This standard specifies the technical requirements and inspection methods for the complete state inspection of the main components of 37mm anti-aircraft guns used for artificial weather modification operations. This standard applies to the technical inspection of the 1965 type double-barreled 37mm anti-aircraft guns used for artificial weather modification operations, and other types of 37mm anti-aircraft guns can be implemented as a reference. QX/T 18-2003 Technical Inspection Specification for 37mm Anti-aircraft Guns Used for Artificial Weather Modification Operations QX/T18-2003 Standard Download Decompression Password: www.bzxz.net

2X/18—2003
In order to implement the general practice of artificial weather modification, strengthen the safety management of artificial weather modification operations, standardize the annual inspection of anti-aircraft equipment used in operations, and provide the necessary technical standards in the inspection work, this standard is shortened according to the current technical regulations issued by the Ordnance Department of the General Logistics Department of the People's Liberation Army in 1991 and the technical requirements for the inspection and optical equipment of the single-shot artillery of the General Logistics Department of the People's Liberation Army in 1991. In combination with the actual situation of the artificial weather modification industry, this standard is shortened to Appendix 4, Appendix 5, Appendix 6, Appendix 7, Appendix 8. This standard is under the jurisdiction of China Meteorological Administration:
This standard is issued by the Science and Technology Development Department of the China Meteorological Administration, and this standard is funded by the 73151 Factory of the People's Liberation Army. The authors of this standard are: Chen Jierun, Shen Huiming, Zhou Yueming, Meng Jia, Chen Zhiyu, and Liu Yongming. This standard is issued for the purpose of this publication. 1 Scope Technical inspection specification for 37mm anti-aircraft guns used in artificial weather modification operations 2X/1'18—2003 This standard specifies the technical requirements and inspection methods for the inspection of the main parts of 37mm anti-aircraft guns used in artificial weather modification operations. This standard specifies the technical inspection of the 15-year type 37mm anti-aircraft guns used in artificial weather modification operations. Other types of 37mm anti-aircraft guns may be used in the same manner. 2 Terms and definitions Smoke body cannon The part that can fire projectiles. -Generally includes body, harrel, horn, and port lifting parts 2.2
Body barrel harrel
The main component of the gun body, a tubular part that senses the speed and direction of the bullet during firing, with powder and guide parts inside, 2.3
Cavity gun htre
The internal space of the tube, including the powder chamber, slope and guide space. 2. 4
charge chamber
space in the gun for the cartridge or charge:
cavity line
the rise and fall of the blasting shape on the inner surface of the barrel at a certain angle to the barrel line: 2.6
rinilands
the division of the inner line of the gun,
rinilands
the division of the inner line of the gun,
rinilands
the division of the inner line of the gun
rear recoil
the indicator of the rear half of the gun.
manual openingbreech
manual opening
opening performed by a person,
manual recoil
QX/T1日—2003
recoil performed by a machine or by manpower.
extracting
the process of extracting the medicine from the medicine cage,
counter recail
the process of pressing the half-seat part to move forward from the store half point, 2. 13
the process of changing the traveling operation to the firing position 2.14
loader
the machine to complete or replace the action.
ramnier
the machine to complete or transfer the action.
