Some standard content:
Ics55.160
National Standard of the People's Republic of China
GH/T 19786—2005
Testing Procedure for Wooden Packaging Containers
Inspeetion code for wooden containcrs2005-05-25 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
2005-11-01 Implementation
This standard is a normative appendix, and appendix A is a confidential appendix. This standard is jointly issued by China National Packaging Corporation. The standard is issued by the National Packaging Standardization Committee of China, and the original units of this standard are the Commodity Packaging Research Institute and the Mechanical Engineering Research Institute. The participants of this standard are: China Academy of Sciences, the Packaging Office of the People's Liberation Army, and the Ministry of Science and Technology Research Institute. The main drafters: Tu Yuanmei, Huang Gu, Li Shihua, Zhang Jin, Guo Baohua. GB/T19786—2005
1 Test Procedure for Wood Packaging Containers
GD/T 107B6—2005
This standard specifies the inspection classification of quality packaging containers, as well as the inspection items, inspection selection and inspection content, and provides sampling and qualified semi-final specifications.bzxZ.net
This standard specifies the applicable technical specifications for the quality inspection of packaging containers.2 Normative References
The following documents have become the series of this standard through the introduction of this standard. They are referenced documents with the date indicated. All revisions (excluding errors) or subsequent editions after their effective date do not apply to this standard. However, the parties who have reached an agreement with this standard may study whether the latest editions of these documents can be used. For undated referenced documents, the updated version shall apply to this standard. GB/T 13/T 2628.-GB/T 4857.-3GB/T 4857. *-GB/T 48E7. 2GT/T 4857.aK/T 4=?, 4G13/T J657.5G3/T 4257.6GB:T 4657.7GB/T 4857. 9GB/T 4857.-3GB/T 4857. *-GB/T 4$57. 12
GR/T 48:7.14
KT 4857. 15
GR/T 1837. J6
G3/T 4hs. 17
GR/T 4852.18
G3/T 48s*.311
GB/T 4657. 23
GB/T ESS8
GB/T 6358
GR:T 774
Efficient assembly according to the order
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging
Transportation packaging Packing characteristics
Pulled packaging
Reverse transportation packaging
Transportation additional packaging
Transportation sample
Transportation braided packaging
Transportation temporary packaging
Total packaging
Part 1 Acceptance quality limit (AQ) inspection Batch inspection Sample drawing plan Test of each part of the corresponding standard non-piece method
Wetness adjustment treatment
Front load stacking test method
Pressure test method
Yaoyouminlinfang
Flowing test method
Positive density fixed frequency dynamic test method
Responsibility test method
Positive variable data test method
Horizontal impact test method
Lingshui test method
Baizhu test method
Controlled horizontal impact test method
Stacking test method using hydraulic or testing machine Comprehensive energy principle
Compilation of energy outline data
Controlled test method
Random sub-direct reporting test method
Six types of transport packaging test method
Transport inspection package delivery and collection mark
Constant specification wooden box
GB/T S846. 4
GH/1 1a8*9
Not judged||G15/T12464
Ordinary wood
General technical conditions for ordinary composite board
(3/12126.2 Technical requirements for geological shrimp board GB/T 13-23
GB/T -3-44
Lemon woven plywood
Packing
Bamboo cabinet
GB/T19/86—2005
GR/T :8924
Xiangsi test push box
Submarine box
GB/TS2
Packing equipment metal test accessories
GB/T8327
3 Inspection classification
Technical quality packaging products acceptance general inspection and performance inspection. Generally, the inspection is mainly for the material, structure and size of the wooden packaging container, and the process should be carried out according to the standards or design regulations.
