title>Polyethylene extrusion foaming packaging materials - BB/T 0066-2017 - Chinese standardNet - bzxz.net
Home > BB > Polyethylene extrusion foaming packaging materials
Polyethylene extrusion foaming packaging materials

Basic Information

Standard ID: BB/T 0066-2017

Standard Name:Polyethylene extrusion foaming packaging materials

Chinese Name: 聚乙烯挤出发泡包装材料

Standard category:Packaging Industry Standard (BB)

state:in force

Date of Release2017-04-12

Date of Implementation:2017-10-01

standard classification number

Standard ICS number:Packaging and transportation of goods >> 55.040 Packaging materials and auxiliary materials

Standard Classification Number:General>>Marking, packaging, transportation, storage>>A82 Packaging materials and containers

associated standards

Publication information

publishing house:China Planning Press

Publication date:2018-01-01

other information

drafter:Liu Hui, Wang Zhenhua, Zou Hong, Cao Zhihuai, Zhang Wenbin, Sun Heyong, Niu Shumei, Cui Jie, Ye Baizhang

Drafting unit:China Packaging Research and Testing Center, Zhejiang Jiuding Plastic Technology Co., Ltd., Saiwen (Tianjin) Industrial Co., Ltd., Chongqing Bishan County Jiecheng Plastic Co., Ltd., Dongguan Heyong Packaging Co., Ltd., China Packaging Federation Ele

Focal point unit:National Packaging Standardization Technical Committee (SAC/TC 49)

Proposing unit:China Packaging Federation

Publishing department:Ministry of Industry and Information Technology of the People's Republic of China

competent authority:National Packaging Standardization Technical Committee (SAC/TC 49)

Introduction to standards:

BB/T 0066-2017 Polyethylene extrusion foaming packaging materials, the format of this standard is pdf, the size is 2.3M, free download. Polyethylene extrusion foaming packaging materials www.bzxz.net updates various standards every day, all of which are free for everyone to download. If you need any standards, just leave a message to the editor. I will reply to you in time.
This standard specifies the terminology, classification, requirements, test methods, inspection rules, marking, packaging, transportation and storage of polyethylene extrusion foaming packaging materials. This standard applies to polyethylene foaming packaging materials made of polyethylene resin as the main raw material, adding physical foaming agents and other additives, and extruded.


Some standard content:

ICS55.040
Packaging Industry Standard of the People's Republic of China
BB/T0066—2017
Polyethylene extrusion foaming packaging materials
Polyethylene extrusion foaming packaging materialsPublished on April 21, 2017
Published by the Ministry of Industry and Information Technology of the People's Republic of China
Implemented on October 1, 2017
BB/T0066—2017
This standard was drafted in accordance with the rules given in GB/T1.1-2009 "Guidelines for Standardization Work Part 1: Structure and Preparation of Standards". Some contents of this document may still involve patents. The issuing agency of this document does not assume the responsibility for identifying these patents. This standard is proposed by the China Packaging Federation. This standard is under the jurisdiction of the National Technical Committee for Packaging Standardization (SAC/TC49). The drafting units of this standard are: China Packaging Research and Testing Center, Zhejiang Jiuding Plastic Technology Co., Ltd., Saiwen (Tianjin) Industrial Co., Ltd., Chongqing Bishan County Jiecheng Plastic Co., Ltd., Dongguan Heyong Packaging Co., Ltd., and China Packaging Federation Electronic Industry Packaging Technical Committee.
The main drafters of this standard are: Liu Hui, Wang Zhenhua, Zou Hong, Cao Zhihuai, Zhang Wenbin, Sun Heyong, Niu Shumei, Cui Jie, and Ye Baizhang. This standard is published for the first time.
1 Scope
Polyethylene extrusion foaming packaging materials
BB/T0066-—2017
This standard specifies the terminology, classification, requirements, test methods, inspection rules, marking, packaging, transportation and storage of polyethylene extrusion foaming packaging materials (hereinafter referred to as products).
This standard applies to polyethylene foaming packaging materials made of polyethylene resin as the main raw material, adding physical foaming agents and other additives, and extruded.
2 Normative references
The following documents are indispensable for the application of this document. For any dated reference, only the dated version applies to this document. For any undated reference, the latest version (including all amendments) applies to this document. GB/T191 Pictorial marking for packaging, storage and transportation
GB/T1410
Test method for volume resistivity and surface resistivity of solid insulating materials GB/T2406.2—2009 Determination of burning behavior of plastics by oxygen index method Part 2: Sampling inspection procedure for room temperature tests by counting Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL) GB/T2828.1
GB/T6342
GB/T6343
GB/T6344
Linear dimensions of foam plastics and rubber Determination of apparent density of foam plastics and rubber Determination of tensile strength and elongation at break of flexible foam polymeric materials GB/T6669-2008 Determination of compression set of flexible foam polymeric materials GB/T8167
GB/T10808
GB/T14745
3 Terms and definitions
Test method for dynamic compression of cushioning materials for packaging Determination of tear strength of porous elastic materials of polymers Packaging
Grade impact materials
Test method for variable properties
The following terms and definitions apply to this document. 3.1
Apparent density
apparentdensity
The mass of polyethylene extruded foam packaging material per unit volume. 4 Classification
4.1 According to the apparent density of the product, it is divided into: I type, II type, III type and V type, see Table 11
BB/T0066-—2017
Apparent density range and classification
According to the functional characteristics of the product, it is divided into: anti-static type, flame retardant type, ordinary type. Requirements
Apparent density
≥20.0~<30.0
≥30.0~<60.0
The product should not have cracks, stiff blocks and impurities, no pollution, no odor; no swelling and shrinkage; uniform color, no obvious color difference, uniform pore size; when bonding multiple layers, it should be bonded evenly and without cracking. 5.2
Average thickness deviation
The average thickness deviation should meet the requirements of Table 2.
Average thickness deviation
≥2.0~5.0
>5.0~15.0
≥15.0~30.0
≥30.0~60.0
Apparent density deviation
Apparent density deviation shall comply with the provisions of Table 3.
Apparent density deviation
Average deviation
Apparent density deviation
Unit: mmwwW.bzxz.Net
5.4 Tensile properties, tear properties and compression properties BB/T0066—2017
5.4.1 Products with a thickness of less than 25 mm are tested for tensile strength; products with a thickness of 25 mm and above are tested for tear strength, compression strength and compression permanent deformation.
5.4.2 The requirements for tensile, tear and compression properties shall comply with the provisions of Table 4. Table 4 Tensile properties, tear properties and compression properties Tensile strength
Surface resistivity
Tear strength
The surface resistivity of antistatic products is 10\Q~10\a. Oxygen index
The oxygen index of flame retardant products should be ≥26%.
5.7 End-change characteristics and dynamic compression properties
Tests should be carried out according to the product use and the requirements of the purchaser. 6 Test methods
6.1 Standard environment for sample conditioning and testing
Compression strength
Compression 25%
Compression 50%
≥150
Compression permanent deformation
Compression 50%
Put the sample in an environment with a temperature of 23℃±2℃ and a relative humidity of 50%±5%, and the state conditioning time shall not be less than 24h. 6.2 Appearance
Visual inspection under natural light.
6.3 Average thickness deviation
6.3.1 For Type I products, the test shall be carried out in accordance with the provisions of GB/T8167. A rigid plate shall be placed on the upper surface of the test sample, so that the test sample is subjected to a compressive load of (0.20±0.02) kPa. After 30 seconds, the test shall be carried out under load with a gauge with a minimum graduation value of no more than 0.05 mm and an accuracy of 0.1 mm.
6.3.2 For Type II, III and IV products, the test shall be carried out in accordance with the provisions of GB/T6342. When the thickness is less than 10 mm, a gauge with an accuracy of no less than 0.05 mm may be used. When the thickness is between 10 mm and 100 mm, a gauge with an accuracy of no less than 0.1 mm may be used. When the thickness is greater than 100 mm, a gauge with an accuracy of 0.5 mm may be used.