reuperator
the device to keep the recoil part in the front position for a half time to cancel the recoil of the storage part, and restore the bed position when the goods are recoiled. 2.17
When the machine encounters a fire, recoil should be limited to the specified amount of recoil. 3 Technical requirements for complete state
3.1 The fire extinguishing process should be fixed: the fire rate should be within the range of 0.10mm~1.m (see Figure 1). Unit is old
Dead fire point
3.2 The head is not allowed to have cracks
(01153
Figure 1 Fire single, the gap between the pad and the barrel
3.3 The outer surface of the barrel is not allowed to exceed the specified depth. 3.4 The barrel is not allowed to bend more than the specified depth. 3.5 The barrel is not allowed to have rust and metal protrusions. It does not affect the correct movement of the single text. The wire is used to pierce the swim, and the degree of the wire is free to calculate the effect of the fat
3.6 The diameter of the Yin line of the running account element is 36.5 can. 3.7 The pipe should be sure to be sure that the body and the parts are connected. 3.8 The gap between the back of the barrel and the mirror surface should not be greater than.25mW (see Figure 2) not more than
(o1 19;
ul-4h)
Investigation
Attachment 1>4
/toeos
Qx/118—203
China welcomes Yimi
Rising category Du expansion (by post)
(01 26)bzxZ.net
The distance between the rear end face of the barrel and the door body surface 3.9 The increase in the chamber should not be too low,
3.10 The closing device spring should not be seen to move. The clearance with the inspection should not be less than (mm, see Figure 3) The unit is required meters
《U112/WA702)
4D112PA()
(ut-14)
(01-15)
The distance between the closing device spring and the needle rod should not be less than 3.6
Figure 3 The distance between the closing device spring and the needle rod Figure 4 The clearance between the body and the needle rod tt||3.11 The sagging amount should not be greater than 1.35mm and the external dimension should not be greater than 5.7mm (see Figure 1). 3.12 When the door is in the moon state, the door can rotate flexibly on the door boots, and the door tube cannot enter the gap. When the door is connected to the drawer, the drawer will feel that the punch is detached and the drawer will move away. When the drawer is under the position, the blade should be able to hook the door body; the drawer tube and the punch should not be less than 4 inches, and the contact area should not be less than 5 inches. The door body should not be higher than the bullet size by 0.3-1mm. 5)
X/T 18—2003
Left and right difference?
(0100)
(ei1n )
cannot be less than 4
left, stone rush mourning
(n1133)
(DL-134)
, in the hot shop
25160)
(i11-39)
because 5 draw simple sub and body inspection
*step senmi
3.13 when the film body output bullet is lower than the ground danger output 8 UL~J(TEL The middle support surface of the tow rail is close to the door body: the gap between the upper part of the rail and the half of the door body should not be less than 0.5mm, and the gap between the lower part of the rail and the gap should be within the range of 0.2mm--3.0mm (see Figure 5).
Single letter light
Left, there is a judgment
(0:-100:
Here is the information
0. 2.s. U
not less than 3,5
1 left, rush
rm-134)
t: ground signal
[01-19:
Figure 6 The time between the front and the door is
3.14 The firing mechanism is activated, and the firing pin should be pulled back when the door is opened: the firing pin should be automatically fired after the body is in place (it should not be driven slowly). If it does not fire, the switch column should be lightly covered by the kidney), and the concave pin should be suddenly fired. In the state of the month, the angle between the lever opening and the locking of the firing pin should be ),1=mm~1.19mm. Door parts
(ai-1g)
Card shaft
(111-24)
0. 15-1. 10
Nuclear dynamic expansion (production period>
Figure 7 The lock between the dynamic lever and the trigger card key
(x/T18—2003
Medium fire beside meter
3.15 Closed state sign: The door reaches the same original space should be 0.C1mm~0.701m The door body moves up and down in the door room and becomes 0.2mm~.1.2mmlSee figure).
The unit is the change
(01-45>
0. 04~-0. 70
Switch buckle support curve paste》
Figure door body and question room between
316 missing fixed in H you technical consideration secret movement,
:C1-50)
2. 44~~. 75
This needle is
(01-29)
Please motor protection
[D'-2F
9 The firing pin is protruding and the inspection
3.17 The firing star is 2.44mm~2.75am see Figure 9? The length of the bullet is 6my+-75mm per year
(0:19)
/ (et-a0)
(0151)
3.1 The disassembly and assembly of the near-flow shaft of the bullet-removing machine should be smooth, and the shaft string momentum should not be greater than 1.m: the surface instantaneous danger between the gun and the end face of the bullet body is between C.15tLT-1.50mm: the bullet-removing machine should be consistent with the gun and the bullet, and the ground delivery potential should not be greater than 1.5mm (see Figure 1e
QXT1B-2003
<6169)
(ut-1)
J.151. 30
of the nature of the center. 6
starting machine reverse support body
(01-Iln)
Figure 10 the distance between the ammunition feeder body and the gun
year position is meters
the original repair
3.19 the distance between the front wall of the ammunition feeder should be 386.5m--338.0mm from the center of the ammunition support shaft 13Vmm to 39.rmt see Figure 11
year position is meters
filling road 393
(14-290)
335.5--3860
11 the distance between the front and rear of the ammunition feeder
3.20 the small tooth is lifted each time and returns to its original position naturally after it is released. 3.21 The movable grid should not move up and down or too much, 1. The tester should move left and right.
