title>JB/T 5812-1991 Type and size of winding wire enameling equipment - JB/T 5812-1991 - Chinese standardNet - bzxz.net
Home > JB > JB/T 5812-1991 Type and size of winding wire enameling equipment
JB/T 5812-1991 Type and size of winding wire enameling equipment

Basic Information

Standard ID: JB/T 5812-1991

Standard Name: Type and size of winding wire enameling equipment

Chinese Name: 绕组线漆包设备 型式尺寸

Standard category:Machinery Industry Standard (JB)

state:Abolished

Date of Release1991-10-17

Date of Implementation:1992-10-01

Date of Expiration:2008-07-01

standard classification number

Standard Classification Number:Electrical>>Electrical Production Equipment>>K91 Electrical Material Production Equipment

associated standards

alternative situation:Replaced by JB/T 5812-2008

Publication information

other information

Focal point unit:Shanghai Cable Research Institute

Publishing department:Shanghai Cable Research Institute

Introduction to standards:

This standard specifies the types and dimensions of the electric heating baking equipment for winding wire enamel insulation. This standard applies to the design, manufacture, acceptance, identification and quality assessment of the enameling equipment for baking single or composite enamel film on round or rectangular conductors. JB/T 5812-1991 Types and dimensions of winding wire enameling equipment JB/T5812-1991 Standard download decompression password: www.bzxz.net

Some standard content:

1 Subject content and scope of application
Machinery Industry Standard of the People's Republic of China
Winding wire enameling equipment
Type and size
This standard specifies the type and size of the winding wire enamel insulation electric heating baking equipment. JB/T5812-91
This standard is applicable to the design, manufacture, acceptance, identification and quality assessment of enameling equipment for baking single or composite enamel films on round or rectangular conductors.
2 Reference standards
GB2900
GB4004
JB2863
Electrical terminology
Priority numbers and priority number systems
Wire drums for wire and cable machines
Model compilation method for wire and cable special equipment JB/T5814.6 Basic parameters of wire and cable special equipment Part 6 Enameling equipment 3 Terms
3.1 The definition of terms in this standard adopts the interpretation of GB2900. 3.2 Multi-groove guide wheel Multigroove idler sheave A guide wheel with multiple wire grooves on the circumference of a wheel body. 3.3 Single-groove guide wheel Singlegroove idler sheave A guide wheel with only one wire groove on the circumference of a wheel body. 3.4 Gather up pooling
A method of collecting and arranging wires in which multiple enameled wires are concentratedly pulled by a traction wheel and then wound on the drum separately. The device is an independent component consisting of multi-head centralized traction, multi-head centralized wiring or single-head wiring, and single-head winding, called a centralized wire-taking device. The type of centralized wire-taking device can be a traction wheel or a group of traction wheels. 3.5 Single-head spooling Each enameled wire is pulled individually by a traction wheel and then wound on a reel. The device is a unit consisting of single-head traction, single-head wiring and single-head winding, called a single-head wire-taking device. The enameling equipment can be equipped with the number of single-head wire-taking devices according to the number of heads, or the specifications of the single-head wire-taking device can be adjusted according to the wire diameter and the reel capacity.
3.6 Off-gas cleaning
The treatment of eliminating harmful gases in the flue gas generated in the furnace during the baking process. Catalytic combustion is a way of flue gas purification, which ignites the flue gas through the action of a catalyst for purification. 3.7 Hot air circulation Hot air circulation is a process method that uses forced ventilation to return the purified hot air to the furnace to bake the insulating paint film. 4 Naming and code
4.1 Code
Approved by the Ministry of Machinery and Electronics Industry on October 17, 1991 [implemented on October 1, 1992
4.1.1 Category code
Enameling equipment category
4.1.2 Series code
Electrothermal baking series H
4.1.3 Type code
4.2 Representation method
JB/15812-91
4.2.1 The equipment is composed of a name code and a specification code. The product marking is represented as follows: Standard number
Specification code
Type code
Series code
4.2.2 Example
Vertical enameling machine, wire diameter serial number 1, one baking oven, number of heads 8, number of paint passes 10. Expressed as: QHL1/1-8/10JB/T5812-91b. Vertical enameling machine, wire diameter serial number 1, two ovens, head number 8, paint number 10. Expressed as: QHL1/28/10JB/T5812-915General provisions
5.1 The determination of the dimensions of the enameling machine and its main parts shall be based on scientific basis, implement the provisions of GB321, and take the values ​​according to the priority number and priority number system as much as possible.
5.2 The key elements in the use of the product shall clearly specify the dimensions. The following elements are the key elements in the use of the enameling machine:a.
Interface dimensions inside and outside the product;
Interchangeable dimensions;
Dimensions indicating the series specifications of the enameling machine;
d. The dimensions of the anchor screw holes for installation and related process dimensions. 5.3 The main dimensions of the wire-paying device, wire-pulling device, annealing device, paint supply, painting device, oven device, flue gas treatment device, cooling device, drying device, wire-taking device and electrical control part of the enameling machine shall be interconnected to ensure the coordinated functions of each part. 5.4 The wire reel dimensions of the wire-taking device shall comply with the provisions of GB4006. 6 Wire-paying device
6.1 Type
Type as shown in Figure 1
6.2 Dimensions
6.2.1 The wire reel dimensions shall comply with the provisions of GB4004. 2
6.2.2 Other dimensions to be determined.
7 Oven
7.1 Type
Electric heating type as shown in Figure 2
. Baking furnace, horizontalbZxz.net
7.2 Dimensions
a Rotating pay-off
JB/T5812-91
b Baking furnace, vertical
7.2.1 The cross-sectional dimensions of the furnace body shall comply with the provisions of Table 1-1. A and B are not specified. 7.2.2 The dimensions of the furnace frame shall comply with the provisions of Table 1-2. Table 1-1
Wire diameter code
500, 630
710, 800
900, 1000
1200, 1300
Not specified
Over-end pay-off
c Baking furnace, cross-sectional
710, 1000
1200,1400
800,1000
1300,1500
630,800
1000,1300
Wire diameter code
Wire-taking device
500,630
800,900
1200,1300
500,630
800,900
1200,1300
710,900
1000,1200
Centralized type;
Single-head type.
The diameter of the traction wheel shall comply with the provisions of Table 2.
Other sizes to be determined
Centralized type
Single-head type
9.1 Type
Type as shown in Figure 3
Guide roller type:
Single-groove type;
c. Multi-groove type.
9.2 Size
JB/T5812-91
Continued Table 1-1
Table 1-2
800~1000
80,100,125,160,200,250,315,400,500,630,710,800,900,100080,100,125,160,200,250,315,400,500,630,710,800,900,1000
Should conform to the requirements of Table 3.
Single groove guide wheel
Multi-groove guide wheel
Additional instructions:
a Guide type
JB/T5812-91
b Multi-groove type
e Single groove type
20,25,30,40,50,63,71,80,90,100,1
125,160,2 00
250,280,315,355,400,
,500,630,710,800,900
25,30,40,50,63,71,8
80,90,
100,125,160,200
250,280,315,355,400,500,630,710,800,900This standard is proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by Shanghai Cable Research Institute and other units. The main drafters of this standard are Jin Tiegang and Li Guoku. mm
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.