JB/T 9111-1999 This standard is a revision of ZB J87 004-88 "Self-adhesive label printing machine". During the revision, technical content and editorial adjustments and modifications were made in accordance with relevant regulations. This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of self-adhesive label printing machines. This standard is applicable to the printing, hot stamping, laminating and die-cutting linkage machines of self-adhesive labels. This standard was first issued on June 12, 1988. JB/T 9111-1999 Self-adhesive label printing machine JB/T9111-1999 standard download decompression password: www.bzxz.net

JCS 37. 100. 10
Machinery Industry Standard of the People's Republic of China
JB/T91111999
The self-adhesive label printing machine
Published on 1999-07-12
State Machinery Industry Bureau
2000-01-01 Implementation
JB/T91111999
This standard is a revision of ZBJ8(04-88 "Non-adhesive label printing machine". Compared with ZBJ87(MM-88, this standard has the following major technical changes: Improved the precision of the standard.
The content of "marking, packaging, transportation and storage" has been supplemented as necessary. This standard replaces BJ8004-86 since its implementation. Appendix A and Appendix B of this standard are both appendices of this standard. This standard is proposed and managed by the National Printing Machinery Standardization Technical Committee. The responsible drafting unit is Beijing Printing Machinery Research Institute. The main drafter of the standard is Yan Cai.
This standard was first issued in June 1988
Machinery Industry Standard of the People's Republic of China
Self-adhesive label printing machine
Thr self-dhrsive babel printing nachineJB/T9111-1990
Generation # Z3 J87 IJ4. xx
This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation, etc. of non-stick label printing machines. Explanation:
This standard applies to non-stick label printing, metallization, film reading, and die-cutting machines. 2
Cited standards
The following standards contain the following documents, which constitute the documents of this standard through reference in this standard. When this standard is used, the relevant documents are All versions are valid. All published standards will be revised. All parties using this standard should explore the feasibility of using the latest version of the following standards: GB1911990
GB:T61881986
GB/T9969.1—199B
G13306—1991
G13384992
8714436—1993
H 6530--1492
JE/T 9115-1999
3 Types and basic parameters
Packaging storage and transportation pictorial symbols
Transport packaging receiving and shipping symbols
1 General rules for product instructions
General technical properties of electromechanical product packaging
General rules for product guarantee documents
Printing machine product reverse number reduction method
Flatbed printing machine technical system
3. Product type According to the requirements of use, the paper feeding, printing, paper collection and film can be combined in any order to form a linkage machine.
3.2 To this parameter shall comply with the provisions of the table,
Table | Basic vertical number
Item H Name
Fiber feed length
Indian yellowness
Greek egg width
Printing colors
Longest!
National Standard City Industrial Business 1999-07-12 Approved
35-180
60-220
70~230
180×220
2000-01-01 Implementation
Date Name
Zhan Dayue Ruler (Long×Wing)
Fund 1 Mixed Degree
Push High Brush Speed ​​
JB9111-1999
Failure丨【Finish】
1.3 Product step number and name meet the requirements of JB/T6530. 4 Technical requirements
4. Finished paper force (vertical) registration difference is not more than 0.05imrml. 4.2 The registration error of the printing roller in the moving direction (die direction) shall not exceed 0.05mm4.3 The registration error of the printing shall not exceed n.[0mm, 4.4 The registration error of the printing stroke shall not be less than .20mm, 4.5 The uniformity and stability of the single-color pattern printing () 90%: 4.6 The first color pattern printing weight stability deviation (e) 0.06.47 The double-line printing product shall ensure that the dots are clear and not deformed. 4.8 The gold-plated summer shall be in accordance with the regulations of B915,
4. The die stroke shall ensure that the cutting shape is complete and smooth, and no cutting is allowed to damage the paper, 4.10 The surface of the gel film shall not be broken or have obvious air leakage, and the film and paper shall be firmly combined, 4.11 The elasticity shall be less than 85 (AJ
