JB/T 7497.1-1999 This standard is a revision of ZB J65 012-89 "Precision of Woodworking Planer Sharpeners". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies the requirements and inspection methods for the geometric accuracy and working accuracy of woodworking planer sharpeners. This standard is applicable to woodworking planer sharpeners with a maximum grinding length of less than or equal to 1250mm. This standard was first issued in 1989. JB/T 7497.1-1999 Precision of Woodworking Planer Sharpeners JB/T7497.1-1999 Standard download decompression password: www.bzxz.net

ICS79.120.10
Machinery Industry Standard of the People's Republic of China
JB/T7497.1～7497.2—1999
Woodworking Planer Sharpener
Published on 1999-05-14
Published by the State Bureau of Machinery Industry
Implemented on 2000-01-01
JB/T7497.1-1999
This standard is a revision of ZBJ6501289 "Precision of Planer Sharpeners". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged.
This standard replaces ZBJ65012—89 from the date of implementation. This standard was proposed by the National Technical Committee for Standardization of Woodworking Machine Tools and Tools. This standard is under the jurisdiction of Fuzhou Woodworking Machine Tool Research Institute. The responsible drafting unit of this standard: Shanghai Woodworking Machinery Factory. The main drafters of this standard are Lin Chongguang, Han Wenyuan and Zheng Zongjian. This standard was first issued in March 1989.
Mechanical Industry Standard of the People's Republic of China
Precision of Woodworking Planer Sharpeners
This standard specifies the requirements and inspection methods for the geometric accuracy and working accuracy of woodworking planer sharpeners. This standard is applicable to woodworking planer sharpeners with a maximum grinding length less than or equal to 1250mm. Cited Standards
JB/T7497.11999
ZBJ65012—89
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T 81701987
JB/T3377—1992
JB/T4171—1999
3 General requirements
Rules for rounding off values
Straight-edged planers for woodworking machines
General rules for precision inspection of woodworking machines
3.1 When using this standard, JB/T4171 should be referred to. 3.2 Before inspecting the machine tool, the installation level of the machine tool should be adjusted in accordance with 3.1 of JB/T4171-1999. The readings of the level in the longitudinal and transverse directions should not exceed 0.10/1000.
3.3 The order of precision inspection items listed in this standard does not represent the actual inspection order. In order to facilitate the installation and disassembly of inspection tools and inspection, inspections can be carried out in any order.
3.4 ​​When the measured length is different from the length specified in this standard, the tolerance shall be converted according to the measurable length in accordance with 2.2.1.1 of JB/T4171-1999, with the minimum conversion value of 0.01mm. The rounding of the numbers in the conversion shall comply with the provisions of GB/T8170. 4 Geometric accuracy inspection
Geometric accuracy inspection is shown in Table 1.
National Machinery Industry Bureau approved inspection items on May 14, 1999
Straight lines of bed guide in the heavy
straight plane
Level
Inspection method reference
JB/T 4171—1999
Related provisions
4.2.1.2.3.1
2000-01-01 implementation
JB/T7497.1—1999
Table 1 (continued)
Inspection items
Parallelism of the bed rails in the vertical plane
of the worktable surface
|Flatness
a. Longitudinal straightness
b. Horizontal straightness
c. Diagonal direction
Straightness
Grinding head spindle flange
Radial runout of the disc centering journal
Grinding head spindle flange
Spiral surface of the disc bearing surface
Circular runout
Grinding head spindle axis
Towards the inspection
The longitudinal movement of the dense head
to the
single-line degreebZxz.net
0.07/1000
Level
Indicator
Indicator
Indicator
Indicator
Inspection method refers to
Related provisions of
JB/T41711999

4.4.1.2.3.1
Measure at least the center
and one or two positions at both ends
4.3.2.2.1
Grinding head spindle has
elastic structure
This item is not subject to assessment
4.4.2.2.2.2.1
Working accuracy inspection
See Table 2 for working accuracy inspection.
JB/T7497.1—1999
Table 1 (end)
Inspection items
Parallelism of the longitudinal movement of the worktable to the worktable surface
Cutting conditions
The test piece should meet the requirements of JB/T3377
, the specification is 640x
40×4 woodworking machine straight blade
|Inspection items
Blade edge
Straightness
Grinding surface
Roughness
Indicator
Roughness
Inspection method shall refer to
Related provisions of JB/T4171—1999
4.4.2.2.2.1
Inspection method shall refer to
Related provisions of JB/T4171—1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.