HG/T 2738-1995 Series and basic parameters of flat double enveloping toroidal worm reducers for tire shaping and vulcanizing machines HG/T2738-1995 Standard download decompression password: www.bzxz.net

Chemical Industry Standard of the People's Republic of China
HG/T2738--95
Series and basic parameters of plane secondary enveloping toroidal worm reducers for tire shaping and vulcanizing machines
1995-0705 Issued
Ministry of Chemical Industry of the People's Republic of China
Implementation of precision net change m.baonno.con199603-01
Chemical Industry Standard of the People's Republic of China
Series and basic parameters of plane secondary enveloping toroidal worm reducers for tire shaping and vulcanizing machines
Subject content and scope of application
IIG/T2738--95
This standard specifies the series and basic parameters of plane secondary enveloping toroidal worm reducers for tire shaping and vulcanizing machines. This standard applies to plane secondary enveloping toroidal worm reducers for tire shaping and vulcanizing machines. Series
Single-stage plane double enveloping toroidal worm reducer center distance: 265, 320, 360, 450mm. Two-stage plane double enveloping toroidal worm reducer center distance: 140/280mm. Type
The types of plane double enveloping toroidal worm reducer are shown in Figures 1, 2, 3, 4 and 5. Basic parameters
The basic parameters and main installation dimensions of plane double enveloping toroidal worm reducer should comply with the provisions of Tables 1 and 2. A-direction
(Type I)
1995-07-05 approved by the Ministry of Chemical Industry of the People's Republic of China standard specification network m
All kinds of standard wet industry information free download
1996-03-01 implementation
273895
(Type I)
(Ear type)
Standard implementation network.mm.ba80vccHG/T2738-95||tt| |(v type)
(V type)
Standard heating network mm.baeo
.All kinds of standard industry information are free to download
Center distance
Worm indexing
Circular diameter
HG/T2738-95
Single-stage reducer
Reducer motor
*Special motor for tire shaping vulcanizer (model is JQLX or JZ2-H). L
Table 2 Two-stage reducer
First stage transmission
Second stage transmission
Reducer
Inch, mm
Main installation
212.5212.5320320
2612732
Standard Download Network mmba8080oca Various standards Industry information Free download Reducer
Center distance a
140/280
140/280
Additional instructions:
Transmission ratio
HG/T2738—95
Appendix A
Applicable tire shaping and vulcanizing press for speed reducer
(reference part)
For wheel Tire shaping and thinning machine
mm(in)
910(36)
1030(40.5)
1170(46)
1050(42)
1170(46)
1170(46)
1310(55)bzxZ.net
1525(6 3.5)
1900(75)
1400(55)
2160(85)
2500(100)
2500(100)
1525(63.5)
1525(63.5)
This standard is proposed by China National Chemical Equipment Corporation. Maximum clamping force
1030(105)
1330(135)
1716(175)
1370(140)
1960(200)
2160(220)
2890(295)
4220(4 30)
6470( 660)
2940(300)
8430(850)
(For overturning transmission)
12750(1300)
4220(430)
4220(430)
This standard is under the jurisdiction of the Rubber Machinery Standardization Technical Committee of the National Rubber and Plastic Machinery Standardization Technical Committee. This standard was drafted by the Beijing Rubber Industry Research and Design Institute. The main drafter of this standard is Lai Weihu.
The original Chemical Industry Ministry Standard HG5-1614-86 will be invalid from the date of implementation of this standard. Standard Control Network m.besoso.ccm5
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.