title>JB/T 10126.2-1999 Transition plates for four-jaw chucks for machine tool fixture parts and components - JB/T 10126.2-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 10126.2-1999 Transition plates for four-jaw chucks for machine tool fixture parts and components
JB/T 10126.2-1999 Transition plates for four-jaw chucks for machine tool fixture parts and components

Basic Information

Standard ID: JB/T 10126.2-1999

Standard Name: Transition plates for four-jaw chucks for machine tool fixture parts and components

Chinese Name: 机床夹具零件及部件 四爪卡盘用过渡盘

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-08-06

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)

Standard Classification Number:Machinery>>Process Equipment>>J44 General Fixture

associated standards

alternative situation:Original standard number GB/T 12892-1991

Publication information

other information

Focal point unit:Mechanical Science Research Institute

Publishing department:Mechanical Science Research Institute

Introduction to standards:

JB/T 10126.2-1999 This standard specifies the transition plate that is applicable to the C-type and D-type connection methods in GB/T 5900.1~5900.3-1986 "Interchangeability Dimensions of Flange-type Spindle Ends and Faceplates for Machine Tools" and is connected to GB/ 5901.1-1984 "Four-jaw Self-centering Chuck". This standard was first published in 1983 as JB 3401-83 and revised for the first time in 1991 as GB/T 12892-91. JB/T 10126.2-1999 Transition plate for four-jaw chuck of machine tool fixture parts and components JB/T10126.2-1999 Standard download decompression password: www.bzxz.net

Some standard content:

IC5 28.060.41
Mechanical Industry Standard of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06Promulgated
State Machinery Industry Bureau
Implementation on 2000-01-01
Mechanical Industry Standard of the People's Republic of China
Parts and units of jigs and fixtures
The parts ud anitg ofjigs and fixtercsTransitional plate for 4-jaw chackJB/T10126.2-1999
This standard specifies the applicable D type and D type connecting pieces in GB/T5901.1 and connected with GB/T5901.1.
2 Referenced standards
The provisions contained in the following standards become the provisions of this standard through reference in this standard. When this standard is published, the versions shown are effective. The above standards may be revised. Parties using this standard should consider the possibility of using the latest version of the following standards. GB.T 5900.1-5900.3—1986
GB/5901—1984
3 Dimensions
Machine tool flange spindle extension and faceplate 4 interchangeable dimensions 4 original single-acting chuck
The dimensions are as shown in Figure 1, Figure 2 and Table 1, Table 2. AA
Approved by the National Machinery Industry Bureau on August 6, 1999
Wei Ying acid
Implemented on January 1, 2000
Ten axis end codes
Changed size
Limited deviation
JB/T 10126.2-1999
One B United States
Main part code
Chuck point diameter
Basic size
Limited deviation6
Basic size
Light limit deviation
4 Marking
4. Marking examplebzxZ.net
H/T10136.2-1990
F0 052
+0 U2?
Half end number is 6, 200mm heart-shaped connection force type four-claw chuck uses a cover plate: a German plate C6×200JB/110126.2—1999 The spindle end code is, -200. The square four-claw chuck uses a fun plate: a Zi plate 06×200JB/T10126.2—1999328
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.