Some standard content:
ICS 47.020
Registration No.: 11145-2003
Ship Industry Standard of the People's Republic of China
CB/T3950—2002
Elevating work platform for duckside2002
Published on November 20, 2002
Published by the Commission of Science, Technology and Industry for National Defense
2003—02—1 Sichuan implementation
This standard is proposed by China Shipbuilding Industry Corporation: Foreword
This standard is under the jurisdiction of China Shipbuilding Industry Corporation Comprehensive Technical and Economic Research Institute. 3. Standard editors: Chengxi Feibo Restaurant Selection!, China Shipbuilding Industry Corporation Comprehensive Technical and Economic Research Institute. 2. Drafters of this standard: Xie Ren'an, Bai Zhongqi, and Hua.
CB, T3960-2002
Dock wall operation vehicle
CB/T 39602002
This standard specifies the requirements, test methods, inspection rules and markings for electric hydraulic cover operation vehicles (abbreviated as wall vehicles).
This standard is applicable to the manufacture and inspection of hydraulic cover operation vehicles (abbreviated as wall vehicles). 2 Reference standards
The texts contained in the following standards also constitute the provisions of this standard through citation in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and the following standards may be the latest versions when using this standard. That is, /T271F7 Body fusion welding butt joint line cabinet rental quality classification 6/: 3783-1551 Marine low, electrical basic cost requirements CR/9465.2-196F High efficiency operation Technical conditions GB/T1039-993 Hydraulic system Working medium Solid Particles Soft Grade Code C7/T111?.-9 Marine hydraulic system General technology System cleaning 3 Product structure type
Dock wall truck soil fee mountain frame, boom, rotating mechanism, noise ditch, support, independent structure, upper work, and cab and other parts, then Figure 1:
Cab:
5- Rotary machine:
G- Support:
3- Upper work:
A frame:
1- Variable structure:
8- Walking machine
CH/T3950-2002
4 Requirements
4. 1 Performance
4.1.1 The main performance of the dock wagon is as follows: a) Working bucket lifting height II (original Figure 1 is determined by the actual design according to the ship's specifications): 1 Working bucket rated load 100kg:
Frame length! (See Figure 1: Determined by the design according to the actual docking force): Horizontal frame rotation angle ±°
Frame amplitude range -71
Channel amplitude time (from -40"~-70" standard) ±241 8~. 50 4: Accompanying energy waiting time (from 1991\~3 system 205 Cheng Tai travel speed (1012):
1) Working speed <25+2) m/r.in.
4.1.2 The difference between the boom and the boom 1. When the bucket is lifted under a certain load, it can work reliably within 151 mm after braking. The working height shall not exceed the maximum working height of the working position [5]. Working in any position, the working height shall be kept horizontal. 4.2 Safety
4.2.1 The steel structure of the vehicle wall shall have the required height and flexibility. Under the specified load and dynamic load, there shall be no deformation or other damage.
4.2.2 The height of the guardrail shall not be less than 1:1. The protective structure shall be able to withstand external forces in all directions. 4.2.3 When the hydraulic system fails, the hydraulic locks installed on the dock wall truck safety device should be able to effectively prevent the upper worker from lowering the bucket. 4.2.4 The limit of the variable amplitude mechanism, rotating mechanism, and variable speed mechanism of the dock wall truck should be able to effectively limit the operation of each mechanism. 1. The operation is limited to:
4.3 Drip pressure system
4.3.1 The pipes and fittings of the hydraulic system should be treated by the method of running before installation to remove rust, iron, live and other dirt. 4.3.2 The hydraulic system should not be allowed to have dirt, cement and cement. The system should be cleaned with oil according to the requirements of C3/T12.41956.
4.3.3 The oil pollution reduction level of the micro-pressure system must reach the requirements of B/T11039-1:19/16. 4.3.4 The system should be sealed and have good sealing performance, and the sealing test of 1.25 times the design pressure should be carried out. 4.4 Electrical appliances bZxz.net
4.4.1 The motors mentioned above should be of grade TF55 or above, and the absolute grade is R grade. 4.4.2 The performance of new control electrical appliances and distribution appliances should comply with the provisions of B/T3E31554. 4.5 Parts and components
All purchased and outsourced parts and components should have relevant certificates and should be inspected if necessary: they can be assembled only after they are qualified.