4.12 Shaft and operating parts: The operating temperature rise shall not exceed 35℃. 4.13 Half average release 7. Operating time (MTBF) 37001 2211
[40~160
4.14 The machine is running normally, the stirring and moving mechanism is accurate and flexible, and there is no upper and lower and lower movement. 4.15 The machine's brake mechanism and electrical system work sensitively and safely. There should be a safety brake switch at the door cover of each rubber furnace. Ensure that the machine can stop at any position. 4.16 The lubrication system is stable and the oil circuit is smooth. There is no overflow phenomenon. 4.17 External quality
4.17.1 The non-processed surface of the external surface has no pores, no nodules or depressions. 4.17.2 The external surface is free of rust and silicon. Scratches, 4.17.3 Painted parts should be clean and smooth, color and gloss should be uniform, if art paint is used, the effect should be uniform, the paint should be full, without obvious protruding particles, adhesion, paint should not have defects such as sagging and bubbling. 4.17,4, oil circuit and air outlet should be arranged neatly, 4.18 Product reduction supply specification:
! Label printer:
b) Plate loading:
C) Operation and maintenance tools:
d) Necessary accessories and wearing parts
5 Test method bzxZ.net
5.1 Empty operation test
JB/T 9111—[999
5.1.1 Each product must be tested for idling, high speed continuous feeding 15mm, medium speed continuous feeding 30min, low speed continuous feeding 120min
5.1.2 Check the stability and safety of the machine operation, and make sure it complies with the provisions of 4.14, 4.15, 4.16: 5.2 Product performance test
5.z.1 5% (not less than 2 bamboo shoots) of each batch of products shall be tested for performance. 5.2.2 Test pieces
Daily environment temperature (20±2)℃, relative humidity (60±5)%. The printing speed is 90% of the maximum speed of the machine. Materials: (M) selected (C) color embossing ink, 230mm wide non-seven rubber roll paper, 08-1.2mm thick photosensitive resin bottle, 2nnmm household transparent film, 23mm wide electro-stamping foil, printing, hot stamping, die-cutting size 1 modified Appendix A (standard Appendix Island
5.2.3 When the immediate environmental conditions do not meet the requirements of 5.22, the immediate printing speed shall be The machine is rated at 85% of the maximum speed. 5.2.4 Printing error test
5.2.4.1 The product must be printed in two colors or even in three colors. Take 100 consecutive sheets of the printed product for inspection. The inspection and registration error assessment method is as follows: Appendix B (Standard Annex)
5.2.4.2 The machine negative registration error shall comply with the provisions of 42. 5.2.5 Field printing test
5.2.5. The product must be Conduct a single-color solid printing test, and take 50 consecutive samples from the printed product for inspection. Check the method and assessment method in Appendix B.
5.2.5.2 Qualitative evaluation of printing density uniformity and ink application to meet the requirements of 4.5 and 4.6. 5.2.6 Two-line printing test
5.2.61" products must be subjected to a single-color screen printing test. At least 150 consecutive samples are selected from the printed product for inspection. Take one sample every five samples, and take a total of 10 samples. 5.2. The product 2 screen printing quality shall meet the requirements of 4.7. 5.2. Hot stamping, die cutting and printing registration test 5.2.7 The product shall be tested for hot stamping and printing registration and printing and die cutting registration. 100 consecutive samples shall be collected from the printed products for inspection. The inspection method and registration error assessment method shall be in accordance with Appendix R. 5.2.7.2 The registration error shall meet the requirements of 4.3 and 4.4. 5. 2.8 Film test
Use self-adhesive transparent thin film to print products. The film quality should meet the requirements of 4.10. 5.3 Noise measurement
Use a sound level meter to measure during the performance test. The height of the measuring point is half of the sum of the machine height and 1m. The individual points are 1m apart and distributed on the symmetrical center line of the machine. The arithmetic average of the five measured values ​​is the machine noise, which meets the requirements of 1.11.
