This standard specifies the classification, technical requirements, test methods, inspection rules, marking, packaging and storage of CKA, CKB, CKZ and CKF one-way sprag overrunning clutches. JB/T 9130-2002 One-way sprag overrunning clutch JB/T9130-2002 Standard download decompression password: www.bzxz.net

1CS21.120.20
Machinery Industry Standard of the People's Republic of China
JB/T91302002
Price Lane 89130—1999
One-way wedge overrunning clutch
Oneways prag overrunning clutch2002-07-16Promulgated
2002-12-01Implementation
National Economic and Trade Commission of the People's Republic of ChinaBefore issuance,
3.2 Model, production batch number
3.3 Running type, basic parameters and main dimensions
4 Technical requirements
Test methods
Inspection rules.
.1 Factory inspection,
5.2 Type inspection,
? Marking, packaging and this
Record A (informative expansion) Clutch selection instructions Figure 1 CKA. One-way overrunning clutch
Figure 2 CKB - One-way overrunning clutch without inner ring Figure 3 CKz - One-way overrunning clutch with bearing Figure 1 CKF non-contact single-core bearing one-way module overrunning clutch Table 1 Clutch type
Table clutch connection type
3 CKA (some types of single-end clutches that can be installed at the end) The main parameters and main dimensions Table 4 CKB one-way overrunning clutch without inner ring. H removal and main dimensions 5 K7 type one-way overrunning clutch with bearing Basic parameters and main dimensions 6 CKF type non-contact bearing one-way overrunning clutch Basic parameters and main dimensions Complete? Clutch pin Main tasks
Table A.1 End coefficient
JB/T9130—2002
JA/T9130—2002
This standard is a revision of B/T9130)—1999: GB/T1.1—2002 and GB/T1.2—2002 were used in the revision of this standard, and the contents such as gear connection, belt pulley connection, sprocket connection, product code, test method, and clutch selection instructions were added to the standard, and technical requirements, inspection rules and four types of connection such as CKA, CKB, CKZ, and CKF were supplemented, and the CK type was eliminated. At the same time, the series specifications were adjusted
The appendix A of this standard is an informational appendix:
This standard replaces JB/T913—1999.
This standard is proposed by the China Machinery Industry Federation. This standard was issued by the National Machinery Axle and Accessory Standardization Technical Committee. This standard was drafted by: Machinery Science Research Institute, Beijing Xinxing Chaoyue Technology Development Co., Ltd. The main drafters of this standard are Zhou Mingheng, Kong Qingtang, Kong Wei, Zhu Chunmei and Ming Cuixin.
1 Scope
One-way wedge overrunning clutch
JB/T9130-2Q02
This standard specifies the CKA, CKE, CFZ and CKF one-way fast overrunning clutches (hereinafter referred to as cylinder clutches): drawings, technical requirements, test methods, inspection rules, marking, packaging and storage. This standard is applicable to one-way, soft-type, reverse overrunning clutches with a nominal torque of 31.5V, m~·25(00V·m. 2 Normative references
The clauses in the following documents become the clauses of the standard through the introduction of this standard: For all referenced documents of the noted period, all subsequent amendments (excluding the content of the period) are not applicable to this standard, however, Before the consultation, all parties involved in the formulation of this standard shall study whether the latest version of this document is used. For any referenced document without a date, the latest version shall be used for this standard. GB/T191-2 (0 Packaging Storage and Transportation Pictorial Marking eqVISO T80: 1997) B/T4879-1999 Rust-proof Packaging GHT6383-1986 Transport Packaging Receiving and Shipping Marking GBT1431938 Classification of Clutches GB/T13384-1992 General Technical Requirements for Packaging of Electromechanical Products YBT91968 Technical Requirements for Stainless Steel 3.1 Type 3.1.1 Clutch structure type, see Table 1. 3.1.2 Clutch connection type, see Table 2. Table 1 Required Clutches Device structure type
Design
Suitable for the maximum speed of -600rrin~·2500r/mrin, light
! Male: Reverse explosion, suitable for cloth loading machine, brushing machine, food machine, medical machine and various bucket elevators, transport machine, spinning machine mechanical transmission JK/T9130—2002