The performance inspection is mainly for the wooden packaging container and other components in the circulation process. The acceptance can be subjected to the environment and hazards of the vehicle through the simulated flow or the assumed operation inspection,
4 Age inspection
The performance inspection items of small quality packaging containers are daily packaging stores, pole grids, structures and other items. Unless otherwise specified, the general inspection samples shall be in accordance with Appendix A, as specified. 4.1 Materials 4.1.1 Moisture content of wood The method for determining the moisture content of each material shall comply with the provisions of 3/T131, or use a wood moisture meter to determine the moisture content of each component of the container. The moisture content of wood and pillows shall not exceed 25%. The moisture content of other components shall not exceed 20%. 4.1.2 Materials The inspection items, inspection contents and inspection methods for the quality of packaging containers are shown in Tables 1 and 2. Table 1 Inspection items, inspection contents and inspection methods for materials used for packaging containers Inspection items All materials should not be underestimated. The requirements are not allowed to be underestimated. Long bull does not suffer from a single, the average stock is not Li in a single, must be safe, Zhang full of goods busy reward request only give up toe management, etc. see the attached table,
subject to point closure is not allowed at any time, · generally release the component design light feel trust for a long time there are A spots and displacement ready-made unknown contribution rate
component inappropriate locking effect subject to 10, large
force potential component danger blood allowed to discuss the planning section, a total of other parts of the tax allowed each, three long centers are not, into, heart
general components allowed diameter pet life and diameter people The material is 25, the straight small T5mm section.
allows the material to be safe along the change of direction in the degree not more than 20%, a whole component stress structure allows the study of the sensitivity of the material to study the degree of 30%, the degree of the matter, generally allow the village and the wide world, the degree of
and the shape of the direction (not 1, a component is not
than 25)
Sichuan Wei or still in the insertion of the popular research and color change of the parts, the parts of the material good, if it is significantly reduced, can be determined as away, 2|| tt||Structure and size
Table 2 Inspection items and inspection methods for wood packaging containers Inspection items
Combination
Inspection method
CB/T19786—2005
Specification of GR/TJ846.4
Standard of GR/T12626.2
Inspection items and inspection methods for the structure and size of wooden packaging containers are as follows: Table 3 Inspection items, inspection contents and inspection methods for the structure and size of packaging containers Inspection content General technical specifications Standard wire tie-down device According to the specifications of the packaging container Non-standard technical analysis Please make the size according to 4.3 Processing technology (D/T12* According to the provisions of 28 According to the provisions of (.B:1 18125 According to the provisions of (+B/T 1H14 According to the design requirements To be used: mm 20-1cn Allowable error/mm Packing container design.1 Drug inspection month, inspection content and inspection method are shown in Table 1. Table 4 Inspection items, inspection contents and inspection methods of wooden packaging containers. Inspection objectives
Conclusion
And, parts docking
Meeting point
Ventilation point
Water point
Hazardous materials inspection
1 Continued. The form of the connection shall be determined by the design drawing, and the connection shall be made according to the standard or design drawing. 3. For the size and quantity of the design drawing, the table does not include the stitching head and nail tip, and the detailed connection of the board should be in accordance with the provisions of GB/T18927 or the design drawing, and the provisions of R/T7284. The material should be free of pollution. The network indication should be in accordance with the provisions of /T1SI. The design orientation should be in accordance with the provisions of the design type and the measurement test method should be GB/T19786-2C05. 5 Performance inspection: The quality inspection items of the container include the required inspection items and optional items. The mandatory items and optional items are mainly determined by the benefits of wooden packaging, the availability of packaging and the circulation environment conditions. 5. Performance inspection items and inspection methods for wooden packaging containers. Inspection and acceptance methods for wooden packaging containers. GH, A57, y. Title drop test. Horizontal impact test. Energy verification test. Record hanging test. Water-saving test. Mobile fire test. This test should be carried out according to the following conditions: K/T 4857, 16. GN/T 4%57. 4. GT 4857. 5. C/T539E. GB/T 4657. 15. GB/T 4#57.20
