JB/T 3582-1999 Basic parameters of anvil micro-motion hydraulic die forging hammer
Basic Information
Standard ID:
JB/T 3582-1999
Standard Name: Basic parameters of anvil micro-motion hydraulic die forging hammer
Chinese Name:
砧座微动型液压模锻锤 基本参数
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-05-14
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Mechanical Manufacturing>>Chipless Processing Equipment>>25.120.10 Forging Equipment, Punching Machines, Shearing Machines
Standard Classification Number:Machinery>>General Processing Machinery and Equipment>>J62 Forging Machinery
Publication information
other information
Focal point unit:National Forging Machinery Standardization Technical Committee
Introduction to standards:
JB/T 3582-1999 JB/T 3582-1999 Basic parameters of anvil micro-motion hydraulic die forging hammer JB/T3582-1999 Standard download decompression password: www.bzxz.net
Some standard content:
ICS25.120.10
Machinery Industry Standard of the People's Republic of China
JB/T3582-1999
Anvil Micro-motion Hydraulic Die Forging Hammer
Basic ParameterswwW.bzxz.Net
Published on 1999-05-14
National Bureau of Machinery Industry
Implemented on 2000-01-01
JB/T3582—1999
This standard is a revision of JB3582—84 "Basic Parameters of Micro-motion Hydraulic Hammer with Brick Seat". The technical content of this standard is basically consistent with that of JB3582—84, and it has only been re-edited according to relevant regulations. This standard shall be implemented from January 1, 2000
This standard replaces JB3582—84 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Forging Machinery. The drafting unit of this standard: Jinan Foundry and Forging Machinery Research Institute. This standard was first issued in February 1984.
1 Scope
Machinery Industry Standard of the People's Republic of China
Brick-seated micro-motion hydraulic die forging hammer
Basic parameters
This standard specifies the basic parameters of the anvil micro-motion hydraulic die forging hammer. This standard is applicable to general hydraulic die forging hammers. 2 Basic parameters
2.1 The main parameter of the hydraulic die forging hammer is the striking energy. 2 The basic parameters of the hydraulic die forging hammer shall comply with the provisions of Table 1. 2.2
Strike energy E
Strike stroke S
Guide rail spacing B
Length of the lower plane of the hammer head L
Minimum die height H
Amount of anvil jump Si
Direct transmission
Number of strikes
Combined transmission
1 The recommended nitrogen or compressed air pressure p is 0.6-1.0MPa. 2Recommended expansion ratio AV/V=0.25-0.35.
3Recommended striking speed 1=6-8ms
Approved by the State Machinery Industry Bureau on 1999-05-1463
40~150
JB/T3582—1999
Replaced JB3582-84
Implemented on 2000-01-01
Mechanical industry standard
Anvil micro-motion hydraulic die forging hammer
Basic parameters
JB/T3582—1 999
Published by the Machinery Standardization Research Institute of the Ministry of Machinery Industry Printed by the Machinery Standardization Research Institute of the Ministry of Machinery Industry (No. 2 Shouti South Road, Beijing, Postal Code 100044)*
1/16 Printing sheet 1/4 Word count 4000
Format 880×1230
First edition in September 1999
First printing in September 1999
Print run 1-500
Price 500 yuan
99-513
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.