title>JB/T 8032.2-1999 Cylindrical feeler gauges for tool setting of machine tool fixture parts and components - JB/T 8032.2-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 8032.2-1999 Cylindrical feeler gauges for tool setting of machine tool fixture parts and components
JB/T 8032.2-1999 Cylindrical feeler gauges for tool setting of machine tool fixture parts and components

Basic Information

Standard ID: JB/T 8032.2-1999

Standard Name: Cylindrical feeler gauges for tool setting of machine tool fixture parts and components

Chinese Name: 机床夹具零件及部件 对刀圆柱塞尺

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-08-06

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)

Standard Classification Number:Machinery>>Process Equipment>>J44 General Fixture

associated standards

alternative situation:JB/T 8032.2-1995 (original standard number GB/T 2245-1991)

Publication information

other information

Focal point unit:Mechanical Science Research Institute

Publishing department:Mechanical Science Research Institute

Introduction to standards:

JB/T 8032.2-1999 This standard is a revision of JB/T 8032.2-95 "Cylindrical feeler gauges for tool setting of machine tool fixture parts and components". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies tool setting cylindrical feeler gauges with specifications of 3~5mm. This standard was first issued in 1981 as GB 2245-80, and was first revised to GB/T 2245-91 on April 30, 1991, and adjusted to JB/T 8032.2-95 in April 1996. JB/T 8032.2-1999 Cylindrical feeler gauges for tool setting of machine tool fixture parts and components JB/T8032.2-1999 Standard download decompression password: www.bzxz.net

Some standard content:

ICS 25. 080. 01
Mechanical Industry Standard of the People's Republic of China
The parts and units of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06Promulgated
State Bureau of Machinery IndustrybZxz.net
Implementation on 2000-01-01
1 Scope
Mechanical Industry Standard of the People's Republic of China
The parts and units of jigs and fixturesCylindrical feeler for tool alignmentThis standard specifies the cylindrical feeler gauge for tool alignment with a specification of 35 mm. 2 Reference standards
JB/T8032.2—1999
Replace JB/T8032.2—1995
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T12981986 Technical conditions for carbon tool steel JB/T8044—1999
3 Dimensions
Technical requirements for machine tool fixture parts and components
The dimensions are shown in the following figure and table.
Reticulation m0.3
Approved by the State Machinery Industry Bureau on 1999-08-06 222
Implemented on 2000-01-01
Basic size
4 Technical conditions
Reporting limit deviation h8
4.1Material: T8 in accordance with GB/T1298. 4.2Heat treatment: 55~60HRC.
JB/T8032.2—1999
(Before knurling)
4.3Other technical conditions in accordance with JB/T8044. 5Marking
5.1Marking example:
D=5mm tool setting cylindrical feeler gauge:
Feeler gauge 5JB/T8032.2—1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.