This standard specifies the energy efficiency grade, energy efficiency limit value, energy saving evaluation value, test method and inspection rules for self-ballasted fluorescent lamps for general lighting. This standard applies to self-ballasted fluorescent lamps with a rated voltage of 220V, a frequency of 50Hz AC power supply, a standard power of 60W or less, with screw-type lamp holders or bayonet lamps, used for general lighting in homes and similar occasions, and with integrated control start and stable ignition components. GB 19044-2003 Energy efficiency limit values ​​and energy efficiency grades for self-ballasted fluorescent lamps for general lighting GB19044-2003 Standard download decompression password: www.bzxz.net

4.3 of this standard is mandatory, and the rest of the clauses are mandatory. This standard is proposed by the National Economic and Trade Commission and the National Standardization Administration. The National Energy Basic and Management Standardization Technical Committee Reasonable Electricity Use Branch is responsible for this standard. CE19044—2003
This standard was drafted by China Standard Research Center, Beijing Electric Light Source Research Institute, National Electric Light Source Quality Inspection Center (Beijing), National Electric Light Source Quality Inspection Center (Shanghai), Nanjing East China Neutron Research Group Co., Ltd., Zhejiang Optical Group Co., Ltd., Beijing Matsushita Light Source Co., Ltd., National Environmental Committee Energy Research Institute. The main drafters of this standard are: Chen Haihong, Yue Fujin, Za Suhui, De Ning, Hua Shuming, Yu Anqi, Che Aixian, Liu Wei, Yao Nianbian, Hang Jun, 1 Scope
GH19044-2003
Energy efficiency limit values ​​and energy efficiency grades of self-ballasted fluorescent lamps for general lighting This standard specifies the energy efficiency grades, total efficiency limit values, energy saving evaluation values, test frequency method and charging rules of self-ballasted fluorescent lamps for general lighting (hereinafter referred to as self-ballasted fluorescent lamps). This standard is applicable to self-ballasted fluorescent lamps with a rated voltage of 220V, a frequency of 0Hz, a standard operating frequency of 6CW and below, using a lamp holder induction lamp, and generally used in homes and similar occasions, with integrated control and stability components. This standard does not apply to self-ballasted fluorescent lamps with shunting. 2 Normative references
The following documents are incorporated into this standard through reference. H. For dated references, all subsequent amendments (excluding errors) or revisions are not applicable to this standard. However, parties that reach an agreement based on this standard are encouraged to study whether new versions of these documents can be used. For any referenced document without a date, the latest version applies to this standard. GB/T2825 Sampling procedure and sample table for batch inspection (applicable to the following inspection of subsequent batches): (H225 Periodic inspection sampling procedure and table (applicable to the inspection of the specified batches) GB/T17263 Performance requirements for self-ballasted fluorescent lamps for general lighting 3 Terms and definitions
In addition to the definitions in GB17253, this standard also uses the following terms and definitions. 3.1
Initial luminous efficiency of self-ballasted fluorescent lamps telnuoresceutIunps is a reference for evaluating the energy efficiency level of self-ballasted fluorescent lamps - this parameter is the ratio of the initial luminous flux of the self-ballasted fluorescent lamp to the measured power, and the unit is 1m/W.
Energy efficiency limit for self-ballasted fluorescent lamps is the minimum initial luminous efficiency of self-ballasted fluorescent lamps allowed under the test conditions specified in the standard. 3. 3
Energy efficiency evaluation value of self-ballasted fluorescent lamps
The minimum initial luminous efficacy value for evaluating the energy efficiency level of ballasted fluorescent lamps. 4 Technical requirementswwW.bzxz.Net
4.1 Basic requirements
The performance of self-ballasted fluorescent lamps to which this standard applies shall comply with the requirements of G1726H. 4.2 Energy efficiency grades and luminous flux
4.2.1 Energy efficiency grades
The energy efficiency grades of self-ballasted fluorescent lamps are divided into 3 levels, of which grade 1 is the highest: the initial luminous efficacy value of each grade shall not be lower than the requirements in Table 1. CB 19044--2003
Type width:
15--34
23-~60
Table t good final flow installed light lamp magic effect etc.
Heat light effect/
Energy level (Dongshang.RR.R2)
Energy meal etc. (color full RL,R9,RN.ND!
Large color measurement and density etc./17203 in 3 color from the prohibition of the requirements, the enterprise is not the extreme marriage angle production requirements of the curve manufacturing non-standard period of the lamp, similar to the Jiaohe Xie control the promise to the standard device color to coordinate the spring standard value, and its production of good M of the range For lamps that are better than non-standard lamps, the luminous efficiency of the standard lamps shall be determined. 4.2.2 Luminous flux maintenance rate
When the luminous flux maintenance rate of each energy frequency is 20°C, the luminous flux maintenance rate shall not be less than 34.3% of the energy efficiency rating in Table 1. The luminous flux maintenance rate shall comply with the provisions of 4.2.2. The energy-saving evaluation value and luminous flux maintenance rate
of the energy efficiency rating in Table 1 shall be 2%. The luminous flux maintenance rate shall comply with the provisions of 4.2.2. 5 Test method
5.1 General requirements for the test
Carry out the test in accordance with the requirements of GE/T17253. 5.2 Light efficiency
The light intensity test method in B/263 is carried out, and the light efficiency is calculated. 5.3 Chromatic coordinates
The total price is fixed and the color test method in B3 is carried out. 5.4 Luminous flux||tt ||08/17263 Technical test and acceptance inspection rules
6.1. Acceptance inspection
The manufacturer shall limit the sales of the self-ballasted fluorescent lamps produced by the enterprise to the age limit. Products that have not passed the frequency test will not be allowed to leave the factory. The self-ballasted fluorescent lamps for acceptance inspection shall be randomly selected from the same batch of lamps produced in each shift. The acceptance test shall be carried out according to the test items, sampling methods and inspection plans specified in Table 2. 2 Acceptance test sample inspection water level test confirmation item
6.2 Routine test
According to the technical requirements
Test method
Yun added Fang Dong
Control check water "F
Condensation plant should mine the body of the enterprise's production of the town of light from the fixed image reverse column test, Ya single year model included in the full range of test lamps randomly selected. In case of any adverse circumstances, the research requirements for the test: the product trial model will be forgotten,
When the production card is more than one year to resume production:
When the design, process or material changes mountain c
d) When the quality and technical supervision department conducts routine tests, the routine test shall be carried out according to the one-axis sampling plan of GB/T2829, level 1. The test items, sampling quantity, unqualified quality level and unqualified judgment number shall be as specified in the table.
Table 3 Routine test unqualified quality level, sampling quantity and judgment of the whole group
Initial luminous efficiency
Original standard
Luminous flux rate
Technical requirements
Test method
Column size
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.