JB/T 5913-1997 This standard is a revision of JB 5913-91 "Electrostatic Precipitator Cathode Wire". This standard specifies the basic type, technical requirements, test methods, inspection rules, packaging, transportation, storage, etc. of electrostatic precipitator cathode wires. This standard applies to listed burr and non-burr cathode wires with a length not exceeding 16m. Other structural types of cathode wires can also be used as a reference. JB/T 5913-1997 Electrostatic precipitator cathode wire JB/T5913-1997 Standard download and decompression password: www.bzxz.net

J88 | | tt | | JB | ||Cathode wire
Implemented on 1998-01-01
Ministry of Machinery Industry of the People's Republic of China
Released
JB/T5913-1997
Previous|| tt||Words
This standard is a revision of JB5913-91< electrostatic precipitator cathode wire. When this standard was revised, spiral, V, line and V were added. At the same time, the shape tolerance "straightness" specified in the original standard was changed to the shape deviation "curvature" according to the characteristics of easy deformation of flexible profiled parts, making the definition and measurement method of shape deviation more reasonable. practical.
This standard will replace JB5913--91 from the effective date. This standard was proposed and coordinated by the Electrostatic Precipitator Sub-Technical Committee of the Environmental Protection Machinery Standardization Technical Committee of the Ministry of Machinery. This standard was drafted by: Kunshan Chengbei Electric Precipitator Equipment Factory. The main drafters of this standard are: Li Yucheng, Yang Mianshou, Sheng Wanrui, Chen Kangyuan, and Zhu Huafu. Scope
1
Machinery Industry Standard of the People's Republic of China
Electrostatic Precipitator
Cathode Wire
JB/T 59131997
Police Agent JB5913 —91
This standard specifies the basic type, technical requirements, test methods, inspection rules, packaging, transportation, storage, etc. of electrostatic precipitator cathode wires. This standard applies to listed thorns and non-old cathode wires with a length not exceeding 16m. Other structural types of cathode wires can also be used as a reference.
Quoted standards
2
The provisions contained in the following standards constitute provisions of this standard through reference in this standard. The versions indicated are valid at the time of publication of this standard. . All standards are subject to revision. Parties using this standard should explore the possibility of using the latest version of the following standards GB 191-90
GB 4879-85
GB 6388-86
JB590891
3
Basic type
3.1
Packaging, storage and transportation pictorial mark
Rust-proof packaging
Transportation packaging receipt and delivery mark| |tt||Sampling inspection and packaging, transportation and storage specifications for the main parts of electrostatic precipitators. The cathode wire of electrostatic precipitator is mainly divided into two types: burred wire and non-barbed wire. The basic types are shown in Table 1 and Figure 1 to Figure 10 . Table 1
awn
thorn
tubular awn wire (referred to as tube awn wire)
aluminum tooth awn wire (referred to as aluminum tooth wire)
Jiaoguo Mangthorn Opera (referred to as Juekuxian)
Fishbone Needle Thread (still called Fishbone Thread)
Vas Thread
Approved by the Ministry of Machinery Industry on 1997-04-15||tt ||Line
Star line
Mangthorn line
Twist star line (Like twist line)
Graphic line
Luo Nan line| |tt||V. Line
1998-01-01 Implementation
1
JB/T 59131997
(b) type b
Figure 1
Pipe Shaped awning line
Picture 2 Sawtooth awning line
Working state
Working state
JB/T 5913-1997
Picture 3| |tt||Angle steel burr line
Double angle steel burr line section
Figure 4
Figure 5 fish bone needle line
Figure 6 Vu line
3.2 Cathode wires of other structural types are allowed to be used as long as the operating performance is not affected. 3.3 The connection type of both ends of the cathode wire shall be determined by the technical agreement or contract requirements between the supplier and the buyer. 4 Technical requirements
4.1 Materials
JB/T5913-1997
4.1.1 The mechanical properties and chemical composition of cathode wire materials should comply with the grades specified in the technical agreement (or contract) between the supplier and the buyer Requirements, 4.1.2 The surface of the cathode wire shall not have serious corrosion, obvious scratches or other defects that affect the mechanical performance. 4.2 thorn line
4. 2. 1
deviation
category
ruler
deviation
shape
deviation
The size and shape deviation of the barbed wire should comply with the requirements of Figures 1 to 6 and Table 2. Table 2 Size deviation and shape deviation items of awning wire
name
item
name
length L
width B
thorn Tip H/2
(tooth height)
distance between adjacent spines (G)
each tip along the entire length
the line connecting the points is parallel to the Yang|| tt||The curvature of the suction plane
Offset
Code name
Smart-shaped thorn line
Cathode line length
2500||tt| |±2
>2500
±+
±1.5
±0. 5
±!