JB/T 9111—1999
5.4 Use a thermometer to measure the working temperature of the machine bearings and moving parts, and calculate its temperature rise, which should comply with the provisions of 4.12. 5.5 Check the appearance of the product and see if it meets the provisions of 4.17. Inspection rules
6.1 Factory inspection
Each product shall be inspected in accordance with the provisions of 5.1, 5.4 and 5.5, and each batch of products shall be inspected in accordance with the provisions of 5.2.
When there are major changes in product design, process, materials, etc. or new product identification: Test according to the contents specified in this standard. 6.3 If one item of product inspection is qualified, double sampling shall be carried out. If it is still unqualified, the batch of products shall be fully inspected. 6.4 Products shall not be allowed to leave the factory until they are qualified according to the provisions of the standard.
7.1 Each product shall have a label in a conspicuous position. The size of the label shall comply with the provisions of GB13306, and its content shall include: a! b) Product model, name: c) Product key information: d) Manufacturing date (or serial number) or production number 7.2 Product storage and transportation markings shall be selected in accordance with the relevant provisions of GB191. The lifting center of the package that is obviously deviated from the center shall be marked with "lifting" and "center of gravity". 7.3 General transportation packaging and delivery markings shall be in accordance with the relevant provisions of GB: T6388. Packaging, transportation, storage and freezing
8.1 Packaging
8.1.1 Before the product is installed, the exposed surfaces of the parts, spare parts and accessories shall be coated with rust-proof agent, and the surface of the main parts shall also be covered with moisture-proof paper. 8.1.2 The installation of the product shall comply with the relevant provisions of GB/713384. 8.1.3 When each product is shipped, the following documents must be provided: a) Product certificate
The product certificate should be in accordance with the provisions of GBT14436: b) Product instruction manual
The preparation of the product instruction manual should comply with the provisions of GB9969.1: c) Packing list: d) Packing drawing: 8.2 Transportation
When transporting and lifting the product: The markings on the outside of the packaging box must be kept stable and effective, and the product must be kept away from collisions. 8.3 Storage
The product should be placed in a well-ventilated place during storage to avoid moisture. There are measures for outdoor storage. After 2 years of storage, the factory will unpack the product. If the product packaging no longer meets the relevant regulations, it will be repacked. +
A1 four-color printing test version sample
Four-color white. Full-print test version sample see Figure A1
A2 hot stamping version sample
Gold stamping version sample see Figure A2
JB/T 9111-[999
Attached Scene A
(Standard Appendix)
Printing, gilding, die-cutting inspection and adjustment plate samples/15-10
1—solid times: 2—two lines
A1 four-color printing test plate sample
2-core-70
stable device
Figure A2 hot stamping plate support
A3 die-cutting plate sample
For different plate samples, see Figure A43.
E/T911-1999
Figure A3 die Cutting pattern
B1 Registration error
B1.1 Inspection Wanda
JH/T9111-1999
Appendix B
(Appendix of the standard)
Testing and evaluation method of printing quality seal
B1.1.1 The printed lines should be staggered by 0.5~1mm. B1.1.2 Taking the first color as the reference, use a reading sensitive mirror with a graduation value of 0.01mm to check the non-separation between the same side edges in the longitudinal and two directions (8 as shown in Figures 1 and B2. 1
…The first color print line: ·The second color print ruin
91.2 Error evaluation Wanda
According to formula (D1) (B2) calculate the registration error Formula: One sample serial number:
One set of print line end card:
Sample volume:
B? Industry star density uniformity and cover stability B2.1 Use the reverse time model densitometer to measure the solid density value of each point of the printed product (DB2.2 Formula (B3). (H4) Calculate the uniformity of each printed product (J: D
In: Guang Du point number;
Measurement point uniformity
B2.3 According to formula 1B5! Calculate the stability of the original deviation 8
3B9111t999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.