title>Packaging material—Coated antistatic polyethylene terephthalate(PET) sheet(coil) - BB/T 0082-2019 - Chinese standardNet - bzxz.net
Home > BB > Packaging material—Coated antistatic polyethylene terephthalate(PET) sheet(coil)
Packaging material—Coated antistatic polyethylene terephthalate(PET) sheet(coil)

Basic Information

Standard ID: BB/T 0082-2019

Standard Name:Packaging material—Coated antistatic polyethylene terephthalate(PET) sheet(coil)

Chinese Name: 包装材料 涂布型防静电聚对苯二甲酸乙二醇酯(PET)片材(卷材)

Standard category:Packaging Industry Standard (BB)

state:in force

Date of Release2019-05-02

Date of Implementation:2019-11-01

standard classification number

Standard ICS number:Packaging and transportation of goods >> 55.040 Packaging materials and auxiliary materials

Standard Classification Number:General>>Marking, packaging, transportation, storage>>A82 Packaging materials and containers

associated standards

Publication information

publishing house:China Standards Press

Publication date:2019-07-01

other information

drafter:Zhou Liquan, Li Ruilin, Huang Yahui, Wang Xu, Chen Baoyuan, Chen Pingxu

Drafting unit:Sichuan Yibin Plus Packaging Materials Co., Ltd., Suzhou Xinrihe New Materials Co., Ltd., Shenzhen Xingjinya Industrial Co., Ltd., Henan Zhongbao Technology Co., Ltd.

Focal point unit:National Packaging Standardization Technical Committee (SAC/TC 49)

Proposing unit:China Packaging Federation

Publishing department:Ministry of Industry and Information Technology of the People's Republic of China

competent authority:Ministry of Industry and Information Technology

Introduction to standards:

Standard number: BB/T 0082-2019 Standard name: Packaging material-Coated antistatic polyethylene terephthalate (PET) sheet (coil) Standard format: PDF Release time: 2019-05-02 Implementation time: 2019-11-01 Standard size: 1858K Standard introduction: Packaging industry standard of the People's Republic of China This standard is drafted in accordance with the rules given in GB/T1.1-2009 "Guidelines for Standardization Work Part 1: Structure and Preparation of Standards". Please note that some of the contents of this document may involve patents. The issuing agency of this document does not assume the responsibility for identifying these patents. This standard is proposed by the China Packaging Federation. This standard is under the jurisdiction of the National Technical Committee for Packaging Standardization (SAC/TC49). 1 Scope This standard specifies the classification, requirements, test methods, inspection rules, marking, packaging, transportation and storage of coated antistatic polyethylene terephthalate (PET) sheets (rolls). This standard is applicable to antistatic sheets and rolls produced by coating antistatic coatings with PET substrates of 1.0 mm or less in thickness). Coated antistatic materials with thicknesses above 1.0 mm and other substrates can be used as a reference. 2 Normative references The following standards are essential for the application of this standard. For any dated reference standard, only the dated version applies to this standard For any undated reference standard, the latest version (including all amendments) applies to this standard GB/T191 Pictorial marking for packaging storage and transportation GB/T1040.3 Determination of tensile properties of plastics Part 3: Test conditions for films and sheets GB/T1410 Test method for volume resistivity and surface resistivity of solid insulating materials B/T2035 Plastic terms and definitions GB/T2410-2008 Determination of light transmittance and haze of transparent plastics B/T2828.1 Sampling inspection procedure by attributes Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL) GB/T2918 Conditioning and testing of plastic specimens Standard environment for testing GB/T6672 Determination of thickness of plastic film and sheet by mechanical measurement GB/T6673 Determination of length and width of plastic film and sheet GB/T7706-2008 Letterpress decoration printing GB/T9639.1 Test method for impact resistance of plastic film and sheet Free-falling dart method Part 1: Ladder method GB/T15463 Static electricity safety terminology GB/T26125 Determination of six restricted substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated diphenyl ethers) in electronic and electrical products GBT26572 Limit requirements for restricted substances in electronic and electrical products SJ/T10694 General specification for anti-static testing of electronic product manufacturing and application systems
This standard specifies the classification, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of coated antistatic polyethylene terephthalate (PET) sheets (rolls). This standard applies to antistatic sheets (rolls) produced by coating antistatic coatings with PET substrates of 1.0 mm or less in thickness. Coated antistatic materials with thicknesses above 1.0 mm and other substrates can be used as a reference.


