title>GB 17429-1998 General technical requirements for fire display panels - GB 17429-1998 - Chinese standardNet - bzxz.net
Home > GB > GB 17429-1998 General technical requirements for fire display panels
GB 17429-1998 General technical requirements for fire display panels

Basic Information

Standard ID: GB 17429-1998

Standard Name: General technical requirements for fire display panels

Chinese Name: 火灾显示盘通用技术条件

Standard category:National Standard (GB)

state:in force

Date of Release1998-07-15

Date of Implementation:1999-06-01

standard classification number

Standard ICS number:13.200.20

Standard Classification Number:Medicine, Health, Labor Protection>>Fire Protection>>C81 Fire Monitoring, Alarm and Fire Dispatch System

associated standards

Publication information

publishing house:China Standards Press

ISBN:155066.1-15300

Publication date:2004-04-15

other information

Release date:1998-07-15

Review date:2004-10-14

Drafting unit:Shenyang Fire Science Research Institute of Ministry of Public Security

Focal point unit:National Fire Protection Standardization Technical Committee

Publishing department:State Administration of Quality and Technical Supervision

competent authority:Ministry of Public Security

Introduction to standards:

This standard specifies the technical requirements, test methods, classification and marking of fire display panels. This standard applies to fire display panels installed in general industrial and civil buildings. Fire display panels with special performance installed in other environments should also refer to this standard, except for special requirements that should be separately specified by relevant standards. GB 17429-1998 General Technical Requirements for Fire Display Panels GB17429-1998 Standard Download Decompression Password: www.bzxz.net

Some standard content:

