title>SY/T 5203-1991 General principles for basic environmental testing of petroleum exploration and development instruments - SY/T 5203-1991 - Chinese standardNet - bzxz.net
Home > SY > SY/T 5203-1991 General principles for basic environmental testing of petroleum exploration and development instruments
SY/T 5203-1991 General principles for basic environmental testing of petroleum exploration and development instruments
Basic Information
Standard ID:
SY/T 5203-1991
Standard Name: General principles for basic environmental testing of petroleum exploration and development instruments
SY/T 5203-1991 General Principles of Basic Environmental Tests for Petroleum Exploration and Development InstrumentsSY/T5203-1991 Standard download decompression password: www.bzxz.net
Some standard content:
Petroleum and Natural Gas Industry Standard of the People's Republic of China SY/T 5203—91 Basic Environmental Tests for Petroleum Exploration and Development Instruments Published on January 15, 1992 Ministry of Energy of the People's Republic of China Implementation on July 1, 1992 1 Subject Content and Scope of Application Petroleum and Natural Gas Industry Standard of the People's Republic of China Basic Environmental Tests for Petroleum Exploration and Development Instruments SY/T 5203---91 Replaces SY 5203—87 This standard specifies the environmental condition grouping of petroleum exploration and development instruments (hereinafter referred to as instruments), specifies the environmental test items that should be carried out in the development, finalization and production stages of the instruments, and makes unified provisions for the common requirements of various tests. This standard applies to the environmental tests of instruments. 2 Reference Standards GB6587.1 General Principles of Environmental Test for Electronic Measuring Instruments 3 Environmental Grouping Petroleum exploration and development instruments can be divided into two categories according to environmental conditions. The first category is various measuring and recording instruments used on the ground, and the second category is instruments or probes used for in-well measurements. These two types of instruments can be divided into six groups due to different transportation and use conditions. 3.1 Class I environment is divided into three groups according to the working conditions of ground instruments: a. Group A has a good working environment, that is, an air-conditioned environment that can automatically adjust the ambient temperature, including the internal environment of a van-type instrument vehicle with air-conditioning equipment; b. Group B is a general laboratory and the internal environment of a van-type instrument vehicle; c. Group C is a natural environment in the field. 3.2 Class II environment is divided into three groups according to the depth of the well used by the downhole instruments: d. Group D is used for downhole instruments within 2000m; e. Group E f. Group F is used for downhole instruments above 5000m. 3.3 Environmental test technical conditions grouping (see Table 1). 4 Environmental test items 4.1 Test item content: a. High temperature test b. Impact test c. Salt spray test, d. Low temperature test e: Steady humidity test: f, Free fall test, 9. Vibration (sinusoidal) test Approved by the Ministry of Energy of the People's Republic of China on January 15, 1992, and implemented on July 1, 1992 SY/T5203-91 -2s/g*6 ZHS~002~9 23/086 ZH9--0~s 2H9~001~9 zH9~001~9 es/wg'6t 2115~999 901~98 su t年 -s/ug'61 ZHS~99~9 .911%(065) .09%(S02).00 H%(9808) H%(96~06) %(98~08)(9606).02 .002+-:02 - 0.991+~07 - 0.02 +~0 0.01+~0 - 0,02+~0f - 0.s9+-01- 0.02+~0# - 0.09+~03- 函许癌 h.Pressure testwww.bzxz.net i, tilting and overturning test i. Dense tree test k, high temperature and high pressure test: 1. Humidity/pressure comprehensive test; m, temperature/vibration comprehensive test: n. Broadband random vibration test. SY/T 5203—91 4.2 The environmental test items that should be carried out at each stage of prototype development, product finalization and product acceptance are as follows (see Table 2). 5 Test procedures The steps and requirements for each test are specified by the method standards of each sub-test. The method standards of each sub-test should include the following procedures and contents: a, pretreatment (if necessary) b, initial inspection: c, conditional test (if necessary, the intermediate inspection during the test should be specified) 1d. Recovery . Final (final) inspection. Table 2 Environmental test items at each stage Engineering stage Special Necessity Test method High temperature test Impact test Salt spray test Injury test Stationary test Free fall test Vibration (sinusoidal) test Pressure test Tilt overturn test Sealing test High temperature and high pressure test Temperature/pressure comprehensive test Temperature/vibration comprehensive test Broadband random vibration test Prototype development Note: - Necessary, ○ - Optional and sampled. 5.2 Test report 5.2.1 Test reports should be prepared for each test. 5.2.2 The test report shall include the following contents:0 a: Test item name and test period (year, month, day): b. Test equipment, c. Test technical indicators and requirements, d. Brief test process# Product finalization Product acceptance e. Test results: f. Test and inspection personnel (signature). SY/T 5203-9F 5.2.3 The format of the test report shall be compiled and printed by the responsible test unit. 6.1 Ambient temperature: 20±2°C; 6.2 Ambient humidity: 15%~75%RH 6.3 Gas pressure: 86106kPa# 6.4 AC power supply: voltage 220±4.4V (or voltage specified by instrument standard), frequency 50±0.5Hz (or frequency specified by instrument standard) 36.5 DC power supply: ±1% of value specified by instrument standard! 6.6 External electromagnetic field interference: avoid 6.7 Working position: controlled by instrument standard. 7 Relevant instructions 7.1 If the environmental conditions specified by instrument standard are inconsistent with the environmental conditions of this standard, as long as the conditions specified by instrument standard are more stringent than those specified by this standard, the standards specified by the instrument shall be followed. 7.2 Special instruments, if there are special conditions, may not be restricted by the provisions of this standard, but shall be in accordance with relevant professional or national standards. .3 Any other test methods not included in this standard can be carried out in accordance with the corresponding professional or national standards. If necessary, enterprises can compile the required enterprise standard test methods by themselves. Additional remarks: This standard is proposed and managed by the Petroleum Exploration Instrument Professional Standardization Committee. This standard was revised by the Anhui Oil Exploration Instrument Factory in August 1991. The drafter of this standard revision is Xu Huasheng. This standard is still valid after the review in 199 , and the review result has been approved by the State Administration of Petroleum and Chemical Industry. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.