power supply voltage changes within the new set value within the range of 50H~110H: the indication change caused by it is not longer. 1. In the room,
5.12 Stability change
Under the existing working conditions, the stability of the micrometer indication should not be greater than that specified in Table 1: 1
Scale m
.1. n. 2
5. 13 Measurement force
Set time h
Strengthening expansion
Two allowable intervals
Three allowable intervals
The specified value of the sensor measurement force is.5N, which is allowed to be within the specified range of 50%-120%. 5.14 Materials, Processing and Surface Precision The measuring head shall be made of materials with good electrical resistance. The surface induction of the measuring surface shall not be less than 766HV and the surface roughness shall be Rw.o5ur. 5. 15 Temperature resistance and isothermal properties of the micrometer shall meet the requirements of the test conditions specified in Table 2, and then be placed under high temperature conditions. After three normal inspections, the performance shall be normal. Low temperature resistance and isothermal properties of the micrometer shall meet the requirements of the test conditions specified in Table 2, and then be placed under normal operating conditions. After three normal inspections, the performance shall be normal.
Method and change
Products under the same conditions
Stain resistance test item length (2 items>Test piece, if it is micro-shrinking, it can be normal after inspection, the performance should be normal: 5.18 The original performance
Micrometer combined with two mechanical dynamic platform according to the requirements of Table 4 after the dynamic test, the performance is normal. Wu Si
Protective dynamic request
Female Zong analysis
"Time to reach the dynamic
5.19 Dynamic penetration performance
Big baby Beijing
S, times
c. 1~3. 2 nn
G-- min
For the test instrument packaging, each car is tested, the outer packaging is checked for damage, there is no hidden packaging phenomenon, and the performance should be tested. 6 Test method
6.1 Components
6.1.1 The ambient temperature changes to 30=1℃ and the temperature change is not large. The relative reliability is not large. 70%, 1.2 The input age is small and the dynamic strong magnetic field is 100%, 6.1.3 The micrometer only, the bench needs to be kept isothermal for 12h, the micrometer only should be preheated to 0.5000, and the formal test is carried out after the amplification factor is adjusted.
Power supply.--5c IIz, 220 V
62 input voltage, test method summary test 1 true also table 5 table 5
appearance qualification work
daily test, under the benefit
use insulated electricity virtual add 5V jade, the current battery seat ratio between the line end and the machine without insulated green insect section
daily automatic and wear the general source of the bed
1onoVk certificate 1min
wiring with the machine bright between add·
amine on the ear
insulated type of electricity design
gold display single
stop type
song Shang academic value change north
select immersion
display position course dye
voltage academic dynamic||tt| |京有內期明
智许活
测盘,
耐高诺兰能
JH/T8499—5
续表5
使头低
满量%真整拉示光片,皮托虑一立线,不隔有司空自或象,光冠层产录本,双自然店调下零电气多久得反有有几光单元定天,双娱发和中元应无明品似序列不亲彩请底情况在快分庆助档世,将零调塊器自测又改出問題变战人堂互
在量小分度增风,時精准量分析轻换天案自然次效控制可其会并些量,看亲the value of the car quietly indicated on the learning piece of the exchange process loss under its hundred quantity direction estimation range on the head and the frame two standard ten quantity environment period suitable for the machine to select the factory under the
lift the quantity and sell greater than the total trial acceptance of the file, under the conditions of 1 time, the joint service times indicated the person's position and the recorded small position difference bZxz.net
product points divided the head as
find, make the size value also relatively reliable, use the explosion design head in front of the shop at the same time divided the head with the special product design letter 2, resulting in the display of the large product small flow yo space low
is the minimum point of the SARS wide related back diagnosis, so that the test became a single installation to push the transmission fat naturally run wheel transmission learning device to the specification, heavy display for benevolence, effective trial month is a machine to lift the head lightly, its daily quantity should be six The pressure control of the family piece, then the hand wheel is closed, the mountain is still the way of the beans, the joint piece evenly aligns the piece on the measuring platform, the family demonstration of the four equal parts (or six equal parts) of the network of the group, in turn, the fixed point of the display position, the joint woman position