0.7
1000
0.7L
Tooth line
Depolarization line length
2500www.bzxz.net
±2|| tt||>2500
±+
±0. 5
±1
Angle wire
Cathode wire length
$2500
±2
>2500
±+
± 0. 5
±1. 5
100≤10||tt ||0.7L
and ≤10±2.5
1000-
1000
4.2.2 Each incision of the barbed wire and its assembly should be smooth and without obvious Wool and damaging scratches. 10010
mm
Fishbone needle thread and Vs thread
Cathode wire length
≤2500
±2
>2500||tt ||++
*
Lord!
10010
1000
4.2.3 When the burrs of the tubular burr line and the half-circle pipe are welded separately, the solder joints should not penetrate the pipe wall. The solder joints The shear force should not be less than o.6kN.
4.2.4 The body part of the zigzag wire is not allowed to be spliced. 4.2.5 Cross interrupted fillet welding should be used in the middle of the angle steel barbed wire. The solder joints should have no breakdown. material phenomenon. 4.3 Non-burr wire
4.3.1 The surface of star wire (Figure 7) and twist wire (Figure 8) should be smooth and hairless. There should be no hard bends, cracks, gaps and damaging scratches. The inch deviation should meet the following requirements:
a) The deviation of the length (L) of the star line and the twist line is mainly L/1000; b) The deviation of the width (B) of the star line and the twist line is +0.5mmm| | tt | |JB/T 5913--1997
Figure 8
4.3.2 The inner and outer surfaces of the exhaust wire feel smooth to the touch. There are no burrs or damaging scratches. The size deviation and shape deviation should comply with Figure 9 And the provisions of Table 3,
Ka
Figure 9
Table 3
Deviation type
Dimension error
Shape deviation
Day name
Inner diameter D
Length L
hanging head pair
spiral
center plane
twist
Partial quotient
Deviation code
d
E
4.3.3V. Line size deviation and shape deviation should comply with the provisions of Figure 10 and Table 4 . Figure 10
misaligned value
±1
±1.5
+10*
±3
mn||tt| |Deviation category
Dimensional deviation
Shape deviation
5Test method
5.1 Shear test of burr solder joints
Project name
Length L
Width B
JB/T 5913-1997
Table 4||tt ||Deviation code
Central line curvature
Cathode wire length
≤2500
±2
±1
mm|| tt | | > 2500 | The test time is not less than 3 minutes, 5.2 Curvature Measurement
Fix the cathode wire on the special fixture, use a tension straight line as the measurement reference, and stick it closely to the burr tips at both ends of the cathode wire, and measure Measure the distance between the datum and the tip of any thorn. 6 Inspection Rules
6.1 The shear strength of the welding points of the tubular burr wire and the semi-circular pipe shall be inspected for no less than three pieces per batch (no less than two points for each piece). 6.2 Size deviation and shape deviation of each batch of cathode wires·Carry out random sampling inspection according to the requirements of this standard and the provisions of JB5908, 7 Packaging, transportation and storage
7.1 Packaging
7.1.1 Cathode wires should be sealed Packaging and preventing product deformation. Packaging requirements comply with JB5908. 7.1.2 The literature, labels and patterns outside the packaging box should comply with the provisions of JB6388 attached to GB191. 7.1.3 The rust-proof packaging should comply with the provisions of GB4879. 7.1.4 The manufacturer should send the technical documents to the user (or the installation unit) along with the product. Put it in the box and mark it outside the box: a) Packing list:
b) Product certificate;| | tt | 7.2.2 The packaging boxes of cathode wires are stacked. No more than five boxes are stacked. The packaging boxes are not allowed to deform when stacked. 7.3 Purchase and Storage
7.3.1 After the packaging box of the cathode wire arrives at the site, an appropriate flat indoor site should be selected for storage. When stored in the open air, sunlight and rain should be avoided, and there should be no accumulation of water, immersion, or damage to the cathode. Line deformation phenomenon. 7.3.2 When the cathode wire packaging boxes are busy being stored, they should be placed reasonably. The bottom surface must be flat according to the marked position. No other objects should be stacked on the box, 6
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.