This standard specifies the type structure, size, requirements, test methods and inspection rules of ordinary wooden boxes. This standard applies to the design, production and inspection of ordinary wooden boxes with the sum of the inner dimensions of length, width and height below 2,600 and the contents below 200 kg. For ordinary wooden boxes exceeding the specified size and weight, it can be used as a reference. GB/T 12464-2002 Ordinary Wooden Box GB/T12464-2002 Standard Download Decompression Password: www.bzxz.net
This standard specifies the type structure, size, requirements, test methods and inspection rules of ordinary wooden boxes. This standard applies to the design, production and inspection of ordinary wooden boxes with the sum of the inner dimensions of length, width and height below 2,600 and the contents below 200 kg. For ordinary wooden boxes exceeding the specified size and weight, it can be used as a reference.

1CS 55.160
National Standard of the People's Republic of China
GB/T12464—2002
Daiyu GT14—19
Ordinary wooden box
Wooden boxes
2002-12-20 release
People's Republic of China
State Administration of Quality Supervision, Inspection and Quarantine
2003-05-01 implementation
GB:T124642002
This standard is revised in accordance with JIS Z1403:11571402 in the ordinary policy: in accordance with JIS Z1403 when the standard is adopted, full consideration is given to the characteristics of my country's material facilities, management level and transportation environment conditions, and the scientific and reasonable content of H/T 124641990, which has been proved to be suitable for China's actual conditions, is ensured. This standard is issued by China National Packaging Standardization Technical Committee, which is responsible for the classification, maximum load-bearing capacity, material quality and size of components, etc., so that it can conform to the actual situation in my country and meet the requirements of export packaging. Drafting units of the standard: Kaicheng Scientific Research Institute, Beijing Shanren Environmental Inspection and Quarantine Bureau, Beijing Hualu Road Electric Co., Ltd., Hebei Best Building Materials Co., Ltd., main authors: Zhang Xiao, Chen Qineng, Zhou Nan, Zhang Jianzhou, Dang Wo, Sichuan New 1 standard for ordinary wooden boxes. This standard specifies the types, sizes, requirements, test methods and inspection specifications of ordinary wooden boxes. CB/T 12464---20D2
This standard applies to wooden boxes with inner dimensions K, width and height less than 2600m, and contents less than 29g, without production changes and inspection. For wooden boxes with a specified length and length of more than 2 years, please refer to the reference date. 2 Normative references
The clauses in the list of references in this standard shall become the clauses of this standard. For any referenced document with a date, all subsequent revisions (excluding errors) shall not be applicable to this standard. However, all parties that have reached an agreement based on this standard are encouraged to study and produce new versions of these documents. For any referenced document without a date, the latest version shall apply. The most suitable for wood standard GB/34 general purpose medical steel nails (has been adjusted to the industry standard) GB/T19 wood moisture content determination method CB/T4173 packaging steel belt (has been adjusted to the industry standard) GBT1%5Y.3-19 packaging suitable for transport package static load stacking test method CB/T4857:1999 packaging transport package silent test method G/TH817.1-10% plywood first through cavity version general according to technical conditions GB/T133841992 3 classification machine application product packaging applicable technical parts This pin is divided into two according to the load of the contents in the container. Level 1: Mainly used when the load state of the contents in the container is medium load or the packaging requirements are high Level 2, mainly used when the load state of the contents in the container is uniform load and the requirements for packaging are not high. 4 types
General oil tanks are composed of the front, bottom and original difference. The side panels are added and the bottom and top cover are installed on the front and end panels (see Figure 1~Figure
According to the structure of the end plate and the end plate, the general oil tanks are classified according to the table [, Table 1 Classification of oil tanks
Production method of oil tanks
Gan Shutdown
Hua Luo Rice
Hua Mushroom Tao
Mao Fan Han
Main number characteristics
