GB/T 325.3-2010 Packaging container steel drums Minimum total capacity 212L, 216.5L and 230L closed steel drums GB/T325.3-2010 |tt||Standard download decompression password: www.bzxz.net
This part specifies the structure and dimensions of minimum capacity fully closed steel drums.
GB/T325 "Packaging Container Steel Drums" is divided into 5 parts:
———Part 1: General technical requirements;
———Part 2: Fully open steel drums with a minimum total capacity of 208L, 210L and 216.5L;
———Part 3: Closed steel drums with a minimum total capacity of 212L, 216.5L and 230L;
———Part 4: Fully open steel drums of 200L and below;
———Part 5: Closed steel drums of 200L and below.
This part is Part 3 of GB/T325.
This part is consistent with ISO15750-2:2002 "Packaging steel drums Part 2: Closed steel drums with minimum total capacity of 212L, 216.5L and 230L
" (English version) in the modified adoption. The main differences are as follows:
———According to the actual domestic situation, the terms and definitions adopt the provisions of GB/T4122.4, the steel drum materials comply with
the provisions of GB/T325.1 , and the closure materials comply with the provisions of GB/T13251;
———Deleted the process content; ||tt
|| ———Deleted the requirements for the emptying rate of steel drums;
———Deleted the provisions on the representation of specifications and models of closed steel drums;
———Deleted Appendix A, Measurement method of closed steel drum capacity;
———Deleted Appendix B, Test method of closed steel drum emptying rate.
This part is proposed and managed by the National Technical Committee for Packaging Standardization.
The drafting units of this part are: National Packaging Product Quality Supervision and Inspection Center (Guangzhou), Hangzhou COFCO Packaging Co., Ltd., Wuxi Sifang Barrel Co., Ltd.
The main drafters of this part are: Cai Yijun, Lu Ming, Ling Guangyao, Zhu Liping, Ju Chunming, Zhang Xiaoshang, Guo Kewen, Wang Xiaoru, Luo Xiaoyin, Yao Xiaoqing, Zhao Jizhen, Huang Guangchi.
The clauses in the following documents become the clauses of this part through reference in this part of GB/T 325. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this part. However, the parties to the agreement based on this part are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this part.
GB/T325.1 Packaging container steel drums Part 1: General technical requirements
GB/T4122.4 Packaging terms Part 4: Materials and containers
GB/T13251 Packaging steel drums with embedded flange closures (GB/T13251—2008, ISO15750-3:2002, NEQ)

ICS 55. 140
National Standard of the People's Republic of China
GB/T325.3—2010
Packaging container
Part 3: Closed-end steel drums with a minimum total capacity of 212 L, 216.5 L and 230 L
Packaging container--Steel drums-Part 3: Non-removable head (tight head) drums with a minimum total capacity of 212 L, 216.5 L and 230 L(ISQ 15750-2:2002,Packaging—Steel drums-Part 2:Non-removable head (tight head) drums with a minimum total capacity of 212 L, 216.5 L and 230 L, MOD) 2010-09-26 release
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
Jinban.com
2011-03-01 implementation
GB/I325 "Packaging Container Steel Drum" is divided into 5 parts: Part 1: General technical requirements;
Part 2: Minimum total capacity 208L, 210L and 216.51. umbrella-shaped steel drums; Part 3: Minimum total capacity 2121216.51. and 230L closed steel drums: Part 4: 200L and below fully open steel drums; Part 5: 2001. and below closed steel drums. This part is Part 3 of GB/T325.
GB/T 325.3-~-2010
This part number is ISO15750-2:2002 "Packaging steel drums Part 2: Minimum total capacity 212I, 216.51. and 230L closed steel drums" (English version) The degree of consistency is modified and adopted. The main differences are as follows: According to the actual domestic situation, the terms and definitions are adopted (G13/T4122.4, the steel drum material conforms to the provisions of GB/T325.1, and the closure material conforms to the provisions of GB/I13251; the process content is deleted;
The requirements for the emptying rate of steel drums are deleted;
The provisions on the representation of the specifications of closed steel drums are excluded; In addition to the appendix, the measurement method of the capacity of closed steel drums: Appendix B, the test of the emptying rate of closed steel drums is deleted Method. This part was proposed by the National Packaging Standardization Technical Committee and is under the jurisdiction of the drafting units of this part: National Packaging Product Quality Supervision and Inspection Center (State), Hangzhou COFCO Packaging Co., Ltd., Guangxi Sifang System Co., Ltd.,
The main drafters of this part: Cai Yijun, Lu Ming, Ling Guangyao, Zhu Liping, Nan Chunming, Zhang Xiaoshang, Guo Kewen, Shi Xiaogu, Luo Xiaoyin, Yao Xiaoqing, Zhao Jizhen, Huang Guangchi.