Rotary type ||tt ||Non-contact belt
Bearing type
Needle termination
Table 1 (continued)
Table 2 Clutch connection type
Applicable range
Speed ​​10mi2000m,
35.5N·m11MNa torque, commonly used in Dinghong assembly machine, making machine, bucket assembly production line, microcomputer, lifting machine, electric micro energy and other machine transmission ( Small backstop, center shaft season
Applicable to 600/mL0~150/m speed limit, [BDN-1M--3000N+r speed joint. Commonly used in power transmission machinery, Yijin induction, industrial fast maintenance, chemical machinery, double profit machine board, cement machinery, power station, etc. Backstop:
Use 400cmin--150Ormin speed limit || tt||400Nm~25000N·rpm, speed reducer
Equipped with lifting and pumping equipment: dismantling machine, metallurgical machinery, mining machinery, cement machinery as torsional anti-digger
Connection type
Coal hydrant connection
Gear building
Pulley connection
Wheel connection
Table 2 (thread)
JB/T 91302002
JB/T9130—2002
3.2 Model and product code
3.2.1 Model representation method According to the provisions of GRT10043, series specification code
Structural type code
Chip code (module type)
Assembly code (overrunning clutch)
Example 1: Basic type. The inner diameter of the cage is 180mm and the model is CKA2. Example z: No inner ring type, public transfer 315N+u, shaft diameter 42ra. Model CKB8 Example 3, with shaft type, public transfer cabinet 2800N·m, inner hole diameter 60rum, model CKZ25. Example 4: Non-pull single solid belt fine bearing, nominal light moment 25IkXN, to the ring milk diameter 1Mmm: Model CKFG9.32.2 Product code representation method:
Joint type code
Inner ring hole diameter, single Width:
Unit: mm
Outer ring diameter:
Specification code
Structural type code
Portable type decoupler
Example 1: (KA17 type, outer diameter 140.55, inner diameter 50, clock connection, product code is (KA17-141XS5-50, Example 2: KH8 type, female diameter 72.2B, shaft diameter 42, chain connection, product code Example 3: CK225, outer diameter 230, width 128, inner diameter 75, bolt connection, product code CKZ35--230X128--75L: Example 4. CKP50, outer diameter 17S, width: 7D, inner diameter 100. Gear connection product code CKF50--275×170--100Z 3.3 Structural type, basic parameters and main dimensions 3.3.1 CKA clutch The structural type, basic parameters and main dimensions of the coupler shall comply with the provisions of Figure 1 and the table. Avoid the middle
JBT9130-2D02
1-outer ring: 2-inner ring, 3-pick block! 4-spring meal, 5 hungry column: 6-wrong cover, 7-block Figure, Figure 1CKA one-way block exchange commercial coupler
C pressure 4 (basic type) one-way block surpassing Yu coupler basic net and safety dimensions public property transfer
CKAI-50 × 24—12
C:KA2—55X7418
CKA3—SUX 3420
CK4465 * 26—24
KA5—$ —25
CK4980×32—30
KA70-1X3435
CKAII-
0× 3438
CKA12—.0GX34 40
CKAI3—:1C×3435
(:kA-4 -110x 344U
CKAi5—J30X38
CA!6130×3850
CKA17—J4X.5—50
CKA1S-.40X55—5S||tt| ... 5360
CKA24!S0X 5565
CKA25200X 55-65
CKAZ67(X)X 5570
Nominal torque
Cap. 3 (continued)||tt| ... Inner ring one-way wedge overrunning clutch basic data and main dimensions nominal torque CKE1—40×2516 47×25-18 52×.25-24 High sleeve capacity High transmission Ein:in Shaft model for the same outer diameter: .82 CKB262N28S0: CK11562X2832 CK1t6 62 ×2835
72×2840
872X2642
CKB9—80×32—45
CKB1080×.32—18
C: KRI1—85×32—50
X:436)
CKH14—110X42-65
CEB16—125x42-80
Male torque
4 (threads)
Outer ring mum
12512×.5.0
3.3.3The structural type, main structure and main dimensions of CK2 clutch shall be in accordance with the provisions of Figures 3 and 5. Internal damage: 3-
Replacement: 4-signature: 5-
End cover:
Figure 3CKZ one-way wedge overrunning clutch with bearingJB/T9130-2002
The same multi-diameter
Bearing model
Shaft hair: 8-
TBT9130-2002
Table 5CKZ type one-way wedge overrunning clutch with bearing basic parameters and main dimensions nominal
China
CK21T5 × 50--
CKZ2—80X68-
CKZ3—90 × 70—
CKZ4—1C0 82
CKZ>—110 × U
CKZ6120 x 92
CKz1124 × y2
CEZ8 - 120 × 92
CKV9 125 × 92
CKZ10--125 ×92
CKV11-:3> X U2
CKZ12—130× 92
CK213136X95
CE/14—136X95
K215 — 150 ×
CX7.1G — 150 ×
102: 50
The limit of inner ring exceeding
when
2501300
315!