GB17429—1998
As an important part of the automatic fire alarm system, the fire display panel is increasingly widely used in industrial and civil buildings, playing an important role in protecting people's lives and property. However, there is no unified technical standard for fire display panels in my country. Manufacturers often design and produce products according to user requirements or enterprise standards, resulting in different product performance and quality, which brings great difficulties to product quality supervision and inspection, and it is difficult to ensure the reliability of product quality and performance. For this reason, this standard is formulated to provide a technical basis for the production, inspection and quality supervision of such products.
This standard includes six parts: scope, reference standards, technical requirements, test methods, product classification, and marking. The setting of environmental test items and the provisions of test methods are all referred to the relevant provisions of GB16838--1997 "Environmental Test Methods and Severity Levels for Fire Electronic Products". This standard is a mandatory standard. After the implementation of this standard, fire display panels used in general industrial and civil buildings should be inspected according to this standard.
This standard is proposed by the Ministry of Public Security of the People's Republic of China. This standard is under the jurisdiction of the Sixth Sub-Technical Committee of the National Technical Committee for Fire Protection Standardization. This standard was drafted by the Shenyang Fire Science Research Institute of the Ministry of Public Security. The main drafters of this standard are: Song Xiwei, Wang Yan'e, Ding Hongjun, Guo Tienan, and Zhuang Binghua. 4.95
1 Scope
National Standard of the People's Republic of China
General Technical Conditions for Fire Indicating Panels
General Technical Conditions for Fire Indicating Panels This standard specifies the technical requirements, test methods, classification and marking of fire indicating panels. GB 17429-- 1998
This standard applies to fire indicating panels installed in general industrial and civil buildings. Fire indicating panels with special performance installed in other environments should also refer to this standard, except for special requirements that should be separately specified by relevant standards. 2 Referenced Standards
The provisions contained in the following standards become the provisions of this standard through reference in this standard. When this standard was published, the versions shown were valid. All standards are subject to revision. Parties using this standard should investigate the possibility of using the most recent editions of the following standards. GB2423.1-89 Basic environmental test procedures for electrical and electronic products Test A: Low temperature test method GB2423.2-89 Basic environmental test procedures for electrical and electronic products Test B: High temperature test method GB/T2423.3--93 Basic environmental test procedures for electrical and electronic products Test Ca: Steady state damp heat test method GR/T2423.5-1995 Basic environmental test procedures for electrical and electronic products Part 2: Test method Test a and guidance: Yang Street
GB/T2423.10--1995
Basic environmental test procedures for electrical and electronic products Part 2: Test method Test Fc and guidance: Moving (sinusoidal)
GB/T6113-1995
3 Technical requirements
Specifications for radio interference and immunity measuring equipment 3.1 The DC operating voltage of the fire display panel may preferably be 24V. 3.2 Overall performance
3.2.1 The fire display panel should have the following basic functions. 3.2.1.1 The fire display panel can only receive signals from the fire alarm controller, and should not provide power to fire detectors, manual alarm buttons and other detection parts.
3.2.1.2 It can receive fire alarm signals from the fire alarm controller, send out sound and light alarm signals, indicate the location of the fire, and maintain them: the light alarm signal cannot be manually eliminated before the fire alarm controller is reset, the alarm signal should be manually eliminated, and there should be a mute indication, but it should be able to restart when the fire alarm signal is input again. 3.2.1.3 For the fire display panel powered by the fire alarm control panel, the fire display panel shall be able to send out an audible and visual fault signal that is clearly different from the fire alarm signal within 100 seconds and indicate the type of fault when any of the following circumstances occurs: a) the main power supply is cut off; b) the connection line between the charger for charging the backup power supply and the backup power supply is broken or short-circuited; c) the connection line between the backup power supply and its load is broken or short-circuited, or the voltage of the backup power supply alone is insufficient to ensure the normal operation of the fire display panel.
Approved by the State Administration of Quality and Technical Supervision on July 15, 1998 496
Implementation on June 1, 1999
GB17429-1998
The audible fault signal shall be manually eliminated and have a mute indication, and the optical fault signal shall be maintained before the fault is eliminated; during the fault period, if there is fire alarm information input, the fire display panel shall be able to send out a fire alarm signal. 3.2.1.4 The fire display panel (via the controller) shall be able to perform functional checks on all indicator lights, displays and audio devices on its panel.