Snow Product Partner Network ht:
1 ScopeWww.bzxZ.net
Packaging container steel drum
Part 3: Minimum total capacity 212L, 216.5I and 230L closed steel drum
GB/T325.3—2010
This part of GI3/T325 specifies the minimum total capacity of 212L, 216.5L and 2. Structure and dimensions of 230L closed steel drums. 2 Normative references
The clauses in the following documents become clauses of this part through reference in this part of GB/F325. For any referenced document with a punctuation date, all subsequent amendments (excluding errata) or revisions are not applicable to this part. However, parties that reach an agreement based on this part are encouraged to study whether the latest versions of these documents can be used. For any referenced document without a punctuation date, its latest version applies to this part.
CB/T325.1 Packaging container steel drums Part 1: General technical requirements GB/F4122.1 Packaging terms Part 4: Materials and containers GB/I13251 Packaging steel drums with embedded flange closures (GB/T13252008, ISO157 50-32002, NFQ) 3 Terms and definitions
The terms and definitions established in GB/T4122.4 apply to this part of GB/T325. 4 Specifications and dimensions
4.1 The dimensions of steel drums are shown in Figure 1. The specific dimensions of Type A, Type B and Type C drums are shown in Table 1. Snow product companion network htt
GB/T325.3—2010
The closure shall not be higher than the edge of the drum cover. Note: The drum cover can be flat, flat or concave. Dimensions
Outer diameter of the ring rib
Total capacity
Outer diameter of the rolled edge
Depth of the drum cover"
Figure 1 Closed steel drums
Table 1 Specifications and dimensions of closed steel drums
Type A drum
ht
571. 5—2
932±5
(i 3/4
13-type barrel
878±5
Unit is close meter
Unit is side meter
C-type box
571. 5±2
932±5
566三2
Bottom clearance
Ring rib spacing
Total capacity
Injection population center Food ventilation I center distance
Injection port G2 (50mm) center to the barrel outer connection distance, measured about 50mm from the top
Table 1 (continued)
A Jingqi
444: Upper 6
280—3
444±6
GB/T325.32010
Unit is Tanglai
B type barrel
(or 451+1) (or 4511) (or 451=1) (or 451+1)72+3
72 ±:3
According to GB/T13251, the insertion of the threaded G2 closure should make the center line as vertical as possible. Note 1: For steel drums with concave drum covers, in order to achieve the specified capacity, the overall height H1 of the drum can be increased by 4 mm7213
C-type drums
300±3
Note 2: Among the three types of steel, the best outer diameter of type A and type C should meet the standard container. One steel drum can be stacked side by side. a The depth of the drum cover meets the requirement that the closure is not higher than the curling edge. 4.2 The thickness of the steel plate is 0.6mm1.6mm.
5 Materials
5.1 The material of the steel drum meets the requirements of GB/T325.1. 5.2 The material of the closure meets the requirements of G13/T13251. 6 Structure
6.1 It should meet the requirements of GB/T 325. 1. 6.2 The barrel body, barrel cover and barrel bottom should be made of steel plates of sufficient thickness according to the purpose of the steel barrel. 6.3 The barrel body is strengthened by expanding or rolling two ring ribs, the positions of which are shown in Figure 1. Ring ribs and corrugations of different structures can also be used. 6.4 The shape of the barrel cover and barrel bottom can be convex, flat or concave. 6.5 The position of the closure on the barrel cover is shown in Figure 1. According to the agreement between the supplier and the buyer, one injection port or each injection port and vent port can be installed. 6.6 The thread of the closure shall comply with the provisions of the thread (3/4 and thread G2 in GI3/T13251. 6.7 Except as stipulated in the agreement between the supplier and the buyer, the structure of the closure shall comply with the provisions of GB/T13251. 6.8 Unless the closure itself has waterproof performance, it shall be equipped with a liner/gasket or other sealing element. 6.9 Metal or plastic barrel plugs shall be equipped with a liner/gasket of suitable material. http
GB/T 325. 3-2010
Print date: January 14, 2011 F047
ht
National Standard of the People's Republic of China
Packaging Container Steel Drum
Part 3; Minimum total capacity 212 L, 216. 5 L and 230L closed steel drum
CB/T 325, 3—2010
Published and distributed by China Standards Press
No. 16, Sandan Hebei Street, Fuxingmenwai, Beijing
Postal code: 100015
Website: www, spc. net, cn
Tel: 68523946
68517548
China Standards Press Qinhuangdao Printing Factory Printing Valley Xinhua Bookstore Distribution
Format: 880×1230 1/16 Printing Sheet: 0.55 Words: 8,000 Words
No.: -, 2010 November Edition: First Printing in November 2010*
No.: 155066·1-40653 Extended Price: 14.00 yuan If there is any printing error, the distribution center of our company will replace it. Copyright infringement will be investigated.
Report phone: (010)68533533
oodmatenet
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.