GB/C 5398
GR/T 45.H
GB/T -BE7, 12
G3/t483.5
G:T 1857. 10
G1 -E57.23
GE/T4337.G
GD VT ST.H
Non-state ten narrow
No other weight/kg
! , must be controlled: according to the need to reverse the rate of the subject, wire 2: This package pick through the performance test busy preparation ndu
) 1, K/14857, 18 end system of the test large or reported in accordance with the specification of the material can be prepared to test the light sample 1) connect [H4Y. of the current provisions, the test sample service department to make a large vehicle,
Steel through the tie pin
(content blood: kg)
system according to the characteristics of the consultation device and no oil In the process of recording the bad environment, change C1/II 1857.2 to the specified road * the measured parts are pre-pressed, the test conditions and regulations of the sample are as follows: the test is for inspection, G4857.3 is not adopted. G/495.15 is optional: the surface size of the Milo device is pushed to the height according to the small amount of length and side amount. When the period is not less than 1, the inspection is a necessary item, and the sampling and content are determined according to the inspection standard or the contract. If the standard or contract time is not specified, it shall be determined according to the screening record. A. 1 Introduction
Appendix A
(Normative Appendix)
Sampling and qualification judgment
The method specified in the standard or contract shall be in accordance with the provisions of the following provisions. A2 Sampling
GB/T 19786—2005
The sampling method for external inspection shall be in accordance with the provisions of the non-fixed sampling plan in 6B/T 2H28.1: The sampling quantity is as follows A1
The sampling efficiency of performance inspection is generally not more than 3 items, Table A 1 Sampling efficiency of appearance inspection of wooden packaging containers -150
251--509
Note, sample I, the items in the table are not suitable for this category, or the price is lower, the average cost, the monthly cost, suitable for a certain situation, suitable for a single environment for users to install and disassemble items, or the price is relatively high. A.3 Judgment of unacceptable appearance inspection
4,3.1 This product complies with the standard or is set in the book, and the length can meet the requirements of the new quality cover
A,3.2 The dangerous section of the main force-bearing structure (post position) has an unacceptable depression: the basic internal energy of the direct displacement shape of the final quality position is small, A.3.3 The actual situation does not meet the requirements.
%. Judgment of acceptable performance inspection
A.4.1 According to Table A, for the test samples of Group I, there is no damage or leakage inside, and the packaging container is allowed to be damaged. A.4.2 According to Table A: for the test samples of Group II, there is no damage or leakage inside, and the packaging container is allowed to be slightly damaged. 4.4.3 According to Table A., for the test samples of Group II, the contents are intact and there is no leakage. , packaging machine allows scratches, GB/T13786-2005
(Informative Appendix)
Pretreatment methods and requirements for wooden packaging containers and the methods and requirements for non-pressurized packaging containers, late warehouse report, check board, roaring material and other materials as the essential packaging container material, no need to select treatment, but should use the recent production, the general standard treatment is within 1 month.
The wood used as packaging material should first be isolated, and then sterilized, treated or treated with water. Health, 7 Temporary treatment
Including heat treatment and solution treatment. Temporary treatment should be within 2 days before leaving the shore, but temporary treatment can kill the original plan! Some cities are more concerned about preventing secondary pollution of wood, B, 2.1 Heat treatment required
Environmentally friendly agents should be used, such as methane treatment wood, in accordance with the provisions of Part II.1 and Table B.1.
Natural sea water:
.1.-15
6.-10
Note 1: For temperatures below 200 °C, the requirements for methane treatment water are not applicable.