n42272
DM-22%:
3.22 The drop of the point-to-point machine can be reported and the machine should be within 54mr551. Domestic Beitu 12) 6
Quick source parts
14-21:)
High machine taste
(09-14 )
When removing the idle bottle
(01-230)
Figure 12 The distance between the front directional plate and the two arc surfaces of the ammunition feeder body QX/T18--2033
The unit is meter
3.23 The towing and directional positioning part of the ammunition feeder is 02mm~811. The combined direction of the sliding adjustment of the machine should be 9.02mm--0.70mm (Figure 13). Single
fine bullet machine
(4-111)
a'--s'0
National 13 bullet feeder body sliding and bullet feeder body directional convex part and Qingmu skateboard net 3.24, single Kai, the card plate working surface is not small bottom person 0.3m: the bullet machine has a card plate protruding high worry cloth 4.53m--e.un standard use (see Figure 14)
single busy for the meaning of meters
positive, heart card version
103 23)
(ul-2)
of writing, body
(63 23)
4 original person +.5
Inspection of the working surface of the left and right cardboard of the feeder QX/T18-2003
3.25 The downward clearance after the light bullet is assembled should be 0.3; the front and rear movement should not be greater than 0.7m. The thickness of the three mouths of the feeder surface should not be less than m. See the figure.
Unit is millimeter
Room, right description
519 143
(39-133
Strict machine parts
（B-1A)
Figure 15 Left and right feed hooks are parallel and checked 3.26 Fill the whole groove; when standing in place, the distance between the two feed hooks should not be less than 663, the distance between the feed hook and the feed hook should not be less than 16
The unit is meter
Emergency and confirmation of the bullet
513-143
:13-15)
Skin parts
(rs-34)
New machine translation
Figure 16 Check the opening amount of the feed hook
3.27 The action of the main and right control bolts should be sure. When the brake is closed, the distance between the upper angle of the brake tumbler and the body is (.1nie~1.5mm, and the difference between the lower angle of the right and left brake tumblers should not exceed u.5mm. The position change should not be more than 12.0. When the brake is effective, the spring can only rotate 30\ (see Figure 17) Brake cutting inspection
(046)
Electric express
(412 0)
In the single pair
(114-47)
+ Chengda ten 0.6
The inspection of the left and right brake tumbler center angles
0X/T18—2003
The single speed is mm
3.28 left, the upper lock certificate is higher than the left. When the name is issued, F lock n, 5mm~n, Rmm, the working surface of the launch card lock record should be 1.s mm~3.1 mn(5Figure 18):
The middle position is meter
B0~g'G
:.9~-.1.1
For, the heart-shaped step card understands
(04-63A203)
045604
Left, there is a middle card field
04-215)
(0482)
Figure 18 Left, the inspection base of the middle card lock soil working surface high shoe rainbow opening
1(0-B1
3.29 Pull the loading handle back to the right position! Change it back, the input device body is stuck on the left and right shooting card locks, and the buckle amount should not be less than 3mm. The upper left and middle of the starting device should be 11m-2. The body of the bullet is in the transmission state. The pressure resistance of the rear wall directional surface and the input F are not less than 119):
Qx/18-2Q03
(-22r)
(03-1)
Pointing and body
(30 1A)
Soft parts
<4954)
Opening amount should not be less than!
