title>JB/T 6036-1992 Crawler bulldozer water tightness test method - JB/T 6036-1992 - Chinese standardNet - bzxz.net
Home > JB > JB/T 6036-1992 Crawler bulldozer water tightness test method
JB/T 6036-1992 Crawler bulldozer water tightness test method

Basic Information

Standard ID: JB/T 6036-1992

Standard Name: Crawler bulldozer water tightness test method

Chinese Name: 履带式推土机 水密性试验方法

Standard category:Machinery Industry Standard (JB)

state:Abolished

Date of Release1992-05-28

Date of Implementation:1993-01-01

Date of Expiration:2008-01-01

standard classification number

Standard Classification Number:Engineering Construction>>Construction Machinery and Equipment>>P97 Construction Machinery for Building Engineering

associated standards

alternative situation:Replaced by JB/T 6036-2007

Publication information

other information

Focal point unit:Tianjin Engineering Machinery Research Institute

Introduction to standards:

This standard specifies the items, contents, methods and test result record format of crawler bulldozer watertightness test. JB/T 6036-1992 Crawler bulldozer watertightness test method JB/T6036-1992 Standard download decompression password: www.bzxz.net

Some standard content:

Mechanical Industry Standard of the People's Republic of China
JB/T6036-92
Crawler Bulldozer
Watertightness Test Method
Published on 1992-05-28
Implementation by the Ministry of Machinery and Electronics Industry of the People's Republic of China on 1993-01-01
Mechanical Industry Standard of the People's Republic of China
Crawler Bulldozer
Watertightness Test Method
1 Subject Content and Scope of Application
JB/T6036-92
This standard specifies the items, contents, methods and test result record form of the waterproof sealing performance test of crawler bulldozers. This standard is applicable to the watertightness test of industrial crawler bulldozers above 74kW, and also to the watertightness test of crawler loaders and crawler tractors of the same level.
Test items
Water (or rain) test;
Flushing test;
Small water test.
Inspection contents
Engine oil bottom filling;
Main clutch or hydraulic converter housing;
Gearbox;
Rear axle box;
Steering clutch;
Final drive box;
Fuel tank;
Hydraulic oil tank;
Cab;
Instrument panel.
Test method
Before the test, all parts should be inspected according to the inspection contents specified in Chapter 3 to confirm that there is no moisture inside. For parts filled with oil, confirm that there is no colorless turbid liquid inside.
4.1 Water spray (or rain spray) test
The tested soil spreading machine prototype is divided into one test block per square meter in the horizontal direction. The sprinkler uses 300~350kg/h of water to spray each block vertically downward for 3 hours, then wipe the surface and check whether there is water in each part. 4.2 Flushing test
After flushing the push-up machine for more than 1 hour, check whether the parts specified in Chapter 3 are immersed in water. 4.3 Water test
When the engine is adjusted to 1/2 rated speed, place the bulldozer under test in water of the allowable depth (limited to not flooding the refueling port) for 1 hour, then wipe the surface dry, check whether the parts specified in Chapter 3 are immersed in water, and check whether the water from the fan splashes the breathable cover of the hydraulic oil tank or the driver.
Approved by the Ministry of Machinery and Electronics Industry on May 28, 1992 and implemented on January 1, 1993
Test result recordbzxz.net
JB/T6036-92
The water tightness test result record of the bulldozer should be in the following table format. Any adverse conditions encountered during the test should be recorded in detail in the remarks. Crawler bulldozer water tightness test result record sheet Prototype model:
Test location:
Test unit:
Inspection content
Engine oil pan
Main clutch (or shortener)
Steering clutch
Final transmission box
Additional instructions:
Factory number:
Air temperature:
Tester:
Whether there is water
Water (or rain) test
Flushing test
This standard was proposed by Tianjin Engineering Machinery Research Institute of Shandong Machinery and Electronics Industry and belongs to Hongkou. This standard was drafted by Tianjin Engineering Machinery Research Institute of Shandong Machinery and Electronics Industry. The main drafter of this standard is Li Mingxiang.
Test date:
Water test
People's Republic of China
Mechanical industry standard
Crawler bulldozer
Watertightness test method
JB/T6036-92
Published and distributed by the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry Printed by the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry (PO Box 8144, Beijing 100081)
Copyright reserved
No reproduction
Format 880×1230
6 sheets 3/8 Number of words 4,000
First edition in October 1992 First printing in October 1992 Number of copies 00,001-500 Price 1.20 yuan
No. 0970
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.