The steaming time
is generally limited to 2: or the time specified in the table is a general limitation, which may be determined based on the needs of the technical performance. B.2.2
Disinfection treated wood should be subjected to accelerated drying (such as drying or drying) to reduce the moisture content of the wood to less than 12%, and then subjected to high temperature treatment of the structure: see Table 11.2. Heat treatment must be carried out in a sterilizer. The temperature must not be lower than 74°C. Table B.2 Requirements for heat treatment 1.2.3 Durable treatment This treatment can be used as a long-term insecticide for packaging products (including wooden packaging) to prevent insect contamination in the long term. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified before use and must be Those antiseptics that can be fixed in the wood and whose chemical composition does not change are anti-corrosion agents. They are anti-corrosion agents. The anti-corrosion agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-corrosion agents. Water-soluble anti-corrosion agents mainly include CCA (CCA) preservatives, AQS (Ammonia) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.The material defects shall be in accordance with the provisions of /T1SI. The design direction shall be in accordance with the provisions of the design type. The measurement and test methods shall be GB/T19786-2C05. 5 Performance test The inspection items of the quality container include the mandatory and optional items. The mandatory and optional items are mainly determined by the properties of the wooden packaging and the quality of the packaging and the circulation environment. 5. Performance inspection items and inspection methods for wooden packaging containers. Inspection and acceptance methods for wooden packaging containers. GH, A57, y. Title drop test. Horizontal impact test. Energy verification test. Record hanging test. Water-saving test. Mobile fire test. This test should be carried out according to the following conditions: K/T 4857, 16. GN/T 4%57. 4. GT 4857. 5. C/T539E. GB/T 4657. 15. GB/T 4#57.20
GB/C 5398
GR/T 45.H
GB/T -BE7, 12
G3/t483.5
G:T 1857. 10
G1 -E57.23
GE/T4337.G
GD VT ST.H
Non-state ten narrow
No other weight/kg
! , must be controlled: according to the need to reverse the rate of the subject, wire 2: This package pick through the performance test busy preparation ndu
) 1, K/14857, 18 end system of the test large or reported in accordance with the specification of the material can be prepared to test the light sample 1) connect [H4Y. of the current provisions, the test sample service department to make a large vehicle,
Steel through the tie pin
(content blood: kg)
system according to the characteristics of the consultation device and no oil In the process of recording the bad environment, change C1/II 1857.2 to the specified road * the measured parts are pre-pressed, the test conditions and regulations of the sample are as follows: the test is for inspection, G4857.3 is not adopted. G/495.15 is optional: the surface size of the Milo device is pushed to the height according to the small amount of length and side amount. When the period is not less than 1, the inspection is a necessary item, and the sampling and content are determined according to the inspection standard or the contract. If the standard or contract time is not specified, it shall be determined according to the screening record. A. 1 Introduction
Appendix A
(Normative Appendix)
Sampling and qualification judgment
The method specified in the standard or contract shall be in accordance with the provisions of the following provisions. A2 Sampling
GB/T 19786—2005
The sampling method for external inspection shall be in accordance with the provisions of the non-fixed sampling plan in 6B/T 2H28.1: The sampling quantity is as follows A1
The sampling efficiency of performance inspection is generally not more than 3 items, Table A 1 Sampling efficiency of appearance inspection of wooden packaging containers -150
251--509
Note, sample I, the items in the table are not suitable for this category, or the price is lower, the average cost, the monthly cost, suitable for a certain situation, suitable for a single environment for users to install and disassemble items, or the price is relatively high. A.3 Judgment of unacceptable appearance inspection
4,3.1 This product complies with the standard or is set in the book, and the length can meet the requirements of the new quality cover
A,3.2 The dangerous section of the main force-bearing structure (post position) has an unacceptable depression: the basic internal energy of the direct displacement shape of the final quality position is small, A.3.3 The actual situation does not meet the requirements.
%. Judgment of acceptable performance inspection
A.4.1 According to Table A, for the test samples of Group I, there is no damage or leakage inside, and the packaging container is allowed to be damaged. A.4.2 According to Table A: for the test samples of Group II, there is no damage or leakage inside, and the packaging container is allowed to be slightly damaged. 4.4.3 According to Table A., for the test samples of Group II, the contents are intact and there is no leakage. , packaging machine allows scratches, GB/T13786-2005
(Informative Appendix)
Pretreatment methods and requirements for wooden packaging containers and the methods and requirements for non-pressurized packaging containers, late warehouse report, check board, roaring material and other materials as the essential packaging container material, no need to select treatment, but should use the recent production, the general standard treatment is within 1 month.