Not less than 2
Figure 19 Inspection of new projectile body
The middle position is required
Left, right middle and lower
o 2153
(04-82)
District, Qifa Village, Kazhou
;34R3/W>7021
Il4H.IH/WAEu4)
Feng Xuejiang Rod
3.30 The distance between the protruding part and the end face of the ear shaft of the furnace shall not be less than 15m when stepped on and sucked. The interval between the red rod and the elastic belt shall not be less than .1mm. When the board is lowered to the inspection, the protrusion of the yellow rod to the ground ear extraction surface shall not be less than 3mm. The unit board and the re-launch machine shall be able to recover to their original position effectively! Figure 2C is a meter
not less than 3
cost reduction less than 0.6
(1-)
(cs 71)
(05-S4)
Day 2: The distance of the bullet camp to penetrate the effective ear belt surface is 3.31. The light and light are not allowed to occur within the full range of the shooting; the time angle is 11-~-75 within the range of? mmr!~15mml. In the +5.~-7\ range, the surface cost is mm~20m. See Figure 21! .2.30
(0+42)
0.1~0. 4
(05-33-5)
Its, after the replacement of the case, the amount
(9bo1i)
throughflow
(14-65>
Use 21 to reduce the simple and bright interval
UXT18-2003
Unit is only bright meter
3.32 Self-effect machine linkage inspection requirements, open the gun When the bullet is pressed, the training bullet should be pressed into the input bullet. When firing, the training bullet should be quickly pressed, and the training bullet should be fired. When firing, the training bullet should be opened and the number of training bullets should be displayed. The difference between the distance and the scale should not exceed 2m. When re-pressing, the training bullet should be pressed down and the bullet should be automatically adjusted and fired. The momentum of the actuator should not exceed 1mm. The safety device should be sure to act.
3.3 3. The right product cursor is at 58.3N--147.）(6kgf~.5kgl) and the movement should be stable and lazy under the fixed scale.
3.34 When the artillery is firing, the standard length of the tooth should be 150mrv~t7smm, 3.35 The recoil guard should not have a stable phenomenon: the integral margin of the benefit is 4--8 cuts (Figure 22) The frequency should be opened or the type should be determined: the recoil machine shortage should be about 0.51, the liquid quality should meet the requirements, and the type of recoil (No. 2 and No. 4) cannot be mixed. 3.36 The distance between the engraved line of the active end rod and the end face of the temperature machine should be 2%mm~30mm, and it is allowed to be adjusted to 33mm. See 22. The position is the rate type
(0204)
Word Zhejiang
Figure 22 The distance u of the piston rod after the recoil machine is assembled75am see Figure 9? The length of the bullet is 6my+-75mm per year
(0:19)
/ (et-a0)
(0151)
3.1 The disassembly and assembly of the near-flow shaft of the bullet-removing machine should be smooth, and the shaft string momentum should not be greater than 1.m: the surface instantaneous danger between the gun and the end face of the bullet body is between C.15tLT-1.50mm: the bullet-removing machine should be consistent with the gun and the bullet, and the ground delivery potential should not be greater than 1.5mm (see Figure 1e
QXT1B-2003
<6169)
(ut-1)
J.151. 30
of the nature of the center. 6
starting machine reverse support body
(01-Iln)
Figure 10 the distance between the ammunition feeder body and the gun
year position is meters
the original repair
3.19 the distance between the front wall of the ammunition feeder should be 386.5m--338.0mm from the center of the ammunition support shaft 13Vmm to 39.rmt see Figure 11
year position is meters
filling road 393
(14-290)
335.5--3860
11 the distance between the front and rear of the ammunition feeder
3.20 the small tooth is lifted each time and returns to its original position naturally after it is released. 3.21 The movable grid should not move up and down or too much, 1. The tester should move left and right.
n42272
DM-22%:
3.22 The drop of the point-to-point machine can be reported and the machine should be within 54mr551. Domestic Beitu 12) 6
Quick source parts
14-21:)
High machine taste
(09-14 )
When removing the idle bottle
(01-230)
Figure 12 The distance between the front directional plate and the two arc surfaces of the ammunition feeder body QX/T18--2033
The unit is meter
3.23 The towing and directional positioning part of the ammunition feeder is 02mm~811. The combined direction of the sliding adjustment of the machine should be 9.02mm--0.70mm (Figure 13). Single
fine bullet machine
(4-111)
a'--s'0
National 13 bullet feeder body sliding and bullet feeder body directional convex part and Qingmu skateboard net 3.24, single Kai, the card plate working surface is not small bottom person 0.3m: the bullet machine has a card plate protruding high worry cloth 4.53m--e.un standard use (see Figure 14)
single busy for the meaning of meters
positive, heart card version
103 23)
(ul-2)
of writing, body
(63 23)
4 original person +.5
Inspection of the working surface of the left and right cardboard of the feeder QX/T18-2003
3.25 The downward clearance after the light bullet is assembled should be 0.3; the front and rear movement should not be greater than 0.7m. The thickness of the three mouths of the feeder surface should not be less than m. See the figure.
