Some standard content:
ICS01.080.10
National Standard of the People's Republic of China
GB/T18302--2001
Basic requirements for instruments to fly the National Flag2001-01-21Promulgated
Implemented on 2001-05-01
Promulgated by the State Administration of Quality and Technical Supervision
People's Republic of China
National Standard
Basic requirements for instruments to fly the National Flag
GB/T18302—2001
Published by China Standards Press
No. 16, Sanlihe North Street, Fuxingmenwai, Beijing
Postal Code: 100045
Tel: 6852394668517548
Printed by Qinhuangdao Printing Factory of China Standards PressSold by Xinhua Bookstores in Ningxia
Published by Beijing Xinhua Bookstore
Book size 880X12301/16 Printing sheet 1/2 Word count 8,000 words First edition April 2001 First printing April 2001 Print run 1-1500
Book number: 1550661-17520
Website bzcbs.com
Subject 565-439
Copyright exclusive Infringement must be investigated
Report phone: 010)68533533
GB/T18302—2001
This standard is formulated to maintain the dignity of the national flag and the image of the country. The formulation of this standard is conducive to the in-depth implementation of the "National Flag Law of the People's Republic of China" and the implementation of GB12982-1996 "National Flag", and is conducive to standardizing the raising, hanging and use of the national flag by various domestic units and individuals. This standard is proposed and managed by the National Technical Committee on Color Standardization. The responsible drafting units of this standard are: Institute of Psychology, Chinese Academy of Sciences, Beijing Institute of Fashion Technology, Sichuan Tianfu General Flagpole Products Co., Ltd. The main drafters of this standard are: Sun Xiuru, Han Buxin, Zhan Binghong, Liu Shifu, Wang Lin. This standard was first issued in January 2001.
1 Scope
National Standard of the People's Republic of China
Basic requirements for instruments to fly the National Flag
Basic requirements for instruments to fly the National Flag This standard specifies the technical requirements, markings, labels and packaging for instruments to fly the National Flag. GB/T18302-2001
This standard applies to national flag hoisting devices made of metal, metal-plastic composite materials, glass fiber reinforced plastics and natural materials such as bamboo and wood. Other flag hoisting devices can also be implemented by reference. 2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. The versions shown are valid when this standard is published. All standards are subject to revision, and parties using this standard should explore the possibility of using the latest versions of the following standards. 88J9 General Atlas of Outdoor Engineering Building Structures. 3 Definitions
This standard adopts the following definitions.
3.1 Instruments for flying flag The supporting equipment and facilities required for raising and hanging flags, including flagpoles, flag crowns, flag stands and other auxiliary devices. 3.2 Single-story building single floor building A building with only one floor on the ground.
3.3 Multi-story building multi floor building A building with more than two floors on the ground.
3.4 Square flag flag flying on a square A flag hoisted in front of a square or building. 3.5 Building exterior wall flag flag flying on a wall A flag hoisted at a certain part of the exterior wall of a building and at a certain angle to the wall of the building. 3.6 Building top flag flag flying on a building A flag hoisted on the top of a building.
3.7 Door flag flagflyingonadoorcase A flag erected at the main entrance of a building.
3.8 Marching flag flagflyinginaprocession A flag held in a procession.
3.9 Indoor flag flagflyingindoor A flag erected and hung on the floor of an office, conference room, or hall. 3.10 Table flag flagflyingonatable
A flag placed on a table, including a single-pole single flag and a single-pole double-wing flag (also known as a signing flag). 3.11 Interval between flagstaffs Approved by the State Administration of Quality Supervision, Inspection and Quarantine on January 21, 2001, implemented on May 1, 2001
GB/T18302—2001
When more than two flagpoles are erected in front of a square or building, the distance between the flagpoles. 3.12 Height of the base of a flagstaff The vertical distance from the ground to the flagstaff on the outer wall of the building. 3.13 Angle between flagstaff and a wall The angle between the flagstaff on the outer wall of the building and the wall of the building. 3.14 Cap of the flagstaff
The decoration on the top of the flagpole, generally in a spherical shape. 4 Requirements
4.1 Materials for the hoisting device
4.1.1 Metal, metal-plastic composite material, glass fiber reinforced plastic, bamboo and wood natural materials can be used to make the hoisting device (except for the square flag stand).
4.1.2 The physical properties of the material of the square flagpole should take into account the design strength, safety factor, bending stress, corrosion resistance, weather resistance, etc. It should be able to ensure that the flagpole will not fall, bend or fold under the geographical location and environmental climatic conditions of the location where the flagpole is set. 4.2 Color of the flag hoisting device
4.2.1 The colors specified in this standard are named by common names. 4.2.2 In the flag hoisting device, the outdoor flag pole should be silvery white, white or wood color, and the indoor flag pole should be silvery white, golden yellow, wood color, and gray series.
4.2.3 The color of the square flag holder must be harmonious with the color of other parts of the flag hoisting device. 4.3 Appearance of the flag hoisting device
4.3.1 Flag poles of various materials must be surface treated to achieve a straight, smooth and unstained appearance. 4.3.2 The rope and pulley equipped with the square flag pole should be suitable for the flag hoisting pole in terms of strength and color. The technical requirements for the use of bearing pulleys refer to the 88J9 "General Atlas of Outdoor Engineering Building Structures". 4.3.3 Other materials whose physical properties and appearance requirements meet or exceed the requirements specified in 4.1.2, 4.2.2, 4.3.1.4.3.2 can also be used to make national flag hoisting devices.