Monthly installation site is below 20k, the internal integrated structure is the largest of the three inner belt surfaces as a whole
inch, and is greater than 1300, and the height is not more than 2:IG: rmm one no technical disinfection
Contents below 150kg
P package below 15Ue
Package with a panel
No panel with a writing panel
GB/T124642032
Discussion of construction
Foot box
Sealing model
Flower hot marten
Bite will pass through the closed box
A3A type
Table 1 (continued)
Also used as
Contents below ke
Endocrine 59 kg with
: Type (first-bar wooden box) example
Figure 22 Type [vertical fence wooden box] example
Figure 33 Type [peach bar sticky] example
Figure 44 Type | Inner bar wooden 1 example
The inner test of the installation point
is equipped with text
special, the format can be triangular
The surface is equipped with bar and yellow
15: IB
5 Basic requirements
51 Timber particles
5..1 Timber
5.1.1.1 Types
b) 58
Figure 55 [Frame file box] Example
So the combined library
GR/T124542002
The materials used in the extended box are mainly coniferous pine, end wood, sample wood, happy wood, new wood, lotus end, etc., and some species with strong or larger moisture content are also used. 5. 1. 1 2 Moisture content
The moisture content of wood is generally the same! 20%, but the water content of export files and type 3 boxes is below 21% 5113 Defects
The limit of defects in technical materials shall be in accordance with the provisions of R/33 5.1.1.4 Dimensional deviation
When the average width of the wood is not greater than 1m. When it is greater than 2, the deviation is 2m 5.1.7.5 Permissible strength of wood
According to the provisions of Table 2 of the recommended service life of wood materials. Table 2 Permissible strength of wood
Tensile strength
(of which the tensile strength
14.9:~43)
This standard is the general size calculated based on the allowable length of the component in Table 2. For the species that are suitable for use, the use life or component size can be changed according to the ratio of the allowable strength to the calculated strength in Table 2. 5.1.6 Anti-corrosion treatment of wood
When necessary, the wood should be treated with drugs, heat treatment, etc. 5.1.2 Plywood
Gluing: The glue with the same performance as specified in T3-1-19 or the glue with the same performance as specified. 5.1.3 Steel nails
Stitching in accordance with the provisions of 3/1&9, the use of glue nails can be stopped according to the situation, E-shaped parts 3
GB/T12454-2002
5.1.4 Copper belt
The quality of steel belt should meet the requirements of GB/T4175. 5.2 Space
To prevent the contents from touching the inner core of the wooden box and causing damage, fill the space between them with dry materials or leave appropriate gaps. 5.3 Inner dimensions
The dimensions of ordinary wooden boxes are expressed in inner dimensions or outer dimensions. The inner dimensions are determined as follows, and the outer dimensions can be calculated based on the inner dimensions and structure of the wooden box.
Inner length: the distance between the inner surfaces of the two end faces: Inner width: the height between the two sides:
Inner quotient: the distance between the inner surfaces of the top cover and the bottom surface. 6 Structure and dimensions
6 Dimensions of various components of type A boxes and type C boxes
The dimensions of various components of type A plastic boxes shall be in accordance with the specifications in Table 3. Table 31 Dimensions of components of type C and type C boxes
Inner material mass, k
46r-:00
1c3--15
153--20r
For taste, national
thickness: -m
Thickness/mm
45×:15
60 X15
rax tit
Note 1: The numbers in brackets are the degree of rubber tension, Note: For installation reference:, the surface can still be too thick. 6.2 Dimensions of structural components 6.2.1 The plate thickness of Type B box is measured by weight, while the plate thickness of Type H box can be determined by subtracting the weight by the method of 6.2.1.1 from 6.2.1.2, with a limit of Normal area/mm. E.2.11 According to the provisions of Table 1, the original material required for Type A box can be used and its plate ratio can be increased accordingly. Table 4 Box plate thickness
Type A end strength/such as:
Limited and total no ratio
Box plate thickness/mm
75×15
75×18
90×21
90×34
Thickness/
Table 4 (line)
Total ratio of the case chapter "Buy"
GB/T 12464-20C2 bZxz.net
Type B fall or sequence/: 0: mouth
6.2.1.2 If the same board sequence as that of type A is used, the spacing between the glued boards should be shortened by 7% of the ratio of the empty board to the total board (see Table 5).