Unit is millimeter
Room, right description
519 143
(39-133
Strict machine parts
（B-1A)
Figure 15 Left and right feed hooks are parallel and checked 3.26 Fill the whole groove; when standing in place, the distance between the two feed hooks should not be less than 663, the distance between the feed hook and the feed hook should not be less than 16
The unit is meter
Emergency and confirmation of the bullet
513-143
:13-15)
Skin parts
(rs-34)
New machine translation
Figure 16 Check the opening amount of the feed hook
3.27 The action of the main and right control bolts should be sure. When the brake is closed, the distance between the upper angle of the brake tumbler and the body is (.1nie~1.5mm, and the difference between the lower angle of the right and left brake tumblers should not exceed u.5mm. The position change should not be more than 12.0. When the brake is effective, the spring can only rotate 30\ (see Figure 17) Brake cutting inspection
(046)
Electric express
(412 0)
In the single pair
(114-47)
+ Chengda ten 0.6
The inspection of the left and right brake tumbler center angles
0X/T18—2003
The single speed is mm
3.28 left, the upper lock certificate is higher than the left. When the name is issued, F lock n, 5mm~n, Rmm, the working surface of the launch card lock record should be 1.s mm~3.1 mn(5Figure 18):
The middle position is meter
B0~g'G
:.9~-.1.1
For, the heart-shaped step card understands
(04-63A203)
045604
Left, there is a middle card field
04-215)
(0482)
Figure 18 Left, the inspection base of the middle card lock soil working surface high shoe rainbow opening
1(0-B1
3.29 Pull the loading handle back to the right position! Change it back, the input device body is stuck on the left and right shooting card locks, and the buckle amount should not be less than 3mm. The upper left and middle of the starting device should be 11m-2. The body of the bullet is in the transmission state. The pressure resistance of the rear wall directional surface and the input F are not less than 119):
Qx/18-2Q03
(-22r)
(03-1)
Pointing and body
(30 1A)
Soft parts
<4954)
Opening amount should not be less than!
Not less than 2
Figure 19 Inspection of new projectile body
The middle position is required
Left, right middle and lower
o 2153
(04-82)
District, Qifa Village, Kazhou
;34R3/W>7021
Il4H.IH/WAEu4)
Feng Xuejiang Rod
3.30 The distance between the protruding part and the end face of the ear shaft of the furnace shall not be less than 15m when stepped on and sucked. The interval between the red rod and the elastic belt shall not be less than .1mm. When the board is lowered to the inspection, the protrusion of the yellow rod to the ground ear extraction surface shall not be less than 3mm. The unit board and the re-launch machine shall be able to recover to their original position effectively! Figure 2C is a meter
not less than 3
cost reduction less than 0.6
(1-)
(cs 71)
(05-S4)
Day 2: The distance of the bullet camp to penetrate the effective ear belt surface is 3.31. The light and light are not allowed to occur within the full range of the shooting; the time angle is 11-~-75 within the range of? mmr!~15mml. In the +5.~-7\ range, the surface cost is mm~20m. See Figure 21! .2.30
(0+42)
0.1~0. 4
(05-33-5)
Its, after the replacement of the case, the amount
(9bo1i)
throughflow
(14-65>
Use 21 to reduce the simple and bright interval
UXT18-2003
Unit is only bright meter
3.32 Self-effect machine linkage inspection requirements, open the gun When the bullet is pressed, the training bullet should be pressed into the input bullet. When firing, the training bullet should be quickly pressed, and the training bullet should be fired. When firing, the training bullet should be opened and the number of training bullets should be displayed. The difference between the distance and the scale should not exceed 2m. When re-pressing, the training bullet should be pressed down and the bullet should be automatically adjusted and fired. The momentum of the actuator should not exceed 1mm. The safety device should be sure to act.
