title>JB/T 2001.23-1999 Water system plug (PN=31.5MPa) - JB/T 2001.23-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 2001.23-1999 Water system plug (PN=31.5MPa)
JB/T 2001.23-1999 Water system plug (PN=31.5MPa)

Basic Information

Standard ID: JB/T 2001.23-1999

Standard Name: Water system plug (PN=31.5MPa)

Chinese Name: 水系统 丝堵(PN=31.5MPa)

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-06-28

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:Fluid systems and general parts >> 23.100 Fluid power systems

Standard Classification Number:Machinery>>General Parts>>J20 Hydraulic and Pneumatic Devices

associated standards

alternative situation:JB 2023-1984

Publication information

other information

Focal point unit:Metallurgical Equipment Standardization Technical Committee

Introduction to standards:

JB/T 2001.23-1999 JB/T 2001.23-1999 Water system plug (PN=31.5MPa) JB/T2001.23-1999 Standard download decompression password: www.bzxz.net

Some standard content:

IC.s$ 23.110
Standard of the Machinery Industry of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
Standard of the Machinery Industry of the People's Republic of China
Water system screw plug
Wntersystemr-Serewplug
( PN=31.5 MPa 1
The standard specifies the type, size and technical requirements of the plug. This standard applies to all kinds of channel plugs with a nominal pressure of 31.5MPa. Type 2 or size
2.1 The type shall comply with the provisions of Figure 1.
2.2 The size shall comply with the provisions of Figure 1 and Table 1. Figure
Approved by the State Machinery Industry Bureau on June 28, 1999 46
JR/T 2001.23-1999
Generation B2-84
2000-01-01 Implementation
JBT 2CO1.23.1
FH: 2 23 3
JB/T 200:.23 4
JB:J 200:.23 S
JR-7201.2.3.5
I : 7M1 25
[BT 20C1.23.5
mT 21.23.9
JI 20K1.23.1G
15[M12 6×3
M72 ×4
M9m×4
M心×4
21.HE25151 x
1 Technical requirements for assembly
3. Before welding, the plug must be tightened
1A/T2001.23—1999
32. The two ends of the weld should be welded first, and the isothermal skin should be applied before welding the gaps in the middle. This process should be repeated layer by layer. Except for the first and last layers, the oxide skin should be cleaned as much as possible. When the alloy is fully cooled to the following temperature, use the head to cut gently to make the weld more stable. 3.3. Wear is not allowed There are arc pits: This kind of defect is easy to cause cracks. It is recommended to use T427 or T07 welding rod with a spot diameter of 3 mm. The DC power supply must be reversed, that is, 1 part is the pole, the current is small until the coating turns red,
3.5 When the voltage is low, the electrode head should be 2-3 meters away from the workpiece. 4 Marking to wwW.bzxz.Net
Steel with a nominal diameter of 10mm
DN10JB/T 2001.23.~1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.