The operating functions of the fire display panel shall be classified according to the provisions of Table 1. Level I
Functions that are allowed to be operated by everyone;
Functions that are allowed to be operated by specialized personnel.
Operation items
Eliminate the sound signal of the fire display panel
Open and close the fire display panel
Reset the fire display panel
Adjust the timing device
Operation level
Note: P-prohibited, optional, M-operable by operators at this level. Entering the Level I working state shall use a key or operation code Level 1
3.2.1.6 The fire display panel that is not powered by the fire alarm controller shall have a power conversion function. When the main power supply is cut off, it can automatically switch to the backup power supply; when the main power supply is restored, it can automatically switch to the main power supply; the working status of the main and backup power supplies should be indicated, the main power supply should have overcurrent protection measures, and the switching of the main and backup power supplies should not cause the fire display panel to send out a fire alarm signal. The capacity of the main power supply should be able to ensure that the fire display panel can work continuously for 4 hours under maximum load conditions (all parts are in fire alarm status). 3.2.1.7 The delay of the fire display panel for receiving the fire alarm input signal should not exceed 3s. 3.2.1.8 The fire display panel with a timing device should be able to display or record the fire alarm time, and its diary time error should not exceed 30s. 3.2.2 The fire display panel should be able to withstand the various tests under the climatic and environmental conditions specified in Table 2, and the performance during and after the test should meet the requirements of the relevant tests in Chapter 4 of this standard. Table 2
Test name
High temperature test
Low temperature test
Steady-state damp heat test
Low-temperature storage test
Test parameters
Duration
Duration
Relative humidity
Duration
Duration
Climate environment test
Test conditions
40°℃
1. Operating state
De-energized state 14h
Normal monitoring state 2h
De-energized state 14h
Normal monitoring state 2 h
Normal monitoring state
De-energized state
3.2.3 The fire display panel shall be able to withstand the tests under the mechanical environmental conditions specified in Table 3. The performance during and after the test shall meet the requirements of the relevant tests in Chapter 4 of this standard. 197
Test name
Vibration (sinusoidal) test
Impact test
Collision test
Note: m is the mass of the sample,
GB 17429--1998
Table 3 Mechanical environment test
Test parameters
Frequency cycle range
Acceleration amplitude
Sweep rate
Hold time at dangerous frequency
Number of sweep cycles on each axis
Vibration direction
Acceleration (g)
Pulse duration
Number of impacts
Collision energy
Number of magnetic impacts
Test conditions
10150-10Hz
0.1g.0.5g
1 octave/min
X, Y, 2
300~20m
6 surfaces, 18 times
Sine wave
0. 5 J±0. 04
3 times for each vulnerable point
Working state
Normal monitoring state
De-energized state
De-energized state
Normal monitoring state
3.2.4 The fire display panel shall be able to withstand the various tests under the electrical interference conditions specified in Table 4. The performance during and after the test shall meet the requirements of the relevant tests in Chapter 4 of this standard. Table 4 Electrical dry environment test
Test name
Radiated electric field test
Electrostatic discharge test
Electrical transient pulse test
Power supply transient test
Test parameters
Frequency range
Effective voltage
Number of discharges
Transient pulse current
Power supply transient mode
Number of applications
Application mode
Test conditions
1 MHz~1 GHz
AC power line 2kV,
other connecting lines 1kv
positive, negative
each time 1min, 3 times in total
power on 95-power off 18
500 times
times/minin
working status
normal status
normal visual status
normal monitoring status
3.2.5 When the fluctuation range of the AC power supply voltage does not exceed ±19% of the rated voltage (220 V) and the frequency deviation does not exceed 1% of the standard frequency 15
(50Hz), the fire display panel should be able to work normally. 3.2.6 The insulation resistance between the external live terminals and the housing, and between the power plug (or power wiring terminal) and the housing of the fire display panel with insulation requirements shall be greater than 20M0 and 50M0 respectively under normal atmospheric conditions. The above-mentioned parts shall also be subjected to a withstand voltage test of 1500V (when the rated voltage exceeds 50V) or 500V (when the rated voltage does not exceed 50V) AC for 1 minute according to the rated voltage withstand frequency of 50Hz. The performance during and after the test shall meet the requirements of the relevant tests in Chapter 4 of this standard. 3.2.7 The fire display panel shall withstand the various tests specified in Chapter 4 of this standard and meet all the requirements of this standard. 3.3 Performance of main components
3.3.1 General requirements
GB17429-1998
The main components of the fire display panel shall adopt standardized products that meet the relevant national standards and shall meet the following relevant requirements. 3.3.2 Indicator lights