The wood used as packaging material should first be isolated, and then sterilized, treated or treated with water. Health, 7 Temporary treatment
Including heat treatment and solution treatment. Temporary treatment should be within 2 days before leaving the shore, but temporary treatment can kill the original plan! Some cities are more concerned about preventing secondary pollution of wood, B, 2.1 Heat treatment required
Environmentally friendly agents should be used, such as methane treatment wood, in accordance with the provisions of Part II.1 and Table B.1.
Natural sea water:
.1.-15
6.-10
Note 1: For temperatures below 200 °C, the requirements for methane treatment water are not applicable.
The steaming time
is generally limited to 2: or the time specified in the table is a general limitation, which may be determined based on the needs of the technical performance. B.2.2
Disinfection treated wood should be subjected to accelerated drying (such as drying or drying) to reduce the moisture content of the wood to less than 12%, and then subjected to high temperature treatment of the structure: see Table 11.2. Heat treatment must be carried out in a sterilizer. The temperature must not be lower than 74°C. Table B.2 Requirements for heat treatment 1.2.3 Durable treatment This treatment can be used as a long-term insecticide for packaging products (including wooden packaging) to prevent insect contamination in the long term. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified before use and must be Those antiseptics that can be fixed in the wood and whose chemical composition does not change are anti-corrosion agents. They are anti-corrosion agents. The anti-corrosion agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-corrosion agents. Water-soluble anti-corrosion agents mainly include CCA (CCA) preservatives, AQS (Ammonia) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.The material defects shall be in accordance with the provisions of /T1SI. The design direction shall be in accordance with the provisions of the design type. The measurement and test methods shall be GB/T19786-2C05. 5 Performance test The inspection items of the quality container include the mandatory and optional items. The mandatory and optional items are mainly determined by the properties of the wooden packaging and the quality of the packaging and the circulation environment. 5. Performance inspection items and inspection methods for wooden packaging containers. Inspection and acceptance methods for wooden packaging containers. GH, A57, y. Title drop test. Horizontal impact test. Energy verification test. Record hanging test. Water-saving test. Mobile fire test. This test should be carried out according to the following conditions: K/T 4857, 16. GN/T 4%57. 4. GT 4857. 5. C/T539E. GB/T 4657. 15. GB/T 4#57.20
GB/C 5398
GR/T 45.H
GB/T -BE7, 12
G3/t483.5
G:T 1857. 10
G1 -E57.23
GE/T4337.G
GD VT ST.H
Non-state ten narrow
No other weight/kg
! , must be controlled: according to the need to reverse the rate of the subject, wire 2: This package pick through the performance test busy preparation ndu
) 1, K/14857, 18 end system of the test large or reported in accordance with the specification of the material can be prepared to test the light sample 1) connect [H4Y. of the current provisions, the test sample service department to make a large vehicle,
Steel through the tie pin
(content blood: kg)
system according to the characteristics of the consultation device and no oil In the process of recording the bad environment, change C1/II 1857.2 to the specified road * the measured parts are pre-pressed, the test conditions and regulations of the sample are as follows: the test is for inspection, G4857.3 is not adopted. G/495.15 is optional: the surface size of the Milo device is pushed to the height according to the small amount of length and side amount. When the period is not less than 1, the inspection is a necessary item, and the sampling and content are determined according to the inspection standard or the contract. If the standard or contract time is not specified, it shall be determined according to the screening record. A. 1 Introduction
Appendix A
(Normative Appendix)
Sampling and qualification judgment
The method specified in the standard or contract shall be in accordance with the provisions of the following provisions. A2 Sampling
GB/T 19786—2005
The sampling method for external inspection shall be in accordance with the provisions of the non-fixed sampling plan in 6B/T 2H28.1: The sampling quantity is as follows A1
The sampling efficiency of performance inspection is generally not more than 3 items, Table A 1 Sampling efficiency of appearance inspection of wooden packaging containers -150
251--509
Note, sample I, the items in the table are not suitable for this category, or the price is lower, the average cost, the monthly cost, suitable for a certain situation, suitable for a single environment for users to install and disassemble items, or the price is relatively high. A.3 Judgment of unacceptable appearance inspection
4,3.1 This product complies with the standard or is set in the book, and the length can meet the requirements of the new quality cover
A,3.2 The dangerous section of the main force-bearing structure (post position) has an unacceptable depression: the basic internal energy of the direct displacement shape of the final quality position is small, A.3.3 The actual situation does not meet the requirements.