Some standard content:

ICS55.040
Packaging Industry Standard of the People's Republic of China
BB/T0082—2019
Packaging material
Coated antistatic
Polyethylene terephthalate
(PET) sheet (coil)
Packaging material-Coated antistatic polyethyleneterephthalate(PET)sheet(coil)2019-05-02Published
Published by the Ministry of Industry and Information Technology of the People's Republic of China
Implementation on 2019-11-01
BB/T0082—2019
This standard was drafted in accordance with the rules given in GB/T1.12009 "Guidelines for Standardization Part 1: Structure and Writing of Standards". Please note that some contents of this document may involve patents, and the issuing organization of this document does not assume the responsibility for identifying these patents. This standard is proposed by the China Packaging Federation. This standard is under the jurisdiction of the National Packaging Standardization Technical Committee (SAC/TC49). The main drafting units of this standard are: Sichuan Yibin Plus Packaging Materials Co., Ltd., Suzhou Xinhe New Materials Co., Ltd., Shenzhen Shanxing Jinya Industrial Co., Ltd., and Henan Zhongbao Technology Co., Ltd. The main drafters of this standard are: Zhou Liquan, Li Ruilin, Huang Yahui, Shi Xu, Chen Baoyuan, Chen Pingxu 1 Scope
Packaging materials Coated anti-static
Polyethylene terephthalate
(PET) sheet (roll)
BB/T 0082—2019
This standard specifies the classification, test methods, inspection rules, marking, packaging, transportation and storage of coated anti-static polyethylene terephthalate (PET) sheet (roll). This standard applies to antistatic sheets (rolls) produced by coating antistatic coatings with PET substrates of 1.0 mm or less in thickness. Coated antistatic materials with thicknesses above 1.0 mm and other substrates can be used as a reference. 2 Normative references
The following standards are essential for the application of this standard. For all dated references, the version with the date applies to this standard. For undated reference standards, the latest version (including all amendments) shall apply. GB/T191 Graphical labeling for packaging, storage and transportation GB/T1040.3 Determination of tensile properties of plastics Part 3: Test conditions for films and sheets GB/T1410 Test methods for volume resistivity and surface resistivity of solid insulating materials GB/T 2035 Plastic terms and definitions G13/T2110—2008 Determination of light transmittance and haze of transparent plastics GB/T 2828.1 Sampling procedures for inspection by attributes Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQI) GR/T2918 GB/T 6672 GB/T 6673
Standard environment for conditioning and testing of plastic specimensMeasuring method for thickness of plastic films and sheetsMeasuring length and width of plastic films and sheetsGB/T77C6—2008Determination of length and width of letterpress printingGB/T 9639.1
GB/T15463
GB/T 26125
GB/T26572
SI/T 10694
3 Terms and definitions
Test method for impact resistance of plastic film and sheeting-Part 1: Terminology for electrical and electronic safety
Determination of six restricted substances (lead, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated phenyls) in electrical and electronic products Limit requirements for restricted substances in electrical and electronic products General specification for anti-static testing of electronic product manufacturing systems GB/T 2035 and the terms and definitions established in GB/T 15463 are applicable to this document 4 Classification
According to the surface charge, it is divided into conductive type and static dissipative type 1
BB/T 0082—2019
Dimension deviation
The dimension deviation shall comply with the provisions of Table 1.
Table 1 Dimensional deviation
0.202m3.0.40mm
0.4cmms.8c.0.x0mm
0.8cmm81.0mm
Applicable to sheets, no requirement for coils. bzxZ.net
Appearance quality
Appearance quality should comply with the provisions of Table 2.
Table 2 Appearance quality
Project name
Pieces/(30 cm/3C cm)
pcs/3ccmX30cm)
pcs/(30cmX30cm)
.5mz≤diameter more than 2.0mm
diameter ≥2.0mm
9.5mmdiameter ≤2.cmm
vertical diameter 2.0mm
0.5mm≤diameter 2cmm
cracks, perforations, missing edges, precipitation, oil stains and wrinkles
water marks, clouds, scratches, dirt
roll 50kg
number of joints per roll
roll weight 5℃kg
end surface flatness
cut edge
abnormal points include black spots, gate spots, miscellaneous spots, etc. Infant request
Not allowed
Unknown record
Unknown record"
No more than 1 joint, each section should be at least 20 meters long, and products with press heads should be marked at the joints
Should be flat and smooth, without obvious burrs or waves. If it is not obvious when measured at a distance of 50cm under natural light (not direct sunlight) or under a fluorescent lamp, it is considered not obvious. 5.3 Physical and mechanical properties
The physical and mechanical properties shall comply with the requirements of Table 3. Item
Light transmittance?
Tensile strength
Measurement of damage to leather
, only for transparent products.
5.4 Antistatic performance
Nominal strain at break
Table 3 Physical and mechanical properties
0.20mms.a.0.40mm
0.40 mmse-.0.80 mm
6.80mm%8.1.0mm
Antistatic performance shall comply with the provisions of Table 4
Table 4 Antistatic performance
Concentrated surface resistance:
Static pressure time
Friction resistance
Limited requirements for restricted substances
Conductive type
Should comply with the relevant provisions of GB/T26572
6 Test method
Test environment
BB/T 0082—2019
Static dispersion type
1X1001X10
Not more than 2 orders of magnitude
The state adjustment of the sample shall be carried out in accordance with the provisions of GB/T2918, the state adjustment temperature is (2312)℃: relative humidity is (50~10)%, and there is no conductive dust in the air and no strong external electromagnetic field, the state adjustment time is not less than 24h, and the test is carried out under this condition, and the appearance quality