3.3.2.1 Should be color-coded: red for fire alarm signals, yellow for fault signals, and green for normal power supply operation. 3.3.2.2 Under normal ambient light conditions, the indicator lights should be clearly visible at a distance of 3m. The alphanumeric display should be readable at 0.8m under ambient light intensity of 0.1~5001x. 3.3.3 Electronic components
should be treated with three protections (moisture-proof, fire-proof, and salt spray-proof), and the parameters should meet the requirements of maximum operating voltage and maximum operating current. 3.3.4 Fuse
The rated current of fuses or other overcurrent protection devices used in power supply lines should generally not be greater than twice the maximum operating current of the fire display panel. The parameter values ​​should be clearly marked near the fuses or other overcurrent protection devices. 3.3.5 Sound devices
Under rated working voltage, the sound pressure level (A-weighted) of the internal sound devices at a distance of 1m from the sound devices should be above 65dB and below 115dB. It should be able to make a sound under 85% rated working voltage. 3.3.6 Backup power supply
3.3.6.1 If the backup power supply uses a battery, the battery capacity should ensure that the fire display panel can work for 30min under maximum load after working for 8h under normal monitoring state.
3.3.6.2 The positive connection wire of the power supply is red, and the negative is black or blue. 3.3.6.3 Under the condition of not exceeding the limit discharge specified by the manufacturer, the battery should be able to be charged and restored to the positive state within 48h. 3.3.6.4 Non-sealed batteries should not be used. 4 Test methods
4.1 Fire display panel test outline
4.1.1 The test procedure of the fire display panel is shown in Table 5. Table 5 Test procedure
Test procedure
Sequence number
Test items
Main component inspection test
Basic function test
Power-on test
Power supply test
Electrical transient pulse test
Power supply transient test
Insulation resistance test
Withstand voltage test
Electrostatic discharge test
Note: V indicates that the sample is subjected to this test. 1
Specimen number
Item number
Test procedure
Test items
Radiated electromagnetic field test
High temperature test
Low temperature test
Vibration (sinusoidal) test
Impact test
Steady-state damp heat test
Low temperature storage test
Collision test
Specimen number
4.1.2 The tests specified in this standard are type tests. The number of test product samples shall be no less than three and shall be numbered before the test. 4.1.1 In Table 5, tests 1 to 10 shall be conducted before tests 11 to 17; tests 1 and 2 must be conducted first. 4.1.3 The fire display panel under test (hereinafter referred to as the sample) shall be inspected for appearance before the test. The test can be carried out only when it meets the following requirements: a) There is no corrosion, coating peeling, blistering, obvious scratches, cracks, burrs and other mechanical damage on the surface; b) The fastening parts are not loose, and the control mechanism should be flexible; c) The text symbols and signs are clear.
GB 17429-1998
4.1.4 If there is no explanation in the relevant provisions, all tests shall be carried out under the following normal atmospheric conditions: temperature: 15~35℃;
Relative humidity: 45%~75%;
Atmospheric pressure: 86~106kPa.
4.1.5 If there is no explanation in the relevant provisions, the tolerance of the spare test data is ±5%. 4.1.6 When it is not feasible to test a large sample as a whole, it is allowed to divide the sample into several parts for testing. 4.2 Main component inspection test
4.2.1 Purpose
Inspect the performance of the main components of the fire display panel. 4.2.2 Requirements
The performance of the main components of the fire display panel shall meet the requirements of 3.3. 4.2.3 Methods
4.2.3.1 Inspect and record the function markings of each switch and button of the sample. 4.2.3.2 Put the sample in the fire alarm state, measure and record the sound pressure level of the sample sound alarm signal. 4.2.3.3 Inspect and record the parameter markings of the fuse and other overcurrent protection devices and their actual capacity values. 4.2.3.4 Inspect and record the usage, color identification, visibility and function markings of the indicator lights and displays. 4.3 Basic function test
4.3.1 Purpose
Inspect the basic functions of the fire display panel.
4.3.2 Requirements
The basic functions of the fire display panel shall meet the requirements of 3.2.1. 4.3.3 Method
4.3.3.1 Connect the fire display panel and the corresponding fire alarm controller, and turn on the power supply to put the sample in the normal monitoring state. 4.3.3.2 Put any circuit in the fire alarm state, observe and record the sound and light alarm signals of the sample, and observe and record the timing if there is a timing device.
4.3.3.3 Put any circuit in the fire alarm state, first manually eliminate the sound alarm signal; then put the other circuit in the fire alarm state, observe and record the sound and light alarm signals of the sample. 4.3.3.4 When the sample is in the fire alarm state, first cancel the input fire alarm signal, then manually reset the sample, observe and record the sound and light alarm signals of the sample.
