JB/T 5865-1991 Narrow gauge industrial and mining motor wheel series JB/T5865-1991 standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T 5865-1991
Narrow-gauge industrial and mining electric locomotive wheel set series
Published on October 17, 1991
Implementation of the Ministry of Machinery and Electronics Industry of the People's Republic of China on October 1, 1992
Mechanical Industry Standard of the People's Republic of China
Narrow-gauge industrial and mining electric locomotive wheel set series
1 Subject content and scope of application
JB/T58651991
Replaces JB3269-83
This standard specifies the main dimensions, specifications, technical requirements and inspection rules for the narrow-gauge industrial and mining electric locomotive wheel set series. This standard applies to the mass-produced narrow-gauge industrial and mining electric locomotive wheel set series that meets the provisions of JB/B117 "Industrial and Mining Electric Locomotive Series Model", and can also be used as a reference for products outside the model spectrum. 2
Cited standards
GB5675
GB5676
GB4695
GB2828
GB2829
3Product classification
Guidelines for standardization work Provisions for the compilation of product standards Grey cast iron classification
Cast carbon steel for general engineering
Narrow-gauge rolling stock wheel tread shape and dimensional difference
Dimensions, shapes, weights and allowable deviations of hot-rolled round steel and square steel Batch inspection Count sampling procedures and sampling tables Periodic inspection Count sampling procedures and sampling tables Wheel sets are divided into 6 types according to wheel diameter, and the main dimensions should comply with the requirements of Figure 1 and Table 1. 0
Approved by the Ministry of Machinery and Electronics Industry on October 17, 1991, implemented on October 1, 1992
Wheel type
Integral wheel
Integral wheel
Tire wheel
Tire wheel
Tire wheel
Tire wheel
Technical requirements
Wheel diameter
Parts of the wheelset are not allowed to have cracks.
JB/T5865-1991
Outer diameter of wheel center
The difference in rolling circle diameters of the two wheels of a wheelset shall not exceed 1mm. D
Wheel bright hole diameter
Inner distance of wheelsetbzxZ.net
Inner distance of wheelset shall comply with the provisions of Table 1. The circular runout tolerance of the inner end face of any wheel of the press-fit wheelset at the wheel diameter is: 0.5mm.
4.4 The surface roughness parameter Ra value of the wheel position of the axle is: 1.6μm. 4.5 When the wheel is pressed, within the specified tolerance value, the pressing pressure should meet the specified value of the design. 4.6 The materials of each component of the wheel set should meet the following regulations. 4.6.1 The axle should meet the requirements of GB702 and other structural steels with performance not lower than it. 4.6.2 The integral cast steel wheel should meet the requirements of GB5676. 4.6.3 The wheel center should meet the requirements of GB5676 or GB5675. 4.7 The wheel rim tread shape should meet the requirements of GB4695, and except for the wheel with a wheel diameter of 840mm, which adopts the B-type wheel rim tread shape, other specifications of wheels should adopt the A-type. 4.8 The roughness parameter Ra value of the wheel center hole surface is: 3.2μm. Except for the mating surface and tread, the rest of the wheel set should be painted to prevent rust. 4.9
5 Acceptance rules and inspection methods
5.1 The wheelset shall be inspected and accepted by the inspection department of the production unit. If the user needs to conduct random inspections, it should be specified in the contract. 5.2 The chemical composition and mechanical properties of the materials of each part of the wheelset shall be the responsibility of the quality department of the manufacturer. If the user needs to conduct random inspections, it should be specified in the contract.
5.3 Each wheelset shall be inspected for appearance and surface paint quality. 5.4 The overall dimensions and tread shape of the wheel rim shall be inspected for each wheelset. The tread shape of the wheel rim can be inspected with a standard sample, and the gap between the tread shape and the sample should not be greater than 1mm.
5.5 The roughness of the mating surface of the axle and the wheel center hole shall be checked before press-fitting each wheelset. During press-fitting, the pressure and tolerance values ​​shall be recorded separately according to the factory serial number of the wheelset.
5.6 Each batch of wheels can be shipped only after being inspected and qualified according to the requirements of Table 2. Among them, 4.4 and 4.7 of Item 3 of Table 2 can be sampled and inspected according to the general inspection level II of Table 2 of GB2828 and GB2829. When the batch range is 1 to 15 and the batch range is greater than 15, the normal single sampling plan (AQL=4) and the normal double sampling plan (AQL=4) are adopted respectively. 2
Inspection items
Matching surface roughness
JB/T58651991
Assessment requirements
4.1, 4.9
4.2, 4.3, 4. 4
The following steel stamps should be clearly marked on the outer side of the wheel: a.
Manufacturer code or trademark;
Factory serial number;
Manufacturing date;
Technical inspection seal.
The wheel of the wheel stall is painted with three layers of red paint as shown in Figure 2, as a sign to check the loose displacement of the wheel tyre. 6.2
JB/T5865-1991
Additional remarks:
This standard is proposed and managed by the Xiangtan Traction Electrical Equipment Research Institute of the Ministry of Machinery and Electronics Industry. This standard is drafted by the Xiangtan Traction Electrical Equipment Research Institute of the Ministry of Machinery and Electronics Industry. The main drafters of this standard are Gu Xianbao and Zhu Hanshou. 4
People's Republic of China
Mechanical Industry Standard
Narrow Gauge Industrial and Mining Motor Wheel Series
JB/T 58651991
Published and issued by the China Academy of Mechanical Science
Printed by the China Academy of Mechanical Science
(No. 2 Shouti South Road, Beijing
Postal Code 100044)
Number of words XXX,XXX
Format 880×1230
Sheet X/X
Edition X, XX, 19XX
Printing X, XX, 19XX
Number of prints 1-XXX
Price XXX.XX Yuan
XX-XXX
Mechanical Industry Standard Service Network: http://www.JB.ac.cn1661_s98/f
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.