4.6 Appearance
The exterior of the vehicle should be smooth, the paint surface should be bright, the color should be bright, and there should be no burrs, cracks, bubbles and other defects on the surface of the guardrail. 47 Welding quality
The quality of the butt welding of the structure should not be lower than the grade guide seam in B/-3323-1H7. 4.8 Materials
The materials used in the vehicle should meet the requirements of the relevant material industry standards, and the material reports should be complete and the width should be straight. 2
5 Test method
5.1 Performance
CB/T39602002
5.1.1 The main performance of the vehicle should be tested under the conditions of rated load, rated load and rated load. The structure should meet the requirements of 4.1.! 5.1.2 Requirements for work 4: Under the negative load, lift 1.2-to the left of the work table, and keep 161:, and use the holding position to measure the three working buckets. The results should meet the requirements of 4.1 and 2. 5.2 Safety
5.2.1 Under 1.25 times the rated load, the static and dynamic load (running speed is 25=/3) test results of the dock wall car are tested. The requirements of 4.2.
5.2.2 The height of steel lifting inspection is prohibited: the simulation method is verified / T9465.2 [9th issue of 4.5.5, and external force is applied to the protective frame from the same direction, and the external force is observed after the fire protection frame is stimulated. 5.2.3 Use the simulated liquid to stop the system to produce an effective barrier agent to check the vehicle installation: the result should meet the requirements of 1.2.3. 5.2.4 Check the limit switches; the result should meet the requirements of 1.2.1. 5.3 Hydraulic system
5.3.1 Determine the solid particles of the main oil in the liquid: the result should meet the requirements of 4.3.3. 5.3.? 1.25 days under the design force, the hydraulic system is tested for 1% efficiency, maintained at 513, the result should meet the requirements of 4.3.4. 5.4 Electrical performance
5.4.1 Check the shell expansion resistance and insulation grade marks on the right electrical network. The result should meet the requirements of 4.4. ". 5.4.2 According to the test method specified in B/13788-1994, the performance of each collector and distributor is tested. The gauge should meet the requirements of 4.4.2. 5.5 Appearance and welding quality 5.5.1 Visual inspection of the appearance quality of the whole machine: the structure should meet the requirements of 2 and 6. 5.5.24 X-ray inspection of the internal quality of the main load-bearing components. The quality assurance and certificate of inspection materials should meet the requirements of 1.8. 6 Inspection rules 6. 1 Inspection classification: The inspection of automobiles is divided into two types: type inspection and type inspection: 6.2 Type inspection 6.2.1 Applicable scope Type inspection is the trial production and adjustment of new products or products. After production, if there are major changes in materials and processes that may affect product performance, and if there are major differences between the inspection results and the last type inspection, the country shall introduce some inspection agencies to carry out the inspection when required: 6 .2.2 Inspection Items
The type inspection items of the vehicle shall be in accordance with Table 1.
6.2.3 Number of Inspection Samples
The number of products to be inspected for the vehicle type shall be at least 6.2.4 Judgment Rules
If the inspection items of the vehicle type meet the requirements, the type inspection can be considered as qualified: If there are any items that do not meet the requirements, they can be re-inspected after repair. The inspection will be considered as qualified. 6.3 Factory Inspection
CB/T 3950—2002
6.3.1 Scope of Application
Each vehicle dealer shall submit the vehicle to the vehicle management department for inspection before production. 6.3.2 Inspection Items
The number of products to be inspected for the vehicle type shall be at least 6.3.3 Judgment rules
If all pre-inspections of the vehicle meet the requirements,
it is considered that the vehicle has passed the factory inspection. If there are any items that do not meet the requirements, re-inspection is allowed after the inspection. If there are still items that do not meet the requirements after the inspection, the vehicle is judged to be unqualified. Table 1: Inspection items
Strength of structure
Degree of protection
Non-system cleaning device
Liquid agent case level
Concentrated pressure system
Machine protection level and insulation level
7 Mark
Thoughts
Tested method
Book number
.1. 2. -1
Type inspection
Out! The dock wall vehicle should have operation signs, lubrication indicator signs, safety signs, etc. The signs should be clear and solid. 7.1 7.2 The nameplate should be installed in a conspicuous position. The nameplate should include the following information: a. Manufacturer name:
Product name and model
Rated load of working bucket:
Maximum degree and range of operation. Certification:
Issued! Year and month number:
Implementation standard code
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.