title>Graphical symbols for use on equipment-Common symbols for electric welding equipment - GB/T 16273.3-1999 - Chinese standardNet - bzxz.net
Home > GB > Graphical symbols for use on equipment-Common symbols for electric welding equipment
Graphical symbols for use on equipment-Common symbols for electric welding equipment

Basic Information

Standard ID: GB/T 16273.3-1999

Standard Name:Graphical symbols for use on equipment-Common symbols for electric welding equipment

Chinese Name: 设备用图形符号 电焊设备通用符号

Standard category:National Standard (GB)

state:in force

Date of Release1999-03-08

Date of Implementation:1999-09-01

standard classification number

Standard ICS number:General, Terminology, Standardization, Documentation>>Graphic Symbols>>01.080.20 Graphic Symbols for Special Equipment

Standard Classification Number:General>>Basic Standards>>A22 Terms and Symbols

associated standards

Procurement status:ISO 7000-89

Publication information

publishing house:China Standards Press

Publication date:1999-09-01

other information

Release date:1999-05-08

Review date:2004-10-14

drafter:Chen Yuanqiao, Bai Dianyi, Zhang Liang, Hu Hua, Yang Dongbai

Drafting unit:China Institute of Standardization and Information Classification and Coding

Focal point unit:National Technical Committee for Standardization of Graphic Symbols

Proposing unit:China Standards Research Center

Publishing department:State Administration of Quality and Technical Supervision

competent authority:National Standardization Administration

Introduction to standards:

This standard specifies the general graphic symbols for representing the characteristics, operating indicators and functional conditions of various welding equipment. This standard applies to the operating controllers, indicators, connection sockets and nameplates of welding equipment. GB/T 16273.3-1999 Graphic symbols for equipment General symbols for welding equipment GB/T16273.3-1999 Standard download decompression password: www.bzxz.net
This standard specifies the general graphic symbols for representing the characteristics, operating indicators and functional conditions of various welding equipment. This standard applies to the operating controllers, indicators, connection sockets and nameplates of welding equipment.


Some standard content:

GB/T 16273.3--1999
This standard specifies 70 general graphic symbols for welding equipment. These symbols are identical to the relevant symbols in the I507000:1989 New Graphic Special Numbers and List, and are used to indicate the characteristics, operating instructions, functional status, etc. of welding equipment. This standard is one of the series of standards for mushroom-shaped symbols for equipment. The series of standards currently has the following three standards: GB/T16273.1-1996 General symbols for graphic symbols for equipment 5 General symbols for graphic symbols for equipment Machine tools
GB/T 16273.2-1996
9 General symbols for graphic symbols for equipment General symbols for welding equipment GR/T 16273.3-1999
This standard shall be implemented from September 1, 1999. This standard is proposed by the China Institute of Standardization and Information Classification and Coding. This standard is under the jurisdiction of the National Technical Committee for Graphic Symbol Standardization. The drafting units of this standard are: China Institute of Standardization and Information Classification and Coding, Beijing Electric Welding Machine Factory. The main drafters of this standard are: Zhang Liang, Bai Dian-, Chen Yuanqiao, Cui Baokun: 1 Scope
National Standard of the People's Republic of China
Graphical symbols for use on equipment
Common symbols for electric welding equipment
Graphical syabols for use on equpment-Common symbols for electric welding equipment GB/T 16273.3—1999
This standard specifies the common graphic symbols for representing the characteristics, operating instructions and functional status of various electric welding equipment. This standard applies to the operating controllers, indicators, connection sockets and nameplates of electric welding equipment. 2 References
The provisions contained in the following standards become the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and the parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T2900.22-1985 Electrician Terminology Electric Welding Machine GB/T3375-1994 Welding Terminology GB/T5465.2-1996 Graphical Symbols for Electrical Equipment (idtIEC417:1994) GB/T15565-1995 Graphical Symbol Terminology General Symbols (idtIS7000) GB/T16273.1-1996 Graphical Symbols for Equipment Graphical Symbol Representation Planning Graphical Symbols for Equipment Part 1, Formation of Graphical Symbols GB/T 16902.1-1997 (eqv IS0 3461-1:1988) 3 Terms and Conditions Terms and Conditions used in this standard in relation to graphic symbols shall be in accordance with the provisions of GB/T15565, and terms and conditions related to welding shall be in accordance with the provisions of GB/T 2900, 22 and GB/T 3375. 4 Graphic symbols
General symbols for welding equipment are shown in Table 1.
5 Application
5.1 The application of graphic symbols shall comply with the provisions of Chapter 7 of GB/T 16902.1--1997. 5.2 The graphic symbols in Table 1 shall be enlarged or reduced in proportion. 5.3 The superscripts around the graphic symbols in Table 1 do not constitute the content of the graphic symbols, but are only the basis for symbol reproduction and application. 5.4 The general symbols for welding equipment shall be used in conjunction with GB/16273.1, and the graphic symbols for electrical equipment shall be used in conjunction with GB/T5465.2.
Approved by the State Administration of Quality and Technical Supervision on May 8, 1999 and implemented on September 1, 1999
National symbols
GB/T16273 3—1999
Table 1 General symbols for electric welding equipment
manual metal are welding electrode halder
MIG/MAG torch
TIG tarch
welding
manual metal arc welding
IS0 7000(0163)
IS) 700(0464)
1507000(0465)
IS0 7000(0456)
IS0 7000(0460)
Melt Indicative Gas Shielding/Melt Active Gas ShieldingS0700(0461)
MIG/MAGWeiding
*The content in the description column is the symbol number corresponding to the symbol in ISD 7000, indicating that the symbol is equivalent to the corresponding special number in ISO 7000. The same applies below.
GB/T 16273. 3—1999
Table 1 (continued)
Alternative inert gas welding
TIG welding
Arc spot welding
Arc spot welding
MIC/MAG spot welding
TIG spot welding
IS0 7000(04623
1S0 750004683
1507000(04697
1S0 7000(0470)
Time of welding according to inert gas protection/melting active gas protection!1S0 7000(0829) MIG/MAG spot welding with time control TIG spot welding with time control 150 7000(0830) Graphic symbol GB/T16273.3—1999 Table 1 (continued) Short circuit transfer Dip transfer Apray transfer Pulse transfer Pulse transfer Re-entry welding Intermittent welding Internittent welding Weld with reduced initial and final current ISO 7C00(0471)
IS070800472)
1SD 7000(0473)
IS7000(0831)
S07000(0832)
1S0700c(0833)
Symbol
GB/T 16273. 31999
Table 1(continued)
igtiriop
contact ignition
arc ignition by rontact
high frequency ignition
i arc ignitian by high frequency
wire feed trive
wire continuous feeding
wrire feed drive +continuoug wire feed drive .interrupted wire feed drive
1S07000(0492)
IS)7000(0475)
[50700010476】
IS0 7000(0823)
ISO 7060(0824)
1SO7000(0825)
GB/T16273.3—1999
Table (continued)
subnerged arc welding
hopper (powder or welding flux)
purging air (by gas)
i purging air (by gas)
welding torch carrier
ghs aupply