4.3.3.5 For the sample that is not powered by the fire alarm controller, put it in the three fault states of 3.2.1.3 respectively, and then operate the manual elimination and reset mechanism in turn, observe and record the sound and light signals of the sample and the indication of the fault type. 4.3.3.6 When the sample is in a faulty state, first eliminate the fault, then operate the manual reset mechanism (do not operate the automatic reset), observe and record the sound and light alarm signals of the sample.
4.3.3.7 When the sample is in a faulty state, put one circuit in a fire alarm state, observe and record the sound and light signals of the sample. 4.3.3.8 Operate the sample self-test and indicator light and display inspection mechanism, observe and record the sound and light alarm signals of the sample. 4.3.3.9 Check and record the classification of the sample operation function (performed during the first basic function test). 4.3.3.10 For the fire display panel that is not powered by the fire alarm controller, cut off the main power supply, then restore it to normal, observe and record the conversion of the main power supply and the backup power supply and the changes of the power indicator light 4.3.3.11 For the samples not powered by the fire alarm controller, switch the main power supply to the backup power supply and repeat the test process of 4.3.3.2~4.3.3.9.
4.4 Power-on test
4.4.1 Purpose
GB17429-1998
To test the stability of the operation of the fire display panel under normal atmospheric conditions. 4.4.2 Requirements
4.4.2.1 During the test, the sample should not send out fire alarm and fault signals. 4.4.2.2 After the test, the performance of the sample should meet the requirements of Article 4.3.2. 4.4.3 Method
Connect the sample to the fire alarm controller according to the requirements of the normal blue-vision state. Turn on the power supply to put the sample in the normal monitoring state and run continuously for 45 days. At the end of the test, carry out basic function test on the sample according to the provisions of Article 4.3. 4.5 Power supply test
4.5.1 Purpose
To test the adaptability of the fire display panel to the fluctuation of the AC power supply voltage and the load change, as well as the capacity of the power supply. 4.5.2 Requirements
4.5.2.1 The main power supply shall meet the requirements of 3.2, .1.6 and 3.2.5. 4.5.2.2 After the main power supply test, the performance of the sample shall meet the requirements of 4.3.2. 4.5.2.3 The backup power supply shall meet the requirements of 3.3.6.1. 4.5.3 Method
4.5.3.1 Main power supply test
&) Turn on the power supply of the test device, adjust the test device so that the input voltage of the sample is the rated working voltage, the rated working voltage is reduced by 15% and increased by 10%, respectively, and observe and record the working conditions of the sample. b) Power the sample with the main power supply and make it work continuously for 4 hours under the maximum load condition, observe and record the working condition of the sample; then restore the sample to the monitoring state, and conduct basic functional test on the sample according to the provisions of Article 4.3. 4.5.3.2 Backup power supply test
Power the sample with the backup power supply and make it work for 8 hours under the normal monitoring state, and make it work for 30 minutes under the maximum load condition; then cut off the sound alarm signal, make any circuit in the dry state in the fire alarm state, observe and record the working condition of the sample 4.5.3.3 At the end of the test, conduct basic functional test on the sample according to the provisions of Article 4.3. 4.6 Electrical transient pulse test
4.6.1 Purpose
To test the ability of the fire display panel to resist electrical transient pulse interference. 4.6.2 Requirements
4.6.2.1 During the test, the sample should not issue a fire alarm and an irreversible fault signal. 4.6.2.2 After the test, the performance of the sample should meet the requirements of Article 4.3.2. 4.6.3 Method
4.6.3.1 Connect the sample to the fire alarm controller according to the requirements of the normal monitoring state. Turn on the power supply to put the sample in the normal monitoring state. 4.6.3.2 Apply a positive and negative polarity transient pulse voltage of 1000V±100V and a frequency of 5kHz±1kHz to the external connection line of the sample (except the AC power supply) (see Figure 1 for the waveform). Apply the transient pulse voltage for 15s every 300ms (see Figure 2). The transient pulse voltage is applied for 6011°s each time, and is applied three times in total. The time interval between applying two transient pulse voltages is 10s. During the test, monitor whether the sample sends out fire alarm and fault signals.
4.6.3.3 For fire display panels powered by non-fire alarm controllers, apply a positive and negative polarity transient pulse voltage of 2000V ± 200V and a frequency of 2.5kHz ± 0.5kHz to the AC power line of the sample (see Figure 1 for waveform), apply the transient pulse voltage for 15ms every 300ms (see Figure 2), and apply the transient pulse voltage for 60! s each time, apply three times in total, and the time interval between two transient pulse voltages is 10S. During the test, monitor whether the sample sends out fire alarm and fault signals. 4.6.3.4 After the test, perform basic function tests on the sample in accordance with the provisions of Article 4.3. 501
4.6.4 Test equipment
5ns±30%
GB 17429-1998
50ns±30%
Figure 1 Single pulse waveform when 500 load
Transient pulse