Two-tube spiral
14×38
R2 1 3.17
C'Kz30
CRZ17 — 150 02-60
CKZ2U — 16 ×
CKZ21 - 1fa ×
CKZ2 170
112-65
CK23170 ×
128—55
CKZ2s —180 180 X
128—65
CXZ2T 180 ×
128—70
CKZ28 — 190 ×
128-65
CKZ29—190 ×
128-70
CK230200*
128—65
CKZ31 - 20G ×
12R—70
Limit when inner ring over-steps
Table 5 (thread)
Two slides
I count the straightness
Light X step
6 × M10
M/T9130—2002
Inner ring m
1 20×4.9
129 ---The structure type, key numbers and dimensions of 3CK2 clutch shall be in accordance with the provisions of Figures 3 and 5. Internal damage: 3-
Replacement: 4-signature: 5-
End cover:
Figure 3CKZ one-way wedge overrunning clutch with bearingJB/T9130-2002
The same multi-diameter
Bearing model
Shaft hair: 8-
TBT9130-2002
Table 5CKZ type one-way wedge overrunning clutch with bearing basic parameters and main dimensions nominal
China
CK21T5 × 50--
CKZ2—80X68-
CKZ3—90 × 70—
CKZ4—1C0 82
CKZ>—110 × U
CKZ6120 x 92
CKz1124 × y2
CEZ8 - 120 × 92
CKV9 125 × 92
CKZ10--125 ×92
CKV11-:3> X U2
CKZ12—130× 92
CK213136X95
CE/14—136X95
K215 — 150 ×
CX7.1G — 150 ×
102: 50
The limit of inner ring exceeding
when
2501300
315!
Two-tube spiral
14×38
R2 1 3.17
C'Kz30
CRZ17 — 150 02-60
CKZ2U — 16 ×
CKZ21 - 1fa ×
CKZ2 170
112-65
CK23170 ×
128—55
CKZ2s —180 180 X
128—65
CXZ2T 180 ×
128—70
CKZ28 — 190 ×
128-65
CKZ29—190 ×
128-70
CK230200*
128—65
CKZ31 - 20G ×
12R—70
Limit when inner ring over-stepping
Table 5 (thread)
Two slides Yaomin
I count Yizhi
Light X step
6 × M10
M/T9130—2002
Inner ring m
1 20×4.9
129 ---The structure type, number and main dimensions of 3CK2 clutch shall be in accordance with the provisions of Figures 3 and 5. Internal damage: 3-
Replacement: 4-signature: 5-
End cover:
Figure 3CKZ one-way wedge overrunning clutch with bearingJB/T9130-2002
The same multi-diameter
Bearing model
Shaft hair: 8-
TBT9130-2002
Table 5CKZ type one-way wedge overrunning clutch with bearing basic parameters and main dimensions nominal
China
CK21T5 × 50--
CKZ2—80X68-
CKZ3—90 × 70—
CKZ4—1C0 82
CKZ>—110 × U
CKZ6120 x 92
CKz1124 × y2
CEZ8 - 120 × 92
CKV9 125 × 92
CKZ10--125 ×92
CKV11-:3> X U2
CKZ12—130× 92
CK213136X95
CE/14—136X95
K215 — 150 ×
CX7.1G — 150 ×
102: 50
The limit of inner ring exceeding
when
2501300
315!
Two-tube spiral
14×38
R2 1 3.17
C'Kz30
CRZ17 — 150 02-60
CKZ2U — 16 ×
CKZ21 - 1fa ×
CKZ2 170
112-65
CK23170 ×
128—55
CKZ2s —180 180 Xbzxz.net
128—65
CXZ2T 180 ×
128—70
CKZ28 — 190 ×
128-65
CKZ29—190 ×
128-70
CK230200*
128—65
CKZ31 - 20G ×
12R—70
Limit when inner ring over-stepping
Table 5 (thread)
Two slides Yaomin
I count Yizhi
Light X step
6 × M10
M/T9130—2002
Inner ring m
1 20×4.9
129 ---
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.