Some standard content:
Chemical Industry Standard of the People's Republic of China
HG2182-91
Issued on December 23, 1991
Implemented on May 1, 1992
Ministry of Chemical Industry of the People's Republic of China
Chemical Industry Standard of the People's Republic of China
Subject content and applicable scope
HG 2182-91
This standard specifies the technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of cotton-rubber shoes. This standard is mainly applicable to general cotton-rubber shoes with rubber as base material and cold-proof and warm-keeping materials as upper materials, which are processed by gluing and hot vulcanization process. It is not suitable for cotton-rubber shoes with enzyme acid resistance, domain resistance, oil resistance, insulation and other special purposes. 2 Reference standards wwW.bzxz.Net
GB528 Determination of tensile properties of vulcanized rubber
GB531 Test method for rubber Shore A hardness CB532 Determination of adhesion strength between vulcanized rubber and fabric GB1682 Test method for brittle temperature of vulcanized rubber GB1689 Determination of wear resistance of vulcanized rubber (using Akron abrasion machine) GB/T2941 Standard temperature, humidity and time for environmental conditioning and testing of rubber specimens GB3293 Chinese shoe size and shoe size series
HG/T2198 General requirements for physical test methods for vulcanized rubber 3 Technical requirements
3.1 The shoe size, model, shoe size and shoe size classification of shoes shall be implemented in accordance with the provisions of G3293. 3.2 The physical and mechanical properties shall conform to the requirements of Table 1. Inspection parts: Stripe and upper
Tensile strength, MPa
Tear elongation at break, %
Maximum loss, cm3
Hardness, A
Brittle temperature,
Viscous strength, kN/m
When the width of the stripe does not meet the test requirements, it will not be included in the assessment. When the outer sole formula or pattern is changed, the winning temperature will be included in the assessment. 3.3 The appearance quality shall conform to the requirements of Table 2.
Ministry of Chemical Industry of the People's Republic of China approved the project on December 23, 1991
1992-05-01 implementation
Part
Inner diameter
"Strips"
Big stems"
A pair of shoes color difference
Mouse yarn, skipped yarn
1 Slightly regulated
First-class products
HG 2182 -- 91
1 111 Regulated, regulated ... mm or less, limited to one place
not allowed
, the second place
does not leak
the inner sole cloth, the shoe stone is not dangerous, the door strip is less than 3mm long, the shoe cloth is not only, the mouth strip is less than 6mm long, the edge strip, the inner sole
cloth, the shoe cloth is not cracked!
, after repair, limited to one place
not more than 5mm
basically even and does not affect the appearance
stitching line. Gradually no one shall have
hard particles, prohibited objects,
medical and military
toe size
sticky thin traces
curling, beating
height difference of the surrounding strips
the cumulative area shall not exceed 500 square meters
basic flat wall
diameter shall not exceed 1 meter, height shall not exceed 0.5 mm, limited to one place, no one shall have it at the bend (needle clothing is not included in this limit), depth shall not exceed 1nm, limited to one place, no one shall have it at the bend, the length of the upper seam shall not exceed 3 pulls
the area shall not exceed 10mm
the difference in the shoe cannot exceed 5 square meters
the area shall not exceed 50mm, limited to one place, the basic pattern shall be clear, the toe and the round strip bend shall not have it, and the curling length of other parts shall not exceed 5 mm Limited to one place, the skirt is not allowed to have both the inner stripe 2-5m, the outer stripe is basically parallel and neat 7mm
The lowering of the back color
does not exceed mm
does not significantly affect the appearance
The clear development of the Tao Xiaoqi
The cumulative area is not less than 700m
No color difference
The straight inspection does not exceed 2m. The height and unevenness are limited to 0.5mm, the bend is not allowed (the needle limit is not included in this limit), the depth does not exceed 2m, the concave part is not allowed, the length of the upper joint does not exceed E
The area does not exceed 20rm2
The difference between a pair of shoes does not exceed 8 mm
The area shall not exceed 100mm, and the limit shall not have any strange places such as the head cover and the inverted strips. The curling length of other parts shall not exceed 10mm, and the skirt shall not be shorter than 5mm. Only one place shall exceed the first-class product regulations and shall not obviously affect the appearance. ~9mm
