This standard specifies the definition, product classification, requirements, test methods, inspection rules and marking, packaging, transportation and storage of biaxially oriented polypropylene (BOPP) packaging labels. This standard applies to packaging labels made of biaxially oriented polypropylene (BOPP) film and printed on the surface. QB/T 2666-2004 Biaxially oriented polypropylene packaging labels QB/T2666-2004 Standard download decompression password: www.bzxz.net

1CS 83.080
Classification number: G33
Registration number: 151312005
Light Industry Standard of the People's Republic of China
QB/T2666-2004
Packing label of biaxially ariented polypropylene plain fllm2004-12-14 Issued
National Development and Reform Commission of the People's Republic of China Implemented on 2005-06-01
QE/T2666—2004
Please note that some of the contents of this standard may contain patents. The issuing organization of this standard shall not be responsible for the claim of identifying these patents. This standard is proposed by the National Light Industry Federation:
This standard belongs to the National Technical Committee for Standardization of Frequency Products. This standard is drafted by Zhuhai Zhongding Industrial Co., Ltd. Huang Fu, Huancheng, Huang Langpang, Xu Zheng, Chuan Yiyue, Huang Shaoping, Yu Xiaohui, Dunbing, Shou Dongmei. This standard is published for the first time.
YKANYKea=
1 Scope
Biaxially oriented polypropylene packaging label
OB/T 2666—2004
This standard specifies the definition, product classification, requirements, test methods, inspection rules, marking, packaging, etc. of biaxially oriented polypropylene (BOPP) packaging labels
This standard is applicable to packaging labels made of biaxially oriented polypropylene (BOPP) film and printed on the surface. 2 Normative references
The clauses in the following documents are included in this standard through reference. For any referenced document with an old date, all subsequent amendments (including the contents of the old date) or revisions are not applicable to this standard. However, the parties who have reached an agreement based on this standard may use the latest version of this document. For any document that is not a previous version, its latest version shall not be used for the standard. BB/T2918-1998 Temporary material test bar state adjustment and test standard environment GB/T6672-2001
Plastic film and sheet thickness determination mechanical measurement method GB/T6673-2001 Determination of film length and width of running material GB/I7707-1987
GB 12904-2003
Guide plate drip printing products
Southern product bar code
GB/T13(22-{991
GR/T14258-:2003
3 Definition
Plastic film lamination test method
Information technology recognition and data collection technology bar code symbol system quality inspection The following meanings apply to this standard.
The phenomenon of printing accuracy caused by insufficient slip or other reasons. 3. 2
The phenomenon caused by excessive release agent in the title or improper operation during printing: 3. 3
Main parts
Refers to the part that reflects the theme of the label, such as patterns, text, logos, etc. 3.4
Electric eye
Refers to the photoelectric tracking mark produced by + dynamic labeling: 4 Product classification
According to the purpose, it is divided into roll label and sheet label 5 Requirements
5. 1 Dimension deviation
QH/T26662004
The deviation can meet the requirements of Table 1.
Voucher packaging, etc.
Sheet packaging, etc.
±1,0am
Eastern deviation
Table 1 Dimension deviation
Degree deviation
Electric eye
=l ruri
The following boundary part is reflected by
±1. 0 iara
The following outer dimensions are determined by the customer's choice of the device, etc., without pressure. Note 1, the length, width, and performance of the device can be used to calculate the size of the space: Note: The length of the L limit line is 4mn.
5. 2[1 Deviation
We are not in compliance with the requirements of the current issue.
Table 2 Overprint deviation
Material printing Guohang
Solid printing
Main department proofreading
Common department meeting
5.3 Nickname
Appearance of the trademark
Ning, patternbZxz.net
Material or appearance
Printing defects
Rui surface uniformity
You Jie Ji Xin
5.4 Interface of the package label
3 Appearance requirements||t t||Change the deviation
Can approve the product without explicit record, etc., the sound sample
Clear feeding fill some, 5 with no intention
No Yan load, learning hole, being surplus tile end, Zong Yan Qing Yan degree is the main part of the design of the whole micro production, attention to the fan silk, the amount of each, the system part is allowed to be obviously polluted by the oil fruit fading, so the fruit state
liquid 1m, a diameter
Push the label to allow the label to have a mark, the piece of stains allowed slight mark disease should not have the age of the month set trap
5.4.! The position has been accurately replaced, the glued label becomes a complete label, the door should be in the middle of the unit label, connect! Compensation! 5.4.2 The number of connections per Dunchang shall meet the requirements of Table 3. 5.5 Adhesion performance The number of connections/pieces shall meet the requirements of Table 3. 5.6 If the performance is not solid, the filter shall not fall off. 5.7 Repeatedly press the printed surface with double dry soft for 10 times, and there is no flake falling off. 5.8 Scratch resistance The new printed label shall be scratched with a fingernail for 0 times, and there is no flake falling off. 5.9 Mechanical properties of the label The mechanical properties of the label shall meet the requirements of 5. 5 Physical and mechanical properties
Present this but /MPa
5.10 Low temperature performance
Recognition period of cracking /%
Label When -20℃ low temperature, plastic has no peeling. 5.11 High temperature resistance
When the label is high, the rate of no peeling
5.12 Barcode
5, the total effective, 9 card sense years meet the requirements of BF12904-2003. 6 Test method
6.1 Test state adjustment and test standard dynamic environment QB/T2G66-2004
With temperature /a1
According to GB/2918-19 specified temperature table, it is necessary to edit the hall, usually the pot grass out of the plan: the sample state is adjusted when not less than 1 king. 6.2 Dimensional deviation
6.2.1 Length and width
In accordance with 6B/T6673-20.