Repetition period (depends on transient pulse voltage) The number of pulses is determined by the color frequency
Figure 2 Group of transient pulse waveforms
Transient generator: output transient pulse voltage 1 000 V±100 V, 2 000 V±200 V. Pulse frequency 5 kHz±1 kHz, 2.5kHz±0.5kHz, output impedance 50Ω, output 15ms transient pulse voltage every 300ms, polarity is positive and negative. Its electrical schematic is shown in Figure 3. The coupling/decoupling network and coupling device used during the test are shown in Figures 4 and 5. 4.7 Power supply transient test
4.7.1
Test the fire display panel's ability to resist power supply transient interference. 4.7.2 Requirements
4.7.2.1 During the test, the sample should not issue a fire alarm or an irreversible fault signal. 4.7.2.2 After the test, the sample performance should meet the requirements of 4.3.2. 502
High voltage shaft
Connector
4.7.3 Method
GB17429-1998
Transient generation control
U High voltage power supply, R Charging shoe, C—Energy storage capacitor R—Pulse shaping resistor; Rm Impedance matching resistor: Ca-DC blocking capacitor
Figure 3 Electrical schematic diagram of electrical transient pulse generator
Signal from transient pulse generator
2>100xH
Filter
Decoupling part
Iron feces
Ce=33n|| tt||Coupling part
Figure 4 Coupling/decoupling network L2 for AC power line test
Reference ground terminal
Dimension unit: mm
Coupling plate
The grounding plate area is at least
Insulating leg
1m\ and each side is 0.1m longer than the coupling plate
Figure 5 Coupling device test specimen for other external connection lines
High voltage coaxial
Connection connector
For fire display panels that are not powered by fire alarm controllers, connect the specimen to the fire alarm controller according to the normal monitoring state requirements. Connect the specimen to the power transformer test device and place the specimen in the normal blue viewing state first. Turn on the test device and make the main power supply of the sample continuously disconnect for 500 times according to the fixed procedure of "power on (9s)--power off (1s)", observe and record the sound and light alarm signals of the sample.
After the test, carry out basic function test on the sample according to the provisions of Articles 4 and 3.4.7.4 Test equipment
A power supply device that can produce the test conditions that meet the requirements of Articles 4 and 7.3.4.8 Insulation resistance test
4.8.1 Purpose
To test the insulation of the fire display panel.
4.8.2 Requirements
4.8.2.1 The insulation resistance value between the external live terminals of the sample with insulation requirements and the housing should be greater than 20M2.4.8.2.2 The insulation resistance value between the power wiring terminals of the sample and the housing (the power switch is in the avoidance position, but the power wiring terminals are not connected to electricity) should be greater than 50Mm.
4.8.3 Method
Through Insulation resistance test device: Apply 500V±50V DC voltage to the following parts of the sample respectively for 60s±5s, and then measure its insulation resistance value.
a) Between the external live terminals with insulation requirements and the housing; b) Between the power terminals and the housing (the power switch is in the on position, but the power terminals are not connected to electricity). During the test, it should be ensured that there is reliable contact at the contact points, and the insulation resistance between the leads should be large enough to ensure correct readings. 4.8.4 Test equipment
Insulation resistance test device that meets the following technical requirements (in the absence of special test equipment, a megohmmeter or shaker can also be used for testing)
Test voltage: 500V±50Vn;
Measuring range: 0500MQ;
Minimum division: 0.1M2;
Timing: 60s±5s.
4.9 Withstand voltage test
4. 9.1 Purpose
To test the pressure resistance performance of the fire display panel.
4.9.2 Requirements
4.9.2.1 During the test, the sample should not have surface arcing, sweeping effect, corona and breakdown. 4.9.2.2 After the test, the performance of the sample should meet the requirements of 4.3.2. 4.9.3 Methods
Use the withstand voltage test device to apply a test voltage of 50Hz, 1500V±150V (when the rated voltage exceeds 50V) or 50Hz, 500V±50V (when the rated voltage does not exceed 50V) to the following parts of the sample at a voltage rise rate of 100-~500V/s. a) Between all external live terminals with insulation requirements and the housing; b) Between the power terminal and the housing (the power switch is in the on position, but the power terminal is not connected to electricity). Continue for 60s5$, observe and record the phenomena that occur during the test. After the test, the voltage is gradually reduced to a value lower than the rated voltage at a voltage reduction rate of 100~500V/s, and then the power can be turned off: Then, the basic function test of the sample is carried out in accordance with the provisions of Article 4.3. 4.9.4 Test equipment
A withstand voltage test device that meets the following technical requirements. Test power supply: voltage 01500V (effective value) continuously adjustable. Frequency 50Hz, short-circuit current 10A (effective value): 504
Rise (fall) voltage rate: 100~500V/s; recording time: 60s±5s
4.10 Electrostatic discharge test
4.10.1 GB17429-1998
Inspect the adaptability of the fire indicator panel to the electrostatic discharge caused by the contact of static electricity personnel and objects. 4.10.2 Requirements