%. Judgment of acceptable performance inspection
A.4.1 According to Table A, for the test samples of Group I, there is no damage or leakage inside, and the packaging container is allowed to be damaged. A.4.2 According to Table A: for the test samples of Group II, there is no damage or leakage inside, and the packaging container is allowed to be slightly damaged. 4.4.3 According to Table A., for the test samples of Group II, the contents are intact and there is no leakage. , packaging machine allows scratches, GB/T13786-2005
(Informative Appendix)
Pretreatment methods and requirements for wooden packaging containers and the methods and requirements for non-pressurized packaging containers, late warehouse report, check board, roaring material and other materials as the essential packaging container material, no need to select treatment, but should use the recent production, the general standard treatment is within 1 month.
The wood used as packaging material should first be isolated, and then sterilized, treated or treated with water. Health, 7 Temporary treatment
Including heat treatment and solution treatment. Temporary treatment should be within 2 days before leaving the shore, but temporary treatment can kill the original plan! Some cities are more concerned about preventing secondary pollution of wood, B, 2.1 Heat treatment required
Environmentally friendly agents should be used, such as methane treatment wood, in accordance with the provisions of Part II.1 and Table B.1.
Natural sea water:
.1.-15
6.-10
Note 1: For temperatures below 200 °C, the requirements for methane treatment water are not applicable.
The steaming time
is generally limited to 2: or the time specified in the table is a general limitation, which may be determined based on the needs of the technical performance. B.2.2
Disinfection treated wood should be subjected to accelerated drying (such as drying or drying) to reduce the moisture content of the wood to less than 12%, and then subjected to high temperature treatment of the structure: see Table 11.2. Heat treatment must be carried out in a sterilizer. The temperature must not be lower than 74°C. Table B.2 Requirements for heat treatment 1.2.3 Durable treatment This treatment can be used as a long-term insecticide for packaging products (including wooden packaging) to prevent insect contamination in the long term. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified before use and must be Those antiseptics that can be fixed in the wood and whose chemical composition does not change are anti-corrosion agents. They are anti-corrosion agents. The anti-corrosion agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-corrosion agents. Water-soluble anti-corrosion agents mainly include CCA (CCA) preservatives, AQS (Ammonia) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.The current regulations, the test should be conducted by the service department through the large vehicle,
steel clamping pin
(content blood: kg)
according to the characteristics of the equipment and the oil-free process environment recording parts, change C1/II 1857.2 to determine the measurement of the parts to be pre-treated, too independent production and packaging samples of this guide and regulations for transportation test conditions are in accordance with the regulations, Lan: test for inspection, not adopted G4857.3. G/495.15 optional light: Milo device can be pushed to the high side size according to the small amount of long side amount of not less than 1, let the test as a necessary item, sampling and content judgment
according to the inspection analysis of the standards or the provisions of the contract, if the standard or contract time is not specified, according to the screening record of the view, A. 1 Appendix A (Normative Appendix) Sampling and Qualification Judgment The method of sampling and acceptance shall be as follows: A2 Sampling GB/T 19786—2005 The sampling method for external inspection shall be as specified in 6B/T 2H28.1. The sampling efficiency of performance inspection is generally not more than 3 items, Table A 1 Sampling efficiency of appearance inspection of wooden packaging containers 26-50 51-96 9 -150
251--509
Note, sample I, the items in the table are not suitable for this category, or the price is lower, the average cost, the monthly cost, suitable for a certain situation, suitable for a single environment for users to install and disassemble items, or the price is relatively high. A.3 Judgment of unacceptable appearance inspection
4,3.1 This product complies with the standard or is set in the book, and the length can meet the requirements of the new quality cover
A,3.2 The dangerous section of the main force-bearing structure (post position) has an unacceptable depression: the basic internal energy of the direct displacement shape of the final quality position is small, A.3.3 The actual situation does not meet the requirements.