6.3.3 Calculation
Take 1 sample and measure the thickness at 5 different points. The measuring points are evenly distributed. Each point is measured 3 times. The median of the 3 readings is taken. The average value is calculated using the 3
BB/T0066—2017
5 medians.
6.4 Apparent density deviation
According to the provisions of GB/T6343. The volume of a single sample is at least 100cm: the number of samples is 5. The apparent density deviation value is the apparent density measured value minus the nominal value, and the average value of the 5 samples is calculated. 6.5 Tensile, tear and compression properties
6.5.1 Tensile strength
According to the provisions of GB/T6344. The sample thickness is 10mm (for products with a thickness of less than 10mm, the actual thickness is used for testing; for products with a thickness of more than 10mm, the thickness is cut to 10mm for testing). The number of samples is 5 in each direction. The moving speed of the clamp of the tensile testing machine is (500 ± 50) mm/min. Calculate the average value of 5 specimens. 6.5.2 Tear strength
Perform in accordance with the provisions of GB/T10808. Specimen size: length (125 ± 25) mm, width (25 ± 1) mm, thickness (25 ± 1) mm. The number of specimens is 3 in each direction. The moving speed of the clamp is (50 ± 5) mm/min. Calculate the average value of 3 specimens. 6.5.3 Compression permanent deformation
Perform in accordance with the provisions of GB/T6669-2008 Method C. Specimen size: 50 mm × 50 mm × 25 mm. Specimen number 5. Compress the specimen by 50% of its thickness at the same temperature as the state conditioning; compression time (24 ± 0.2) h. Calculate the average value of 5 specimens. 6.5.4 Compression strength
6.5.4.1 Sample size: 50mm×50mm×25mm, or 100mm×100mm×25mm. 6.5.4.2 Number of samples: 5.
6.5.4.3 Pre-compress 190Pa±50Pa, measure and record thickness, compression speed 12.5mm/min, compress 25% and 50% respectively, record the force value when compressed 25% and 50%.
6.5.4.4 Calculation
The calculation of compression strength is shown in formula (1):
CD=F/AX10%
Wherein:
CD compression strength, unit kilopascal (kPa);
F force value when the sample is compressed 25% and 50%, unit Newton (N); A-compressed area of ​​the sample, unit square millimeter (mm). Calculate the average value of 5 samples.
6.6 Scorpion deformation performance
(1)
Perform in accordance with GB/T14745. Sample size: minimum size not less than 50mm×50mm×25mm, the number of samples not less than 5; test time is determined by negotiation as needed.
6.7 Dynamic compression performance
Perform in accordance with GB/T8167. The test sample is a regular rectangular shape; the area of ​​the upper and lower bases is at least 100mm×100mm, and the thickness is not less than 25mm. The number of samples in a group is not less than 5. 6.8 Surface resistivity
It is carried out in accordance with the provisions of GB/T1410. The shape of the sample is not limited. 6.9 Oxygen index
BB/T0066-2017
It is carried out in accordance with the provisions of GB/T2406.2-2009 Method A. Sample size: length 80mm, width (10±0.5)mm, thickness (10±0.5)mm, and the number of samples is 15. 7 Inspection rules
7.1 The inspection of products
is divided into factory inspection and type inspection.
7.2 Factory inspection
The factory inspection items are appearance, average thickness deviation, apparent density deviation and tensile strength. 7.3 Type inspection
Type inspection is for all items specified in this standard. Type inspection shall be carried out in any of the following situations: a)
At least once in normal continuous production for one year; when the production equipment, material and process conditions have changed significantly, which may affect the product performance; b)
When the product has been suspended for more than 6 months and resumed production; c)
When the factory inspection results are significantly different from the last type inspection: e)
When the quality supervision department makes a request. 7.4 Batch
Products produced with the same raw materials, the same formula and the same process conditions are grouped as one batch according to the output per shift. The maximum batch shall not exceed 1500 pieces. 7.5 Sampling
7.5.1 Appearance and thickness According to the secondary normal sampling plan specified in GB/T2828.1, the general inspection level IⅡ is adopted, and the acceptance quality limit (AQL) is 6.5.
7.5.2 Random sampling method is adopted for apparent density and tensile, tearing and compression properties. Three samples are randomly selected from each batch for inspection. 7.6 Judgment rules
If there are unqualified items in the average deviation of appearance and thickness, the piece is judged to be unqualified. If one of the test results of apparent density and tensile, tearing and compression properties is unqualified, double the number of samples should be drawn from the original batch to re-inspect the unqualified items. If all the re-inspection results are qualified, the batch of products is judged to be qualified; otherwise, the batch is unqualified, the unqualified products should be eliminated, and the unqualified batch of products should be resubmitted for inspection. 8 Marking, packaging, transportation and storage
8.1 Marking
The packaging, storage and transportation marking shall be carried out in accordance with GB/T191. Each package is accompanied by a certificate of conformity, which should indicate the name of the manufactured product, specifications, factory name, address, production date or production batch number and inspector code, etc. 5
BB/T0066—2017
8.2 Packaging
Pack a certain number of products into pieces and use outer packaging with rainproof or moisture-proof functions. 8.3 Transportation
Rain, snow and exposure to the sun should be avoided during transportation. Fireworks are strictly prohibited. Tools that damage product quality should not be used. It is prohibited to throw and drop packages during loading and unloading. 8.4 Storage
It should be stored in a clean, ventilated and dry warehouse. It is strictly prohibited to be exposed to the sun and rain. Keep away from fire sources and corrosive and toxic substances. The storage period is 12 months from the date of production; re-inspection is required after the expiration.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.