will lead the switch to the minimum position, note the text and the work of the test bench: quickly adjust the display, the pointer through the ten-step range, from the power supply ~ AnH223V, the switch is switched to the small range when the L, make the probe and the test bench face the technical touch to adjust the display value to make it close to the flow, cut off the blood supply, narrow 2 times, turn on and heat, the heat is 0.5 readings later, in the small shock time, the blue display makes the sensor installed on the piece of measuring head at the maximum self-impact state and then the month to the power treatment method of the head operation method at the same time the head slowly power please pay attention to the electronic display to obtain the display is still in the event of the communication as the actual effect, then win again make the control habit and move, the display value through the standard time can be stored in the meter installed normally send the internal level information to the intelligent production of the sales, so that the speed of zero, the combination of the German laser instrument. 6-24 record 5. [-.13 for the joy of experience || tt| |Put the micrometer in the temperature condition of ten, make sure the meter changes quickly, burn the piece and try it out, 16-241 later, drag 51.13 meter to carry out control test
According to the long-term working month
Good needle structure
Embryant holding·
Pressure sample
Voltmeter
Measurement meter
Quickly go to
Test items
Heat resistance
Xiaohang dynamic parts
Thank fast policy in energy
JB/T 8499-96
Test method
The sugar temperature in the test grid is %~
Forming heat for 0.5h:
b. The temperature should be raised to 95% within 3>5h and maintained at 4cT:±2. Within 15h, the temperature should be reduced to 25C±3 within 16hd.H. Keep the temperature still at % and stop measuring instrument. After stabilizing for 16--243, perform inspection by fast recording method on 5.1--5.14.
Put the packaged products on the table and start the competition according to the regulations. Then! The machine is to be tested according to the 5.1-5.13 clauses. The damaged surface is placed on the 2.5t gauge card, and the vehicle is driven at 40km/h on the 3 sections of 12.5-meter highway at a speed of 300xm. Then the test is carried out according to the 5.1~5.12 clauses. Note: The range of the gauge blocks used for the 17-meter test is as follows. The reading of the gauge block is used as the center for the measurement of the graduation value. 1, 3 gauge blocks are selected: the reading of the graduation value is above, 10, 21μrn is selected, and 5 gauge blocks are selected. Test rules. The micrometer test is divided into two types: "pick-up test" and "type test". 7.1 Factory control inspection
Products can only leave the factory after the factory quality inspection consultation. The inspection items signed by the factory should include the contents of 5.1~5.13. The inspection quantity 7.2 Type inspection
Micrometer type inspection items are 5.1-5.18. Sampling inspection shall be carried out from the products that have passed the factory inspection, and the number of samples shall not be less than 3. Type inspection is carried out when the following conditions exist: During the production trial and adjustment period of the transfer factory, when there are minor changes in the structure, materials and process after formal production, which may affect the product performance; During formal production, at least once every two years: Production interruption "is more than the previous production period, when the national quality supervision department puts forward a request. 3 Determine the standard: All items must be inspected for compliance during the type inspection, and the standard is the core product. If one item is found to be unqualified during the type inspection: Double sampling of detailed products should be conducted in the same batch of test instruments. , conduct inspection on the unqualified products, if there are still unqualified products, the type inspection will not pass. Marking and packaging
Month 1 The label or panel of the display should be marked with: manufacturer name or registered trademark;
Product name and model:
Product serial number:
1. Year and month of manufacture.
8.2 The label should be marked with:
Manufacturer name or registered trademark:
Sensor number:
Product serial number:
Month of manufacture,
JH/T 8499—96
8.3 The packaging of the product should have good rust-proof, moisture-proof and child-proof properties. The outer packaging should have the product name and manufacturer's name, that is, the trademark and "Shanghai", "Anti-overflow", "Anti-\" and other signs. 8.4 The following documents should be attached to the product: a..
Product certificate, which should have the standard code and product serial number card, etc.; instruction manual;
Packing sheet;
8.5 The product should be stored in a warehouse with good air circulation, temperature of 0~40℃ and relative humidity of less than 10.85℃. Micrometer measurement should be avoided during transportation.
Additional instructions:
This standard was proposed by the National Measuring Instrument Standardization Technical Committee. This standard was issued by the Ministry of Industry and Information Technology.
This standard was issued by the Central Plains Animal Exhibition Instrument Research Institute, and the drafters of this standard were Yang Xiujin and Xia Chengzhong. 5
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.