%. Judgment of acceptable performance inspection
A.4.1 According to Table A, for the test samples of Group I, there is no damage or leakage inside, and the packaging container is allowed to be damaged. A.4.2 According to Table A: for the test samples of Group II, there is no damage or leakage inside, and the packaging container is allowed to be slightly damaged. 4.4.3 According to Table A., for the test samples of Group II, the contents are intact and there is no leakage. , packaging machine allows scratches, GB/T13786-2005
(Informative Appendix)
Pretreatment methods and requirements for wooden packaging containers and the methods and requirements for non-pressurized packaging containers, late warehouse report, check board, roaring material and other materials as the essential packaging container material, no need to select treatment, but should use the recent production, the general standard treatment is within 1 month.
The wood used as packaging material should first be isolated, and then sterilized, treated or treated with water. Health, 7 Temporary treatment
Including heat treatment and solution treatment. Temporary treatment should be within 2 days before leaving the shore, but temporary treatment can kill the original plan! Some cities are more concerned about preventing secondary pollution of wood, B, 2.1 Heat treatment required
Environmentally friendly agents should be used, such as methane treatment wood, in accordance with the provisions of Part II.1 and Table B.1.
Natural sea water:
.1.-15
6.-10
Note 1: For temperatures below 200 °C, the requirements for methane treatment water are not applicable.
The steaming time
is generally limited to 2: or the time specified in the table is a general limitation, which may be determined based on the needs of the technical performance. B.2.2
Disinfection treated wood should be subjected to accelerated drying (such as drying or drying) to reduce the moisture content of the wood to less than 12%, and then subjected to high temperature treatment of the structure: see Table 11.2. Heat treatment must be carried out in a sterilizer. The temperature must not be lower than 74°C. Table B.2 Requirements for heat treatment 1.2.3 Durable treatment This treatment can be used as a long-term insecticide for packaging products (including wooden packaging) to prevent insect contamination in the long term. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified before use and must be Those antiseptics that can be fixed in the wood and whose chemical composition does not change are anti-corrosion agents. They are anti-corrosion agents. The anti-corrosion agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-corrosion agents. Water-soluble anti-corrosion agents mainly include CCA (CCA) preservatives, AQS (Ammonia) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.The current regulations, the test should be conducted by the service department through the large vehicle,
steel clamping pin
(content blood: kg)
according to the characteristics of the equipment and the oil-free process environment recording parts, change C1/II 1857.2 to determine the measurement of the parts to be pre-treated, too independent production and packaging samples of this guide and regulations for transportation test conditions are in accordance with the regulations, Lan: test for inspection, not adopted G4857.3. G/495.15 optional light: Milo device can be pushed to the high side size according to the small amount of long side amount of not less than 1, let the test as a necessary item, sampling and content judgment
according to the inspection analysis of the standards or the provisions of the contract, if the standard or contract time is not specified, according to the screening record of the view, A. 1 Appendix A (Normative Appendix) Sampling and Qualification Judgment The method of sampling and acceptance shall be as follows: A2 Sampling GB/T 19786—2005 The sampling method for external inspection shall be as specified in 6B/T 2H28.1. The sampling efficiency of performance inspection is generally not more than 3 items, Table A 1 Sampling efficiency of appearance inspection of wooden packaging containers 26-50 51-96 9 -150
251--509
Note, sample I, the items in the table are not suitable for this category, or the price is lower, the average cost, the monthly cost, suitable for a certain situation, suitable for a single environment for users to install and disassemble items, or the price is relatively high. A.3 Judgment of unacceptable appearance inspection
4,3.1 This product complies with the standard or is set in the book, and the length can meet the requirements of the new quality cover
A,3.2 The dangerous section of the main force-bearing structure (post position) has an unacceptable depression: the basic internal energy of the direct displacement shape of the final quality position is small, A.3.3 The actual situation does not meet the requirements.
