The purpose of this standard is to define a series of procedures for certification bodies (non-governmental) to consider when deciding how to deal with the following problems: a) according to reports that the conformity mark issued by the certification body has been misused; or b) the certified product is subsequently found to be hazardous). This standard is equivalent to ISO Guide 27:1983 "Guide for the implementation of corrective action by certification bodies for the misuse of their conformity marks". GB/T 27027-2008 Guide for the implementation of corrective action by certification bodies for the misuse of their conformity marks GB/T27027-2008 Standard download decompression password: www.bzxz.net
The purpose of this standard is to define a series of procedures for certification bodies (non-governmental) to consider when deciding how to deal with the following problems: a) according to reports that the conformity mark issued by the certification body has been misused; or b) the certified product is subsequently found to be hazardous). This standard is equivalent to ISO Guide 27:1983 "Guide for the implementation of corrective action by certification bodies for the misuse of their conformity marks".
This standard is equivalent to ISO Guide 27:1983 "Guide for the implementation of corrective actions by certification bodies for misuse of their conformity marks". For ease of use, this standard has been edited as follows:
--- This guide is uniformly translated as this standard;
--- According to the context, the article numbers of 1.1.1 to 1.1.5 are removed and changed to ---;
--- Chapter 9 has only 9.1 and no subsequent articles, so the article number of 9.1 is deleted.
This standard is proposed and managed by the National Technical Committee for Certification and Accreditation (SAC/TC261).
Drafting units of this standard: China Electronics Standardization Institute, National Certification and Accreditation Administration, China National Accreditation Service for Conformity Assessment, China Taier Certification Center, China Building Materials Inspection and Certification Center, China Quality Certification Center, China Electromagnetic Compatibility Certification Center, NEC Information Systems (China) Co., Ltd., Dayong Software Co., Ltd., Tongfang Co., Ltd.
The main drafters of this standard.

ICS03.120.20
National Standard of the People's Republic of China
GB/T27027—2008/ISOGuide27:1983 Guidelines for corrective action to be taken by a certification body in the event of misuse of its mark of conformity（ISOGuide27.1983,IDT)
Issued on 2008-05-06
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Administration of Standardization of the People's Republic of China
Digital anti-counterfeiting
Implementation on 2008-10-01
GB/T27027-2008/ISOGuide27:1983 This standard is equivalent to ISO Guide 27:1983 "Guidelines for corrective action to be taken by a certification body in the event of misuse of its mark of conformity". For ease of use, this standard has been edited as follows: - "This guide" is uniformly translated as "this standard", - According to the context, the item numbers of "1.1.1~1.1.5" are removed and replaced with "-"; Chapter 9 has only "9.1" and no subsequent items, so the item number "9.1" is deleted. This standard is proposed and managed by the National Technical Committee for Certification and Accreditation of Standardization (SAC/TC261). The drafting units of this standard are: China Electronics Standardization Institute, National Certification and Accreditation Administration, China National Accreditation Service for Conformity Assessment, Taier Certification Center, China Building Materials Inspection and Certification Center, China Quality Certification Center, China Electromagnetic Compatibility Certification Center, NEC Information Systems (China) Co., Ltd., Dayong Software Co., Ltd., Tongfang Co., Ltd. The main drafters of this standard are: Song Hongru, Song Maoen, Shi Xinyong, Wu Jing, Wang Ling, Zhang Hong, Jia Xiangdao, Li Yafang, Deng Yunfeng, Li Huaning, Wang Xiaodong, Chen Zhigang, Tian Zhongling, Liu Hong, Tong Benmin. I
1 Introduction
GB/T27027-2008/IS0Guide27:1983 Guide for the implementation of corrective action by certification bodies in response to misuse of their mark of conformity
1.1 The purpose of this standard is to define a series of procedures for certification bodies (non-governmental) to consider when deciding how to deal with the following situations: a) reports that a mark of conformity issued by the certification body has been misused\ or b) the certified product is subsequently found to be hazardous2. The action taken by the certification body will depend on the specific circumstances. For example, the relevant legal provisions on misuse of the mark of conformity; the nature of the contract or agreement between the certification body and the organization that misused the mark; the severity of the misuse; whether the misuse was accidental or intentional; whether the product is hazardous. . There are two distinct situations in which a manufacturer or seller of a product may be in a misuse of a mark, namely as a misuser or as a discoverer of a product bearing the mark that is subsequently found to be hazardous.
It is more difficult to foresee all potential forms of misuse or any other forms of use that may cause the product bearing the mark to become hazardous than to prevent obvious and common forms of misuse. The hazards caused by these different situations all require corrective measures, but the assessment of liability in each case requires completely different considerations. When deciding what corrective measures to take, the certification body must consider the issues of mass production and sales of products, protect the credibility of its mark, help people who are misled by the misuse of the mark, and treat competitors using the mark equally. In general, the corrective measures described in this standard require the following prerequisites:
--The certification system includes the use of the conformity mark, which is used on each certified product. A certification body has its own registered conformity mark or at least the use of its mark is protected by the law of the country where the certification body is headquartered. Www.bzxZ.net
--A contract or legally binding agreement on the use or misuse of the conformity mark is signed between the certification body and the party authorized to use the mark.
--The party authorized to use the mark has the ability to exercise continuous control over the certified products to ensure that all terms of the contract or agreement are met. 1.2 Where the mark of conformity is falsified or used without any contract or agreement, the certification body shall normally take strong corrective action. Such action shall be in accordance with the relevant provisions of national law on falsification and misuse of the mark. 2 Terms and definitions
recall recall
The collection of the following from the user, market or distribution point by the misuser, the producer or other party responsible for providing the product for use, who subsequently discovers that the product is hazardous 1) "Misuse" may take many forms, such as: a) misuse of the mark or use of the mark on non-conforming products, which are caused by, for example, breach of contract, inadequate quality control, or incorrect assessment by the certification body or laboratory;
b) unauthorized use of the mark, for example, the mark appears on uncertified products. 2) Causes of products that are subsequently found to be hazardous: a) inappropriate standards;
b) unforeseen end use of the product;
c) manufacturing defects.
3) This standard is limited to corrective measures when using the conformity mark; if necessary, the situation of the certificate of conformity can be considered at a later stage. This standard is mainly aimed at non-governmental certification bodies, but it can also be used by government agencies that implement similar certification systems. 1
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.