3.3 3. The right product cursor is at 58.3N--147.）(6kgf~.5kgl) and the movement should be stable and lazy under the fixed scale.
3.34 When the artillery is firing, the standard length of the tooth should be 150mrv~t7smm, 3.35 The recoil guard should not have a stable phenomenon: the integral margin of the benefit is 4--8 cuts (Figure 22) The frequency should be opened or the type should be determined: the recoil machine shortage should be about 0.51, the liquid quality should meet the requirements, and the type of recoil (No. 2 and No. 4) cannot be mixed. 3.36 The distance between the engraved line of the active end rod and the end face of the temperature machine should be 2%mm~30mm, and it is allowed to be adjusted to 33mm. See 22. The position is the rate type
(0204)
Word Zhejiang
Figure 22 The distance u of the piston rod after the recoil machine is assembled75am see Figure 9? The length of the bullet is 6my+-75mm per year
(0:19)
/ (et-a0)
(0151)
3.1 The disassembly and assembly of the near-flow shaft of the bullet-removing machine should be smooth, and the shaft string momentum should not be greater than 1.m: the surface instantaneous danger between the gun and the end face of the bullet body is between C.15tLT-1.50mm: the bullet-removing machine should be consistent with the gun and the bullet, and the ground delivery potential should not be greater than 1.5mm (see Figure 1e
QXT1B-2003
<6169)
(ut-1)
J.151. 30
of the nature of the center. 6
starting machine reverse support body
(01-Iln)
Figure 10 the distance between the ammunition feeder body and the gun
year position is meters
the original repair
3.19 the distance between the front wall of the ammunition feeder should be 386.5m--338.0mm from the center of the ammunition support shaft 13Vmm to 39.rmt see Figure 11
year position is meters
filling road 393
(14-290)
335.5--3860
11 the distance between the front and rear of the ammunition feeder
3.20 the small tooth is lifted each time and returns to its original position naturally after it is released. 3.21 The movable grid should not move up and down or too much, 1. The tester should move left and right.
n42272
DM-22%:
3.22 The drop of the point-to-point machine can be reported and the machine should be within 54mr551. Domestic Beitu 12) 6
Quick source parts
14-21:)
High machine taste
(09-14 )
When removing the idle bottle
(01-230)
Figure 12 The distance between the front directional plate and the two arc surfaces of the ammunition feeder body QX/T18--2033
The unit is meter
3.23 The towing and directional positioning part of the ammunition feeder is 02mm~811. The combined direction of the sliding adjustment of the machine should be 9.02mm--0.70mm (Figure 13). Single
fine bullet machine
(4-111)
a'--s'0
National 13 bullet feeder body sliding and bullet feeder body directional convex part and Qingmu skateboard net 3.24, single Kai, the card plate working surface is not small bottom person 0.3m: the bullet machine has a card plate protruding high worry cloth 4.53m--e.un standard use (see Figure 14)
single busy for the meaning of meters
positive, heart card version
103 23)
(ul-2)
of writing, body
(63 23)
4 original person +.5
Inspection of the working surface of the left and right cardboard of the feeder QX/T18-2003
3.25 The downward clearance after the light bullet is assembled should be 0.3; the front and rear movement should not be greater than 0.7m. The thickness of the three mouths of the feeder surface should not be less than m. See the figure.