4.10.2.1 During the test, the sample should not issue a fire alarm and an irreversible fault signal. 4.10.2.2 After the test, the performance of the sample should meet the requirements of 4.3.2. 4.10.3 Method
4.10.3.1 Place the sample on the test grounding plate, and the distance from the periphery to each side of the grounding plate should be not less than 100mm. 4.10.3.2 Adjust the output voltage of the electrostatic generator to 8000V, charge the electrostatic discharge probe connected to a 150pF capacitor and a 150Q resistor to 8000V, and discharge the sample through the 1500 resistor. After each charge, the electrostatic discharge probe should be immediately touched to a test point outside the sample. Regardless of whether arc discharge occurs, the tip of the probe must be in contact with the test point. Electrostatic discharge should be performed point by point at 10 different points on the outer surface of the sample (including the control mechanism or keyboard, the input/output line 150mm away from the sample, the farthest from the grounding line on the shell, the power switch, the display and indicator light, etc.), and the time interval between each discharge should be at least 1s. 4.10.3.3 During the test, monitor whether the sample sends out alarms and irreversible fault signals; after the test, perform basic functional tests on the sample in accordance with the provisions of Article 4.3.
4.10.4 Test equipment
4.10.4.1 Electrostatic generator: output voltage 8000V ± 800V, its electrical schematic diagram is shown in Figure 6, and the output current waveform is shown in Figure 7. Reh
Figure 6 Electrostatic generator electrical schematic diagram
5ns±30%
30ns±30%
Figure 7 Electrostatic generator output current waveform
. Discharge probe
Safety ground wire
4.10.4.2 Electrostatic discharge probe: The discharge end is an 8-ball, and the connector and the rear hemisphere are covered with insulating material. 4.10.4.3 Grounding wire: The grounding wire of the DC power supply and the electrostatic discharge probe used in the electrostatic discharge test must be connected to the safety grounding wire or the grounding plate together with the grounding plate.
4.11 Radiated electromagnetic field test
4.11.1
GB 17429-1998
Test the adaptability of the fire display panel to work in the radiated electromagnetic field environment. 4.11.2 Requirements
4.11.2.1 During the test, the sample should not issue a fire alarm and an irreversible fault signal. 4.11.2.2 After the test, the performance of the sample should meet the requirements of 4.3.2. 4.11.3 Method
4.11.3.1 Place the sample on the insulating table and connect the sample to the fire alarm controller according to the requirements of the normal monitoring state. Turn on the power supply to put the sample in the normal monitoring state.
4.11.3.2 Connect the test equipment according to Figure 8, place the transmitting antenna in the middle, and place the sample and the electromagnetic interference meter 1m on both sides of the transmitting antenna.
4.11.3.3 Adjust the output of the 1MHz~1GHz power signal generator so that the reading of the electromagnetic interference meter is 10V/m. During the test, the frequency should change slowly at a rate not greater than 0.005 octave/s within the frequency range of 1MHz~1GHz. At the same time, the sample should be rotated, and the working conditions of the sample should be observed and recorded. If the transmitting antenna used is directional, the transmitting antenna should be aligned with the electromagnetic interference meter antenna first, and the output of the power signal generator should be adjusted to 10V/m; then the transmitting antenna position should be reversed and aligned with the sample for testing. Within the frequency range of 1MHz~1GHz, the test should be carried out with the horizontal polarization and vertical polarization of the antenna respectively. 4.11.3.4 During the test, monitor whether the sample sends out alarms and irreversible fault signals; after the test, the basic function test of the sample should be carried out according to the provisions of Article 4.3.
4.11.3.5 The test should be carried out in a shielded room. To avoid large measurement errors, the position of the antenna should meet the requirements of Figure 9.
Electromagnetic interference measuring instrument
Transmitting antenna
Power signal generator
Test equipment layout
Test sample 1
Power signal generator antenna
Electromagnetic interference measuring instrument antenna
Obstacle or inner wall of shielded room
Figure 9 Antenna position diagram
4.11.4 Test equipment
4.11.4.1 Power signal generator (or signal generator and power amplifier) ​​a) Frequency range; 1 MHz ~ 1 GHz;
b) Output power: It should be able to provide sufficient power to meet the requirement of generating a 10V/m electromagnetic field 1m away from the transmitting antenna. The output power is 5063 Grounding wire: The grounding wire of the DC power supply and the electrostatic discharge probe used in the electrostatic discharge test must be connected to the safety grounding wire or the grounding plate together with the grounding plate.
4.11 Radiated electromagnetic field test
4.11.1
GB 17429-1998
Test the adaptability of the fire display panel to work in the radiated electromagnetic field environment. 4.11.2 Requirements