6.7.2 Thickness
In accordance with GT/6672-2001. Use a pressure gauge with a precision of 0.01mm to measure. 6.2.3 Width of electric eye
Use a measuring tool with a precision of 0.5mm to measure. 6.2.4 The dimensions of the upper and lower boundary parts
Make sure the margin is not less than 0.5 mm; also measure. 6.3 Printing deviation
F25 parts are replaced by a mirror for inspection.
QB/T2666—2004
8.4 Appearance
Under natural light or fluorescent light without illumination, measure the uniformity of the two samples at 0.3m apart: the uniformity of the end surface shall not be less than 1/2mm.
6.5 Interface
Under direct natural light or fluorescent light, measure the uniformity of the two samples at a distance of 3 mm from the sample. 6.6 Adhesion performance
Use the thumb and index finger to peel off the sample at any part of the sample end. If the double-layer test fence can be separated, it is easy to peel off. Otherwise, it is not easy to peel off.
8.7 Adhesion performance
Consider B/T7707—9R7 as specified in 2.3. 6.8 Durability
After the printing is placed for more than 24 hours, use both hands to press the label facing the printing valve with medium force and reversely for 10 seconds, and observe whether it will fall off:
8. 9 Scratch resistance
After the printing agent is placed for more than 24 hours, put it on a flat surface, and use your fingers to scratch the printed surface of the label for several times with medium force and speed, and observe whether it will fall off.
.10 Determination of tensile strength and elongation at break was carried out from 13022 to 1991. The test column was a strip with a length of 150mm and 25mm. The distance between the ignition tools is 100rmm. The test speed should be (250±25)mm/mim. 6.11 Low temperature resistance
Store the label in an ice box at a temperature of -20℃~-10℃ for 24h. Take it out and place it at room temperature. Test the resistance to corrosion, durability and damage, and the flame retardant performance.12 High temperature resistance
Paste the label on the PET commercial product filled with room temperature water, cover it in a 10°C oven, then take it out and cool it to room temperature, and then test its resistance to heat, flexibility, scratch and marking. 6.13 Barcode
Carry out according to GB/T14253-20U3.
Inspection regulations
7.1 Batch
With the same raw materials and continuously produced within 24 hours under the same working condition, the labels of the product category are considered a batch. .2 Sampling
The sampling quantity of each batch of modular labels is 5 rolls, and the sheets will be continuously drawn from the outside of the whole roll: the number of sheets of packaged labels drawn from each batch is as follows (each bundle of labels is 100 sheets), and 5 sheets are drawn from each bundle
7.3 Inspection classification
7.3.1 Delivery inspection
The inspection items are size deviation, overprint deviation, external double digits, closure deviation, attachment performance, operation resistance, engraving resistance, shape and device interface (the inspection time can be agreed upon by both parties if necessary). 7.3.2. Type inspection
When the following conditions occur, type inspection shall be carried out:
When the material and process have changed significantly, which may affect the product performance or when there are major quality problems
When the new product becomes old product, the production shall be conducted internally for trial production:
When the product has been produced for more than three months, the production shall be conducted at least once a year;
When the national quality supervision organization puts forward the requirement of type inspection. The type inspection items are all items of this standard. .4 Judgment rules
QR/26662004
7.4.1 The first batch of products shall be tested according to the customer's technical indicators required by the product in Section 6. If any of the above technical indicators do not meet the requirements, additional testing shall be carried out. If there are more than one roll (sheet packaged product) or one roll (sheet packaged product) of unqualified products, the batch is deemed unqualified. 7.4.2 Determination of type inspection If the type inspection is qualified, the double sample should be re-tested in the middle of the batch. If all the results are satisfactory, the whole batch is qualified. If none of the items in the spot inspection result is qualified, the batch is deemed qualified. 8 Marking. Packaging, transportation and storage 8.1 Marking 8.1.1 The paper should have a certificate of conformity and a certificate indicating the factory name, product name, specification, quantity, batch number (including production date, shift) and inspection stamp; the label should have a labeling method and interface number. 9.1.2 The packaging box should be made of Taiwan cow products, with the name, standard, standard, and standard code! , Yang Humidity, Heat, Prevent and other labels. 9.2 Packaging
The packaging should ensure that the product will not be damaged during transportation and storage, and will not be contaminated by external factors. 8.3 Be careful during transportation
to prevent mechanical contact, contamination, and rain. 8.4 Storage
The product should be stored in a clean, dry, well-ventilated room. It should be properly stacked. The height should be based on the sample height marked on the package. It should not come into contact with other items with odor or ionization. The shelf life is: 6 months.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.