title>JB/T 9121-1999 Book binding machine - JB/T 9121-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 9121-1999 Book binding machine
JB/T 9121-1999 Book binding machine

Basic Information

Standard ID: JB/T 9121-1999

Standard Name: Book binding machine

Chinese Name: 捆书帖机

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-07-12

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:Imaging technology>>Printing technology>>37.100.10 Printing and copying equipment

Standard Classification Number:Machinery>>General Machinery and Equipment>>J87 Printing Machinery

associated standards

alternative situation:ZB J87017-1990

Publication information

other information

Focal point unit:National Printing Machinery Standardization Technical Committee

Introduction to standards:

JB/T 9121-1999 JB/T 9121-1999 Book Binding Machine JB/T9121-1999 Standard Download Decompression Password: www.bzxz.net

Some standard content:

10:4 37. 100. 14
Machinery Industry Standard of the People's Republic of China
JR/T9121-1999
Book Binding Machine
Bundlingmachine
Published on 1999-07-12
National Bureau of Machinery Industry
Implemented on 2000-01-01
JH/T9121-1999
This standard is a revision of ZBJ87017-90 Technical Conditions for Horizontal Bundling Machines. Compared with ZHJ87U17-9U, this standard is renamed as Book Binding Machines, making the standard name more standardized. This standard replaces ZBJB7017-90 from the date of implementation and is proposed and managed by the National Technical Committee for Machinery Standardization. Standard drafting unit: Yibin Dayehe Machinery Co., Ltd. The main drafters of this port are Qing Shangti and Gong Yousheng: This standard was first issued on May 27, 1990. 1 Scope
Machinery Industry Standard of the People's Republic of China
Bookbinding machine
Runding machine
JB/T9121-1999
2 x? 7.-
This standard specifies the basic parameters, technical requirements, test methods, inspection specifications, marking, packaging, storage and transportation of horizontal bookbinding machines (hereinafter referred to as running machines). This standard applies to horizontal dynamic bookbinding machines and liquid-type running machines. 2 Referenced standards
The provisions contained in the following standards shall constitute the provisions of this standard by reference in this standard. The versions shown shall be valid. All standards will be revised. The users of this standard shall explore the possibility of reverting to the latest version of the following standards GB19:1990
GB/T 788—196?
GB.T5226.1-1996bZxz.net
GB:63881986
B.79969.1—[998
B:133(16—991
QB13384—1992
GB. 14436--1993
JRT3090—
3Basic parameters
Packing and storage Small logo
Open books, magazines and prohibitions
"Industry Mechanical and electrical equipment Part 1: Chain production technical conditions Transport package list Receiving and shipping signs
1 Industry product pressure manual General provisions
General technical conditions for packaging of mechanical and electrical products
1 Industry production guarantee document General provisions
Product model compilation method of printing machinery
5.1 The size of the printing machine shall be less than the A4 (16) size in 7881987. 3.2 The model and name of the printing machine shall be in accordance with the provisions of JB3090. Technical requirements
4.1 The printing station shall be in accordance with the technical board standard 4.2 The butterfly pattern pair should be flexible and free from sticking. 4.3 Shaft temperature rise should not exceed 35°C. 4.4 The maximum limit of the inner pair of two rope plates should not exceed the nominal value. The parallelism tolerance of the two plates should not exceed 5 mm. 4.5 The movement speed of the movable rope plate should not be less than 90 mm/s. The movement should be smooth without impact or spontaneous vibration. 4.6 The pressure should not exceed 100%. 5kN or more, spring capacity is good. 4.: The end is tight, the post after holding should be flat, approved by the State Machinery Industry Bureau in 1999 and 0712. Implementation on 2000-01-01. 4.8 Electrical quality record. 4.8.1 The discharge control should be as flexible as possible. JB/T9121-[999]. 4.8.2 The insulator resistance between the machine and the power supply line is less than 1500 V50 Hz. 4.8.3. The grounding device and marking of the machine component are not more than 10.1. 4.9 Appearance quality is not visible. 4.9.1 The exposed surface and the painted surface should not be rusted, rusted or have obvious marks. 4.9.2 Exposed non-processed: surface state holes, convex fans, call drops and other defects. Attached 5 Test methods
5.1 Each product is tested for 30m idling. Monthly inspection of the plate movement, spring multi-position, seven-device control, etc., as far as possible in accordance with the provisions of 4,
5.2 The maximum distance and running error between the inner sides of the two rope plates are required to be measured. 5.2.1 The movable rope plate is withdrawn to the limit position, and the inner side of the two rope plates are measured with a steel ruler. The height is accurate to G.5mm1. 5.2.2 The inner side of the distance plate is connected to the distance between the four points outside the measuring plate. The total maximum error is the parallelism error, which should meet the provisions of 44. 5.3 The moving distance plate travel speed is measured to
: When measuring the appropriate rope movement speed, use a stopwatch to time, and use a ruler to measure the start and stop distance. Calculate the moving rope speed: 6 Use a tachometer to read the trapezoidal tripod speed, and then multiply it by the pitch, and the movable plate movement is connected. The internal calculation of force is equivalent, and the result should comply with the provisions of 4.5. 5.4 Maximum tightening force
Standard measurement force groove width red set between the lower rope plate, start the machine special elastic group compression until the motor stalls, use the expansion card to minimize the deformation of the elastic dimension, the rain variable standard card stiffness calculation mountain report maximum melon case force P: Medium:
Maximum tightening AH, N;
Number of pieces:
3——degrees, Nmm: ||t t||F,—deformation, mm
The measurement result shall meet the requirements of 46
5.5Monthly visual inspection and external quality shall meet the requirements of 4.9 gauge pp'F
5:6When the product leaves the factory, the negative test shall be carried out according to A (161, A5 (2) specified in G8819, but the far-type flight certificate shall be carried out for no less than five times of rejection, loosening, holding holes, etc., and meet the requirements of 4.7. 5.7According to GH 5226.1-1-6 Section 20 Inspection method for electrical quality inspection: should comply with 4.8 provisions. 6 Inspection rules
6 units must be inspected for quality before they are shipped out. The products must be inspected according to the specifications in 4. If there is one item that is unqualified, the product will be considered as an unqualified product: Product supply range
) Analysis:
b must be attached to the flow, fragility:
8.1. Each product shall be labeled in a conspicuous place. The label shall comply with the provisions of the regulations and include: a) manufacturer name; b) product model and name; c) main technical parameters; e) packaging and storage; e) transportation. 1.2. Product packaging and storage shall be in accordance with the provisions of GB[9] 8.1.3. Transport containers shall be selected correctly. The delivery mark shall comply with the provisions of H/T 6388. 82 Packaging
8.2.1 Before packaging, the exposed parts and plated parts shall be treated with rust prevention. 8.2.2 The packaging of products shall comply with the provisions of H/T13584. 8.3 Storage
Products should be stored in a well-ventilated place to avoid moisture. If the storage period exceeds 100%, the product shall be repackaged if any defects are found during unpacking and inspection before leaving the factory. 8.4 Transportation
When transporting products, they shall be lifted and placed gently according to the lifting marks on the outer wall of the packaging box. Do not fall or bump into the product. 5 The following documents must be provided for each product when it leaves the factory: a: Certificate
The product certificate number shall comply with the provisions of H/T 14436. ! Instruction Manual
The instruction manual shall be written in accordance with the provisions of 0B19969.1. Packing List
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.