The unevenness and air area shall not exceed 200mm, and the height shall not exceed 2mm three! The area does not exceed 400mm, the height does not exceed 2mm, and the limit is three bubbles. Sand particles, debris, diameter, height and depth do not exceed 2mm, and the limit is two places. The sound does not exceed 4mm in diameter, and the height and depth do not exceed 2 mm, and the limit is two. There are filters, and there are no bends. There are no com parts. Fittings. There are air holes on the cutting edge. There are traces of adhesion and movement. First-class products. Check pants. No more than 2mm, and limited to three places. Table 2. Qualified products. The diameter does not exceed 3 mm. The length shall not exceed 5mm and the depth shall not exceed 2mm. The length of the bend shall not exceed 10mm and the depth shall not exceed 2.mm. There shall be no accumulation of bacteria at the bend and the area shall not exceed 300m. In this group, there shall be no more than two places. The cumulative area shall not exceed 1000mm, and the flat area shall not exceed 400mm. There shall be no more than one place. The basic groove area of the pattern shall not exceed the addition. There shall be no more than one place. The basic pattern area shall not exceed 7mm for a pair of shoes above No. 20 and no more than 4 mm for No. 19/2. There shall be no more than 14mm for a pair of shoes above No. 20 and no more than 8mm for No. 19/2. There shall be no more than 14mm for a pair of shoes above No. 20 and no more than 8mm for No. 19/2. It should be handled according to the items in the table. Appearance defects that seriously affect the appearance or wear should not be considered as qualified products. 4 Physical and mechanical properties test methods
4.1 The physical and mechanical properties test methods of rubber shall be carried out in accordance with HG, T21. The finished product test pieces can be cut along the direction of the outsole. 4.2 Rubber test conditions shall be carried out in accordance with GB/T2941. The sample placement time before the test should not be less than 6 hours. 4.3 The determination of rubber tensile properties shall be carried out in accordance with GB528. The outsole performance test adopts 6EL cutting force. 4.4 Rubber liquid Shore A hardness test shall be carried out in accordance with GB 531. 45 The determination of rubber penetration resistance shall be carried out in accordance with GB1689. When the test piece is not long enough, it can be overlapped along the outsole. When the outsole thickness is thin, the wear test piece can be 2~3mm.
46 The determination of the adhesive strength between the circumference and the shoelace shall be carried out in accordance with GB532. The cutting of the sample: one test piece is taken on each side of the shoe. The effective width is 10.0±0.2mm, the length is 100～150mm, and the pattern agent is extended to 40～50mm (i.e. the effective length of the test piece) along the effective width of the outer fixing strip. Use a small blade to align the cloth and the glue at the effective width of one end of the test piece. 4.7 Rubber brittle temperature test shall be carried out in accordance with GB1682 5 Inspection rules
51 Appearance inspection is based on visual inspection, and each pair shall be inspected. Quality problems that cannot be shown by a single pair shall be inspected in pairs when matching. Appearance quality shall be graded according to Table 2.
52 Physical and mechanical properties inspection shall be based on the output of every 1 to 3 days as a batch (the maximum batch shall not exceed 20,000 pairs). One pair can be randomly selected from each batch for inspection. If it fails to meet the requirements for the first time, double sampling shall be conducted for testing, and the unqualified items shall be retested. The retest results shall be determined by the lowest performance data of the additional test shoes to determine whether the batch of products is qualified. Hidden temperature is not listed as a batch inspection item. 6 Marking, packaging, transportation, purchase and storage
61 Each shoe shall have the following marks:
a. Manufacturer's name;
h Shoe size and model;
e Trademark or brand name;
d Product grade:
e Year and month of production.
HG 2182-91
62 Each pair of shoes should be packed in paper bags, plastic bags or paper boxes, and the following signs should be on the surface: Manufacturer's name;
b Product name:
C Shoe size and model:
d Trademark or brand name;
e Product grade;
f Precautions for wearing.
63 The outer packaging should be cardboard boxes, the seal should be firm, the box should be tied tightly, and the box surface should have the following labels: manufacturer name;
product name;
product standard number or batch number;
d, product specifications, quantity;
trademark or trademark name;
product grade;
production year and month;
h total weight;
size and volume,
64 When transporting shoes, they must be covered, and it is strictly forbidden to put them together with oil, acid, alkali or other corrosive substances. 65 When storing shoes, they should be placed in a properly dry and ventilated room, more than 20cm away from the ground and walls, away from moisture, heat sources and direct sunlight. It is strictly forbidden to place them in the open air and be affected by oil, acid, alkali or other corrosive substances. 66 Shoes are transported and stored under the above conditions and in the original packaging of the manufacturer. Within one year from the date of production, the manufacturer shall ensure that the rubber parts are not sprayed with sulfur. During storage, the stacks shall be checked every three months. Additional notes:
This standard was proposed by the Science and Technology Department of the Ministry of Chemical Industry of the People's Republic of China. This standard is under the jurisdiction of the Shanghai Rubber Shoes Research Institute. This standard was drafted by Harbin Rubber Factory. The main drafters of this standard are Tang Daocheng and Chen Jian.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.