Glued board
6.2.2 Length of type B glued board
Length direction (5)
Length direction ()
Median width ()
H-type glued board thickness is the same as that of type A, but when the thickness of the box board of type B is slower than the staggered board length of type A, the material of the same thickness of the first board of type B box should be used as the box board. 6.3 Spacing between box boards
The maximum distance between glued board and adjacent box board shall be in accordance with the provisions of 5. 6.4 Reinforcement number of this box. 4.1 Reinforced joints. When the interval between the joints exceeds the requirements of the table, the joints should be strengthened. The dimensions of the reinforced joints are the same as those of other boxes: For secondary wooden boxes, if the thickness of the upper core is not more than mm, steel belts can be used instead of the surrounding sections. The total number and position of the box and the total number of sections are determined by the box and the outermost section of the box. The distance between the box and the bottom of the box should not be less than 130mm. The bottom of the box can be appropriately thickened according to the needs. The installation position of the box is strengthened by the installation position of the box. CB/I124642002 6.4.2 Steel belt 6.4.2.1 When the box is not fixed, suitable steel can be used. The original standard of the industry is 0. For the second-level box steel belt with a thickness of 5 or less, the box can be installed within one-sixth of the length of the car, but it should not exceed 153 6.4.2.2 When the box is used, the space between the box and the box is not fixed, but when the distance between the box and the box exceeds the limit value specified in Table 5, the installation is not required. 6.4.2.3 The steel belt is semi-fixedly tied to the small block, and the strapping machine is used to tighten it. The two ends of the steel belt are overlapped and nailed on the car box. The size of the belt is in accordance with Table 6. 4 Packing materials/kk
50-2:0
6.4.3 Packing corners
The side and bottom of the box and the top of the box should be in accordance with the requirements of Table 7. The internal packaging of Table 7
:0-~2cg
6.4.4 Other ways of adding week
The quality of the product/m:
3. 5--1.6
Panel board user renewal order
Road piece quality is two-thirds
When the quality of the forbidden material is light, the volume of the front H wood glue is small, and the plastic can also be used to wrap the section. 7 Component processing requirements
7.1 Bottle splicing
Billion fast length
Difference sales must be 1,1 and
7.1.1 Box short station narrow width: sensitive box small 0mm, secondary box not less than 31= and the width of each middle m! ! According to the decision. According to the board, the thickness of the file should be appropriately matched: 7.12 The side lines of the splicing model should be parallel to each other, the folding angle should be negative, and the end ton material should not be determined to be "2mm, the single version is related to the part that is not dead, the rat, the new shape of the small surface is not less than ten of the world's living flowers. 7.13 The length of the box board is 1Uu0 mrr or less, the whole is not more than 1mm: not more than 1ccom.
72 nailing
7.2.1 The space between the boxes should be as long as possible. 7.2.2 The box rails should be parallel to each other, straight or diagonal to each other, the side plate pen rail length should not exceed the inner size, and the lower plate and half thickness should be added. 7.2.3 The length of the nail is 5mm~mm thick. The nail tip plate should be double and non-half-cross. The upper and lower parts of the nails have positions, and the end surface should not be larger than m. The city ratio is light:? 565
National nailing method
CB/T12464—2002
7.2.4 The number of nails is calculated by the width of the box surface, an average of 75mm: one, a single board greater than 90mm is not less than 2, and the upper and lower ends of the box surface are 2 virtual nails above the center of the box surface. 7.3 Wooden box assembly
7.3.1 Number of staples or: when the width of the box is increased, the flatness is 50mm" (including the book) and the remainder is greater than 30tm nails (the width is less than 150mm, at least 4>. At least 4 staples are used for corner wrapping. 7.3.2 The drop of the staples is calculated according to the doctor's multiple of the glue board's thickness. 7.3.3 The inner dimension limit deviation after the box is completed is +5mm in length, ±3mm in width, and ±2mm in quotient. The assembly method of this box is shown in Figure 3
8 Wooden pick assembly method
8 Test and inspection
8.1 Test method
8. 1. 1 Joint test
According to the ruling of GB/T4551.5.