is tested by natural light source or 1D50 light source. The arbitration shall meet the requirements of [50 light source 6.2.2
The inspection eye shall be inspected by the moonlight method, and the distance between the inspection eye and the inspection part shall be 300mm-~5c0mm. 3
BB/T 0082—2019
6.2.3 The end surface flatness shall be inspected by a steel ruler with an accuracy of 0.5mm. 6.2.4 Impurities such as spots, black spots, bubbles and white spots shall be measured with tools with an accuracy of not less than 0.1mm. 6.3 Dimensional deviation
6.3.1 Length and width
Use a measuring tool with an accuracy of 0.5mm and measure in accordance with the provisions of GB/T6673. 6.3.2 Thickness
Use a measuring tool with an accuracy of 0.001mm and measure in accordance with the provisions of GB/T6672. 6.4 Physical and mechanical properties
6.4.1 Transmittance and haze
Measured in accordance with the provisions of G1B/T2410-2008 Method A. 6.4.2 Tensile strength and nominal strain at break
Measured in accordance with the provisions of GB/T1040.3, using type 5 specimens, tensile speed (50±5) mm/min 6.4.3 Impact damage quality
Measured in accordance with the provisions of GB/T9639.1.
6.5 Antistatic performance
6.5.1 Surface resistance
Use a surface resistance tester or test according to the provisions of GB/T1410. In arbitration, the provisions of GB/T1110 should be used for testing. 6.5.2
Static voltage decay time
According to the provisions of SJ/T10691.
6.5.3 Friction resistance
According to 6.8, and then test the surface resistance after rubbing according to the provisions of 6.5.1. The limit requirements for restricted substances shall be carried out according to the provisions of GB/T26125.
7 Inspection rules
7.1 Batch
The same batch of substrates and products produced continuously under the same coating process conditions are a batch, and the weight of each batch shall not exceed 50t: 2 Factory inspection items
The factory inspection items are the surface resistance in 5.15.2, 5.3 and 5.4. 4
Type inspection items
BB/T 0082—2019
The type inspection items are all items in Chapter 5. Generally, it shall be conducted at least once a year: Type inspection shall be conducted in any of the following circumstances:
Appraisal of new products for production;
After formal production, if there are significant changes in structure, process, or materials; In normal production, an inspection shall be conducted periodically or after a certain amount of production has been accumulated to assess the stability of product quality; When the product is discontinued for half a year or more and production is resumed; When there is a significant difference between the factory inspection result and the last type inspection result; When the national quality supervision agency or user makes a request, sampling and judgment rules
The normal inspection secondary sampling plan for dimensional deviation and appearance quality is carried out in accordance with GB/T2828.1, the inspection level is II, and the acceptance quality limit (AQI) is 6.5. Sampling inspection shall be conducted in accordance with the provisions of Table 5, and physical Mechanical properties, anti-static properties and restricted substances limit requirements, take a roll of sheet from each batch of products for inspection Table 5
26--55
9:-~150
131---280
281~-530
56122C0
1201--3200
Sampling and judgment plan for dimensional deviation and appearance quality inspection Sample size #
Cumulative sample size
Acceptance number Ac
Rejection number Re
BB/T0082—2019
5 Judgment of inspection results
7.5.1 Dimensional deviation, appearance quality, if one of the right items is unqualified, the roll of product is judged to be unqualified. The judgment of qualified batches is carried out according to Table 5. 7.5.2 Physical properties, anti-static properties and restricted substance limits shall all comply with the requirements of this standard; if there are unqualified items, double samples shall be drawn from the original batch of products and the unqualified items shall be retested. If the retest is still unqualified, the batch of products shall be unqualified. 7.5.3 When the products are qualified according to 7.5. and 7.5.2, the batch of products shall be judged as qualified products. 8 Marking, packaging, transportation and storage
8.1 Marking
The marking shall comply with the provisions of GB/T191. The product shall include a product certificate when leaving the factory: the product certificate shall include the product name, product number, product specifications, quantity, production date, batch number, manufacturer name, etc. 8.2 Packaging
The product shall be treated with moisture-proof and dust-proof treatment, and the packaging format shall be agreed upon by the supply and demand parties. 8.3 Transportation
The product should be loaded and unloaded lightly during transportation to prevent heavy pressure, lateral pressure, rolling, falling and collision with hard objects, and to prevent exposure to the sun and rain. Avoid transportation under high humidity.
8.4 Purchase and storage
The product should be stored in a clean and cool warehouse to avoid direct sunlight. It should be kept at room temperature and humidity. It should be no less than 2m away from heat sources and avoid contact with organic solvents. Under normal storage conditions, the storage period is preferably half a year from the date of birth. If it exceeds half a year, it needs to be re-inspected6
BB/T0082-2019
People's Republic of China Packaging
Industry Standard
Packaging Material Coated Antistatic
Polyethylene Terephthalate
(PET) Sheet (Roll)
BB/T 0082—2019
Published and distributed by China Standards Press
No. 2, Hepingdan West Street, Chaoyang District, Beijing (00029) No. 16, Erlihe North Street, Xiyu District, Beijing (100045) Website: spc.org.cn
Service hotline: 100-168-0010
2619? Edition
Book number: 155066: 2-34426
Copyright reserved
Infringements will be investigated
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.