4.11.2.1 During the test, the sample should not issue a fire alarm and an irreversible fault signal. 4.11.2.2 After the test, the performance of the sample should meet the requirements of Article 4.3.2. 4.11.3 Method
4.11.3.1 Place the sample on the insulating table and connect the sample to the fire alarm controller according to the requirements of the normal monitoring state. Turn on the power supply to put the sample in the normal monitoring state.
4.11.3.2 Connect the test equipment according to Figure 8, place the transmitting antenna in the middle, and place the sample and the electromagnetic interference meter 1m on both sides of the transmitting antenna.
4.11.3.3 Adjust the output of the 1MHz~1GHz power signal generator so that the reading of the electromagnetic interference meter is 10V/m. During the test, the frequency should change slowly at a rate not greater than 0.005 octave/s within the frequency range of 1MHz~1GHz. At the same time, the sample should be rotated, and the working conditions of the sample should be observed and recorded. If the transmitting antenna used is directional, the transmitting antenna should be aligned with the electromagnetic interference meter antenna first, and the output of the power signal generator should be adjusted to 10V/m; then the transmitting antenna position should be reversed and aligned with the sample for testing. Within the frequency range of 1MHz~1GHz, the test should be carried out with the horizontal polarization and vertical polarization of the antenna respectively. 4.11.3.4 During the test, monitor whether the sample sends out alarms and irreversible fault signals; after the test, the basic function test of the sample should be carried out according to the provisions of Article 4.3.
4.11.3.5 The test should be carried out in a shielded room. To avoid large measurement errors, the position of the antenna should meet the requirements of Figure 9.
Electromagnetic interference measuring instrument
Transmitting antenna
Power signal generator
Test equipment layout
Test sample 1
Power signal generator antenna
Electromagnetic interference measuring instrument antenna
Obstacle or inner wall of shielded room
Figure 9 Antenna position diagram
4.11.4 Test equipment
4.11.4.1 Power signal generator (or signal generator and power amplifier) ​​a) Frequency range; 1 MHz ~ 1 GHz;
b) Output power: It should be able to provide sufficient power to meet the requirement of generating a 10V/m electromagnetic field 1m away from the transmitting antenna. The output power is 5063 Grounding wire: The grounding wire of the DC power supply and the electrostatic discharge probe used in the electrostatic discharge test must be connected to the safety grounding wire or the grounding plate together with the grounding plate.
4.11 Radiated electromagnetic field test
4.11.1
GB 17429-1998
Test the adaptability of the fire display panel to work in the radiated electromagnetic field environment. 4.11.2 Requirements
4.11.2.1 During the test, the sample should not issue a fire alarm and an irreversible fault signal. 4.11.2.2 After the test, the performance of the sample should meet the requirements of Article 4.3.2. 4.11.3 Method
4.11.3.1 Place the sample on the insulating table and connect the sample to the fire alarm controller according to the requirements of the normal monitoring state. Turn on the power supply to put the sample in the normal monitoring state.
4.11.3.2 Connect the test equipment according to Figure 8, place the transmitting antenna in the middle, and place the sample and the electromagnetic interference meter 1m on both sides of the transmitting antenna.
4.11.3.3 Adjust the output of the 1MHz~1GHz power signal generator so that the reading of the electromagnetic interference meter is 10V/m. During the test, the frequency should change slowly at a rate not greater than 0.005 octave/s within the frequency range of 1MHz~1GHz. At the same time, the sample should be rotated, and the working conditions of the sample should be observed and recorded. If the transmitting antenna used is directional, the transmitting antenna should be aligned with the electromagnetic interference meter antenna first, and the output of the power signal generator should be adjusted to 10V/m; then the transmitting antenna position should be reversed and aligned with the sample for testing. Within the frequency range of 1MHz~1GHz, the test should be carried out with the horizontal polarization and vertical polarization of the antenna respectively. 4.11.3.4 During the test, monitor whether the sample sends out alarms and irreversible fault signals; after the test, the basic function test of the sample should be carried out according to the provisions of Article 4.3.
4.11.3.5 The test should be carried out in a shielded room. To avoid large measurement errors, the position of the antenna should meet the requirements of Figure 9.
Electromagnetic interference measuring instrument
Transmitting antenna
Power signal generator
Test equipment layout
Test sample 1
Power signal generator antenna
Electromagnetic interference measuring instrument antennaWww.bzxZ.net
Obstacle or inner wall of shielded room
Figure 9 Antenna position diagram
4.11.4 Test equipment
4.11.4.1 Power signal generator (or signal generator and power amplifier) ​​a) Frequency range; 1 MHz ~ 1 GHz;
b) Output power: It should be able to provide sufficient power to meet the requirement of generating a 10V/m electromagnetic field 1m away from the transmitting antenna. The output power is 506
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.