GB/T12464-2002
8.1. 2 Stacking test
According to the provisions of GB/T4857.3
8.1.3: Moisture content test
According to the force method specified in B/T1931.
3. 2 Inspection
The embedding strength and static load of ordinary wood should be inspected, and its structure, size and materials should comply with the provisions of Chapter 5 to Chapter 7 of this standard.3. The length of the nails used is 5mm~mm thick. The nail tip plate should be double and non-half-cross. The upper and lower parts of the nails should have a position, and the end surface should not be larger than 1mm. The market ratio is: ?. 565
National nailing method
CB/T12464-2002
7.2.4 The number of nails used is calculated according to the width of the box surface. The average is 75mm: one, and the single board is greater than 90mm. There are no less than 2 nails. There are 2 virtual nails on the upper and lower ends of the box surface 2 center am. 7.3 Wooden box assembly
7.3.1 Number of staples or: when the width of the box is increased, the flatness is 50mm" (including the book) and the remainder is greater than 30tm nails (the width is less than 150mm, at least 4>. At least 4 staples are used for corner wrapping. 7.3.2 The drop of the staples is calculated according to the doctor's multiple of the glue board's thickness. 7.3.3 The inner dimension limit deviation after the box is completed is +5mm in length, ±3mm in width, and ±2mm in quotient. The assembly method of this box is shown in Figure 3
8 Wooden pick assembly method
8 Test and inspection
8.1 Test method
8. 1. 1 Joint test
According to the ruling of GB/T4551.5.
GB/T12464-2002
8.1. 2 Stacking test
According to the provisions of GB/T4857.3
8.1.3: Moisture content test
According to the force method specified in B/T1931.
3. 2 Inspection
The embedding strength and static load of ordinary wood should be inspected, and its structure, size and materials should comply with the provisions of Chapter 5 to Chapter 7 of this standard.3. The length of the nails used is 5mm~mm thick. The nail tip plate should be double and non-half-cross. The upper and lower parts of the nails should have a position, and the end surface should not be larger than 1mm. The market ratio is: ?. 565
National nailing method
CB/T12464-2002
7.2.4 The number of nails used is calculated according to the width of the box surface. The average is 75mm: one, and the single board is greater than 90mm. There are no less than 2 nails. There are 2 virtual nails on the upper and lower ends of the box surface 2 center am. 7.3 Wooden box assembly
7.3.1 Number of staples or: when the width of the box is increased, the flatness is 50mm" (including the book) and the remainder is greater than 30tm nails (the width is less than 150mm, at least 4>. At least 4 staples are used for corner wrapping. 7.3.2 The drop of the staples is calculated according to the doctor's multiple of the glue board's thickness. 7.3.3 The inner dimension limit deviation after the box is completed is +5mm in length, ±3mm in width, and ±2mm in quotient. The assembly method of this box is shown in Figure 3
8 Wooden pick assembly method
8 Test and inspection
8.1 Test method
8. 1. 1 Joint test
According to the ruling of GB/T4551.5.
GB/T12464-2002
8.1. 2 Stacking test
According to the provisions of GB/T4857.3
8.1.3: Moisture content test
According to the force method specified in B/T1931.
3. 2 Inspection
The embedding strength and static load of ordinary wood should be inspected, and its structure, size and materials should comply with the provisions of Chapter 5 to Chapter 7 of this standard.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.