title>CB/T 3887-1999 Small boat inboard propeller shaft ends and propeller hubs - CB/T 3887-1999 - Chinese standardNet - bzxz.net
Home > CB > CB/T 3887-1999 Small boat inboard propeller shaft ends and propeller hubs
CB/T 3887-1999 Small boat inboard propeller shaft ends and propeller hubs

Basic Information

Standard ID: CB/T 3887-1999

Standard Name: Small boat inboard propeller shaft ends and propeller hubs

Chinese Name: 小艇 舷内机桨轴端和桨毂

Standard category:Ship Industry Standard (CB)

state:in force

Date of Implementation:2003-02-01

standard classification number

Standard Classification Number:Ship>>Ship Equipment>>U37 Small Ship Equipment

associated standards

alternative situation:Original standard number: GB 11699-1989; replaced by GB/T 11699-2003

Procurement status:ISO 4566-85 MOD

Publication information

other information

Introduction to standards:

CB/T 3887-1999 Small boat inboard propeller shaft ends and propeller hubs CB/T3887-1999 Standard download decompression password: www.bzxz.net

Some standard content:

UDC629.125:621.824
National Standard of the People's Republic of China
GB11699—89
Small craft-Inboard engine -propellershaft ends and bosses
Published on October 14, 1989
Implemented on May 1, 1990
Published by the State Bureau of Technical Supervision
National Standard of the People's Republic of China
Smallcraft-Inboardengine-propellershaft ends and bosses
This standard is equivalent to the international standard ISO4566—1985 "Shipbuilding 1 Subject content and scope of application
Small craft-Inboard engine-propellershaft ends and bosses".
This standard specifies the main interchangeability requirements for the conical propeller hub inner hole and propeller shaft end with a shaft diameter ranging from 20 to 160 mm, a taper of 1:10, and the keyway bottom parallel to the straight line of the conical surface. This standard applies to small boats with engines installed inside the boat. 2 Reference standards
GB192—81
GB193—81
GB196—81
GB1095—79
GB1096—79
GB1101-79
GB2515—81
3 Terminology
Ordinary thread
Basic tooth profilebzxZ.net
Ordinary thread||t t||Diameter and pitch series (diameter 1 ~ 600mm) Basic dimensions (diameter 1 ~ 355mm)
Ordinary thread
Cross-section dimensions of key and keyway
Ordinary flat key
Key steel
Type dimensions
Ordinary thread terminology
3.1 Nominal diameter
Refers to the large end diameter of the cone at the propeller shaft end without tolerance, which is equal to the diameter of the cylindrical shaft. 3.2 Cone
Refers to the cone section at the propeller shaft end that can transmit all the torque of the propeller shaft to the propeller and allows disassembly at the same time. 4 Main interchangeability requirements
4.1 The structural dimensions shall be as shown in the drawings and tables. 4.2 The "reference dimensions" listed in the table are all nominal dimensions. The nominal diameter and thread major diameter without brackets shall be used first. 4.3 Structure
a. The structural form shown in the figure is for design reference only; b. The manufacturing methods of keys, keyways (including fillet radius), thread flattening height and thread ends, etc., allow for the selection of specific designs and processing methods to meet specific requirements. However, it should be able to transmit all torques, meet connection requirements and have interchangeability;
The structural types not marked with letters in the figure are all non-interchangeability requirements, which can be determined by the manufacturer. c.
4.4 Tolerances
4.4.1 The tolerances for the small end diameter A of the shaft end cone are listed in the table. 4.4.2 The tolerances for the large end diameter B of the hub cone are listed in the table. 4.5 The cone angle tolerance range is equivalent to the diameter tolerance range specified for diameters A and B in 4.4.1 and 4.4.2 respectively. Approved by the State Bureau of Technical Supervision on October 14, 1989 and implemented on May 1, 1990
GB11699-89
4.6 The tolerance of keys and keyways shall comply with the provisions of GB1095, GB1096 and GB1101 for ordinary flat keys and keyways. The tolerance of hub length L shall be ±0.50mm.
4.8 Thread
The effective length of the shaft end thread G shall be equal to the major diameter T of the thread; b.
The thread engagement length of the propeller nut shall not be less than 80% of the effective length G of the shaft end thread; ordinary fine pitch threads shall be selected in accordance with the provisions of GB192, GB193, GB196 and GB2515. Sharp front end face
Structure of propeller hub and propeller shaft end
1-key; 2-propeller nut; 3-propeller shaft end; 4-propeller hub serial number
(85)
Diameter of large end of tapered hole
GB11699—89
Propeller shaft cone
Diameter of small end
Thread at shaft end
36(30)
36(30)
64 (56)
64 (56)
72 (64)
80 (72)
90 (80)
100(90)
100(90)
110(100)
120(110)
Note: The major diameter of the shaft end thread T=14, T=120 is the second series of the nominal diameter of the ordinary thread. 125
Ordinary flat key
Reference size
GB11699—89
The shaft end and the inner hole of the hub designed and manufactured according to the requirements of this standard are marked as follows: Example:
For the shaft end with nominal diameter: D=Φ80mm, it is: Shaft end 80GB11699—89 For the hub with nominal diameter: D=Φ80mm, it is: Hub 80GB11699—89 Additional remarks:
This standard is proposed by China State Shipbuilding Corporation. This standard is under the jurisdiction of the 708th Institute of the 7th Institute of China State Shipbuilding Corporation. This standard was drafted by the 708th Institute of the 7th Institute of China State Shipbuilding Corporation. The main drafter of this standard is Zhang Songhe.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.