4.4 Shape and size of flag hoisting device
4.4.1 The cross section of the flag pole of the flag hoisting device in this standard should be circular, and the flag crown is generally spherical. 4.4.2 Size of outdoor flag hoisting device
4.4.2.1 The height of the flag pole in the square should be 5m~7m in front of a single-story building, and 7m~15m in front of a multi-story building. 4.4.2.2 The height of the flag pole, flag pole diameter, flag crown diameter, flag pole spacing and flag size of the flag hoisted in the square are shown in Table 1. mm
Table 1 Flagpole distance, flagpole diameter, flag crown diameter, flagpole spacing and flag size Configuration No.
Flagpole height 1
5000≤H<7000
7000≤H<9000
9000≤H<12000
12000≤H<15000
Flagpole diameter||t t||108 connected to 89
114 connected to 101
133 connected to 114 connected to 101
159 connected to 133 connected to 114
Flag crown diameter
160~195
180~220
180~220
200~250
Flag pole spacing
>2 000
Flag size
1440×960
1920×1280
2400×1600
2880X1920
4.4.2.3 The technical parameters of the square flag stand refer to the "Flagpole" section in 88J9 "General Atlas of Outdoor Engineering Building Structures". 4.4.2.4 Flagpole height, flagpole diameter, flag crown diameter, flag socket height, flag stand angle and flag size configuration on the exterior wall of the building are shown in Table 2.
Flagpole height
GB/T18302—2001
Flagpole height, flagpole diameter, flag crown diameter, Table 2
Flag socket height, flag stand angle and flag size configuration on the exterior wall of the building Flagpole diameter
Flag crown diameter
Flag socket height
≥1800
≥2500
Flag stand angle
42°±3°
42°±3°
42°±3°
4.4.2.5 Flagpole height, flagpole diameter, flag crown diameter and flag size configuration on the top of the building are shown in Table 3. Table 3 for the configuration of flagpole height, flagpole diameter, flag crown diameter and flag size at the top of buildings
Building category
Three floors and above
Flagpole height
3000≤H5000
5000≤H<6000
6000≤H<8000
Flagpole diameter
114 connected to 101
Flag crown diameter
160195
190~220
190~220
The configuration of the flagpole height, flagpole diameter, flag crown diameter and flag size of the marching flag is shown in Table 4. Table 4 Flagpole height, flagpole diameter, flag crown diameter and flag size configuration for marching flag Flagpole height
3 Indoor flag hoisting device size
Flag stick diameter
Flag crown diameter
4.4.3.1 The flagpole height, flagpole diameter, flag crown diameter and flag size configuration for vertical flag are shown in Table 5. Table 5 Flagpole height, flagpole diameter, flag crown diameter and flag size for vertical flags Building indoor floor height
Below 3000
3000~4000
Above 4000
Flagpole height
2200~2400
2500~3000
Not less than 3000
Flagpole diameter
Flag crown diameter
Not less than 70
Flag size
960X640
1440×960
1440×960 or
1920X1280
|Flag size
1440×960
1920×1280
2400X1600
Flag size
960X640
1440×960
1920×1280
2400×1600
2880X1920
Flag size
1440×960
1920X1280
2400×1600
See Table 6 for the flagpole height, flagpole diameter, wing length, wing diameter, flag crown diameter and flag size configuration of the table flag. Table flagpole height, flagpole diameter, wing length, wing diameter, flag crown diameter and flag size configuration table 6
Flagstand type
Single pole single flag
Single pole double wing flag
Flagpole commercial degree
270±5
350±5
300±5
1) Wing length does not include wing flag crown
Flagpole diameter
Wing length degrees\”
140~150
Wing diameter
Flag crown diameter
Flag size
150×100
210×140
210×140
GB/T183022001
4.4.3.3 The wings of a single-pole double-wing flag should be symmetrical relative to the vertical pole. The angle between the two wings should be 110°~ It is advisable to be within the range of 120°, see Figure 1. 110°~120
Figure 1 The angle between the wing and the vertical pole in the single-pole double-wing flag 5 Marking, labeling and packaging
5.1 Each set of equipment should be marked with the product name, material, specification, color, manufacturer name and address, product standard abbreviation, product certificate, and trademark.
5.2 Each set of lifting device must be packaged separately. The packaging must ensure that the quality of the lifting device is not damaged and is convenient for transportation and storage. The product name, specification, material, packaging size, quantity, weight, manufacturer name and address, trademark and national standard number, and transportation mark should be indicated on the outside of the outer packaging. The necessary accessories for installation and use, installation and storage instructions and inspection certificate should be included in the package. Copyright is exclusive and infringement must be investigated
Book number: 155066·1-17520
Subject 565-4391 Each set of equipment should be marked with the product name, material, specification, color, manufacturer name and address, product standard abbreviation, product certificate, and trademark.
5.2 Each set of lifting device must be packaged separately. The packaging must ensure that the quality of the lifting device is not damaged and is convenient for transportation and storage. The product name, specification, material, packaging size, quantity, weight, manufacturer name and address, trademark and national standard number, and transportation mark should be indicated on the outside of the outer packaging. The necessary accessories for installation and use, installation and storage instructions, and inspection certificate should be included in the package. Copyright exclusive infringement must be investigated
Book number: 155066·1-17520bzxz.net
Subject 565-4391 Each set of equipment should be marked with the product name, material, specification, color, manufacturer name and address, product standard abbreviation, product certificate, and trademark.
5.2 Each set of lifting device must be packaged separately. The packaging must ensure that the quality of the lifting device is not damaged and is convenient for transportation and storage. The product name, specification, material, packaging size, quantity, weight, manufacturer name and address, trademark and national standard number, and transportation mark should be indicated on the outside of the outer packaging. The necessary accessories for installation and use, installation and storage instructions, and inspection certificate should be included in the package. Copyright exclusive infringement must be investigated
Book number: 155066·1-17520
Subject 565-439
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.