Unit is millimeter
Room, right description
519 143
(39-133
Strict machine parts
（B-1A)
Figure 15 Left and right feed hooks are parallel and checked 3.26 Fill the whole groove; when standing in place, the distance between the two feed hooks should not be less than 663, the distance between the feed hook and the feed hook should not be less than 16
The unit is meter
Emergency and confirmation of the bullet
513-143
:13-15)
Skin parts
(rs-34)
New machine translation
Figure 16 Check the opening amount of the feed hook
3.27 The action of the main and right control bolts should be sure. When the brake is closed, the distance between the upper angle of the brake tumbler and the body is (.1nie~1.5mm, and the difference between the lower angle of the right and left brake tumblers should not exceed u.5mm. The position change should not be more than 12.0. When the brake is effective, the spring can only rotate 30\ (see Figure 17) Brake cutting inspection
(046)
Electric express
(412 0)
In the single pair
(114-47)
+ Chengda ten 0.6
The inspection of the left and right brake tumbler center angles
0X/T18—2003
The single speed is mm
3.28 left, the upper lock certificate is higher than the left. When the name is issued, F lock n, 5mm~n, Rmm, the working surface of the launch card lock record should be 1.s mm~3.1 mn(5Figure 18):
The middle position is meter
B0~g'G
:.9~-.1.1
For, the heart-shaped step card understands
(04-63A203)
045604
Left, there is a middle card field
04-215)
(0482)
Figure 18 Left, the inspection base of the middle card lock soil working surface high shoe rainbow opening
1(0-B1
3.29 Pull the loading handle back to the right position! Change it back, the input device body is stuck on the left and right shooting card locks, and the buckle amount should not be less than 3mm. The upper left and middle of the starting device should be 11m-2. The body of the bullet is in the transmission state. The pressure resistance of the rear wall directional surface and the input F are not less than 119):
Qx/18-2Q03
(-22r)
(03-1)
Pointing and body
(30 1A)
Soft parts
<4954)
Opening amount should not be less than!
Not less than 2
Figure 19 Inspection of new projectile body
The middle position is required
Left, right middle and lower
o 2153
(04-82)
District, Qifa Village, Kazhou
;34R3/W>7021
Il4H.IH/WAEu4)
Feng Xuejiang Rod
3.30 The distance between the protruding part and the end face of the ear shaft of the furnace shall not be less than 15m when stepped on and sucked. The interval between the red rod and the elastic belt shall not be less than .1mm. When the board is lowered to the inspection, the protrusion of the yellow rod to the ground ear extraction surface shall not be less than 3mm. The unit board and the re-launch machine shall be able to recover to their original position effectively! Figure 2C is a meter
not less than 3
cost reduction less than 0.6
(1-)
(cs 71)
(05-S4)
Day 2: The distance of the bullet camp to penetrate the effective ear belt surface is 3.31. The light and light are not allowed to occur within the full range of the shooting; the time angle is 11-~-75 within the range of? mmr!~15mml. In the +5.~-7\ range, the surface cost is mm~20m. See Figure 21! .2.30
(0+42)
0. 1~0. 4
(05-33-5)
Its, after the replacement of the case, the amount
(9bo1i)
throughflow
(14-65>
Use 21 to reduce the simple and bright interval
UXT18-2003
Unit is only bright meter
3.32 Self-effect machine linkage inspection requirements, open the gun When the bullet is pressed, the training bullet should be pressed into the input bullet. When firing, the training bullet should be quickly pressed, and the training bullet should be fired quickly. When firing, the training bullet should be opened and the number of training bullets should be displayed. The difference between the distance and the scale should not exceed 2m. When re-pressing, the training bullet should be pressed down and the bullet should be automatically adjusted and fired. The momentum of the actuator should not exceed 1mm. The safety device should be sure to act.
3.3 3. The right product cursor is at 58.3N--147.）(6kgf~.5kgl) and the movement should be stable and lazy under the fixed scale.
3.34 When the artillery is firing, the standard length of the tooth should be 150mrv~t7smm, 3.35 The recoil guard should not have a stable phenomenon: the integral margin of the benefit is 4--8 cuts (Figure 22) The frequency should be opened or the type should be determined: the recoil machine shortage should be about 0.51, the liquid quality should meet the requirements, and the type of recoil (No. 2 and No. 4) cannot be mixed. 3.36 The distance between the engraved line of the active end rod and the end face of the temperature machine should be 2%mm~30mm, and it is allowed to be adjusted to 33mm. See 22. The position is the rate type
(0204)
Word Zhejiang
Figure 22 The distance u of the piston rod after the recoil machine is assembledThe position is the rate type
（0204）
Talk about the Zhejiang hit
Figure 22 The distance u of the piston rod after the parking machine is assembled
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.