connection
workpiece connection
150 7000(0467)
ISO 7000(0466)
150 7000(0474)
1S0 7000(0451)
ISO 7000(0452)
ISO7000(0453)
GB/T 16273. 3—1999
Table 1 (continued)
Plasma welding torch
Plasma welding
Plasma cutting
Plasma catring
Plasma gas flow
+ plasma gas
Plasma shielding gas
I plasma shielding Ras
I plasma welding torch electrode
I plasma welding conrectian to electrode
ISO) 7000(0477)
ISO 7000(0478)
IS7000(0479)
IS)7000(0480)
150 7000(0481
150 7000(0182)
Graphical Symbols
GB/T 16273. 3-1999
Table 1 (continued)
Connection to plasma torch nozzle
1IS0 7000(0483)
plasnatorch connection to nozzle (positive gupply)
pilotare
transferred arc
transferred arc
Non-transfeed
Non-transfeed are
coordinate tracing
peak voltage
1501 7000<0826)
1S0 7000<0827)
ISO7000(082H)
IS0 7000(0493)
IS0 7000(0821)
GB/T16273.3—1999
Yuan Lu)
drooping valtage characteristic.substantialiy level valtage characteristiccurrent rise
current slope in
current
currentaopeaut
double stroke electric spot welding
resistance apot welding +double stroke spot welding.single spot welding
spot wrclding+bingle spot welding
1S13 7000(0454)
1S07000(0455)
1S0 7000(0458)
IS0 7000(0822)
[SO 70GC<0834]
150 760050835)
graphic symbol
GB/T 16273. 3—1999
Table 1 (continued)
Spor welding, repeat spot welding
Seam welding with interrupted current
Cantinuous seam weldinglContinuous-cur-rent stam welding
Squeeze time
Weld currenttitne
Hold time
IS0) 7000(0836)
1S0 7060(0837)
1S07000(0838)
150) T000(0839)
1SO 7000(0840)
IS0 7000(0841)
GB/T 16273. 3 -1999
Table 1 (continued)
off time
cyelewithoutwelding currentcycle with welding curtent
elamping withoutwelding
minimum pressure approachwith mininnum force
welding with constant force
SO 7000(C842)
ISO 7000(0357)
ISO 7000(0858)
1S0 7000(0843>
ISO7000(0844)
1S0 7000(0815)3-1999
Table 1 (continued)
Connection to plasma torch nozzle
1IS0 7000(0483)
plasnatorch connection to nozzle (positive gupply)
pilotare
transferred arc
transferred arc
Non-transfeed are
Coordinale tracing
Peak voltage
1501 7000<0826)
1S0 7000<0827)
ISO7000(082H)
IS0 7000(0493)
IS0 7000(0821)
GB/T16273.3—1999
Yuan Lu)
drooping valtage characteristic.flat characteristic
substantialiy level valtage characteristiccurrent rise
current slope in
current under
current over
double stroke spot welding
resistance apot welding +double stroke spot welding.single spot welding
Spot wrclding+Bingle spot welding
1S13 7000(0454)
1S07000(0455)
1S0 7000(0458)
IS0 7000(0822)
[SO 70GC<0834]
150 760050835)
Graphical symbols
GB/T 16273. 3—1999
Table 1 (continued)
spor welding, repeat spot welding
spor welding, repeat spot welding
spor welding, repeat spot welding
spor welding, repeat spot welding
spor welding with interrupted current
spor welding with interrupted current
cantinuous seam weldingl continuous-cur-rent stam welding
squeeze time
energization time
weld currenttitne
holding time
half time
IS0) 7000(0836)
1S0 7060(0837)
1S07000(0838)
150) T000(0839)
1SO 7000(0840)
IS0 7000(0841)
GB/T 16273. 3 -1999
Table 1 (continued)
off time
off time
cyelewithoutwelding currentcycle with welding curtent
elamping withoutwelding
approachwith mininnum force
Welding with constant force
SO 7000(C842)
ISO 7000(0357)
ISO 7000(0858)
1S0 7000(0843>
ISO7000(0844)
1S0 7000(0815)3-1999
Table 1 (continued)
Connection to plasma torch nozzle
1IS0 7000(0483)bzxZ.net
plasnatorch connection to nozzle (positive gupply)
pilotare
transferred arc
transferred arc
Non-transfeed are
Coordinale tracing
Peak voltage
1501 7000<0826)
1S0 7000<0827)
ISO7000(082H)
IS0 7000(0493)
IS0 7000(0821)
GB/T16273.3—1999
Yuan Lu)
drooping valtage characteristic.flat characteristic
substantialiy level valtage characteristiccurrent rise
current slope in
current under
current over
double stroke spot welding
resistance apot welding +double stroke spot welding.single spot welding
Spot wrclding+Bingle spot welding
1S13 7000(0454)
1S07000(0455)
1S0 7000(0458)
IS0 7000(0822)
[SO 70GC<0834]
150 760050835)
Graphical symbols
GB/T 16273. 3—1999
Table 1 (continued)
spor welding, repeat spot welding
spor welding, repeat spot welding
spor welding, repeat spot welding
spor welding, repeat spot welding
spor welding with interrupted current
spor welding with interrupted current
cantinuous seam weldingl continuous-cur-rent stam welding
squeeze time
energization time
weld currenttitne
holding time
half time
IS0) 7000(0836)
1S0 7060(0837)
1S07000(0838)
150) T000(0839)
1SO 7000(0840)
IS0 7000(0841)
GB/T 16273. 3 -1999
Table 1 (continued)
off time
off time
cyelewithoutwelding currentcycle with welding curtent
elamping withoutwelding
approachwith mininnum force
Welding with constant force
SO 7000(C842)
ISO 7000(0357)
ISO 7000(0858)
1S0 7000(0843>
ISO7000(0844)
1S0 7000(0815)3 -1999
Table 1 (continued)
off time
cyelewithoutwelding current
cycle with welding curtent
elamping withoutwelding
approachwithminimumforce
weldingwithconstantforce
ISO 7000(C842)
ISO 7000(0357)
ISO 7000(0858)
1S0 7000(0843>
ISO7000(0844)
1S0 7000(0815)3 -1999
Table 1 (continued)
off time
cyelewithoutwelding current
cycle with welding curtent
elamping withoutwelding
approachwithminimumforce
weldingwithconstantforce
ISO 7000(C842)
ISO 7000(0357)
ISO 7000(0858)
1S0 7000(0843>
ISO7000(0844)
1S0 7000(0815)
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.