%. Judgment of acceptable performance inspection
A.4.1 According to Table A, for the test samples of Group I, there is no damage or leakage inside, and the packaging container is allowed to be damaged. A.4.2 According to Table A: for the test samples of Group II, there is no damage or leakage inside, and the packaging container is allowed to be slightly damaged. 4.4.3 According to Table A., for the test samples of Group II, the contents are intact and there is no leakage. , packaging machine allows scratches, GB/T13786-2005
(Informative Appendix)
Pretreatment methods and requirements for wooden packaging containers and the methods and requirements for non-pressurized packaging containers, late warehouse report, check board, roaring material and other materials as the essential packaging container material, no need to select treatment, but should use the recent production, the general standard treatment is within 1 month.
The wood used as packaging material should first be isolated, and then sterilized, treated or treated with water. Health, 7 Temporary treatment
Including heat treatment and solution treatment. Temporary treatment should be within 2 days before leaving the shore, but temporary treatment can kill the original plan! Some cities are more concerned about preventing secondary pollution of wood, B, 2.1 Heat treatment required
Environmentally friendly agents should be used, such as methane treatment wood, in accordance with the provisions of Part II.1 and Table B.1.
Natural sea water:
.1.-15
6.-10
Note 1: For temperatures below 200 °C, the requirements for methane treatment water are not applicable.
The steaming time
is generally limited to 2: or the time specified in the table is a general limitation, which may be determined based on the needs of the technical performance. B.2.2
Disinfection treated wood should be subjected to accelerated drying (such as drying or drying) to reduce the moisture content of the wood to less than 12%, and then subjected to high temperature treatment of the structure: see Table 11.2. Heat treatment must be carried out in a sterilizer. The temperature must not be lower than 74°C. Table B.2 Requirements for heat treatment 1.2.3 Durable treatment This treatment can be used as a long-term insecticide for packaging products (including wooden packaging) to prevent insect contamination in the long term. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified before use and must be Those antiseptics that can be fixed in the wood and whose chemical composition does not change are anti-corrosion agents. They are anti-corrosion agents. The anti-corrosion agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-corrosion agents. Water-soluble anti-corrosion agents mainly include CCA (CCA) preservatives, AQS (Ammonia) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.3 Durable treatment
It can be used as a long-term protection for packaging products (including wooden packaging) against moisture and contamination: This treatment can prevent insects from attacking the material for a long time. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified and must be those that can be fixed in the wood and whose chemical composition does not change, that is, anti-corrosion.
The anti-friction agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-friction agents. Water-soluble anti-friction agents mainly include CCA (CCA) preservatives, AQS (AQS) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.3 Durable treatment
It can be used as a long-term protection for packaging products (including wooden packaging) against moisture and contamination: This treatment can prevent insects from attacking the material for a long time. It is suitable for packaging that can be reused or needs to be stored for a long time. The preservative used for permanent treatment must be certified and must be those that can be fixed in the wood and whose chemical composition does not change, that is, anti-corrosion.
The anti-friction agents that meet the requirements can be divided into water-soluble anti-wear agents and non-water-soluble anti-friction agents. Water-soluble anti-friction agents mainly include CCA (CCA) preservatives, AQS (AQS) preservatives, and Cu2O3 (Cu2O3) preservatives. 3 Matters needing attention
Wood treatment involves S-type corrosion inhibitors. Countries around the world are highly concerned about this, but there are differences in the specific requirements. In specific employment practices, the requirements of the ordering party should be formulated and the certification of the quarantine department should be obtained.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.