title>JB/T 6447-1992 Technical Specifications for YCJ Series Geared Three-Phase Asynchronous Motors (Frame Size 71 to 280) - JB/T 6447-1992 - Chinese standardNet - bzxz.net
Home > JB > JB/T 6447-1992 Technical Specifications for YCJ Series Geared Three-Phase Asynchronous Motors (Frame Size 71 to 280)
JB/T 6447-1992 Technical Specifications for YCJ Series Geared Three-Phase Asynchronous Motors (Frame Size 71 to 280)

Basic Information

Standard ID: JB/T 6447-1992

Standard Name: Technical Specifications for YCJ Series Geared Three-Phase Asynchronous Motors (Frame Size 71 to 280)

Chinese Name: YCJ 系列齿轮减速三相异步电动机 技术条件( 机座号71~280)

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1992-06-16

Date of Implementation:1993-01-01

standard classification number

Standard Classification Number:Electrical Engineering>>Rotary Motors>>K22 Asynchronous Motors

associated standards

Procurement status:neq IEC 34

Publication information

publishing house:Mechanical Industry Press

Publication date:1993-01-01

other information

drafter:Cheng Huan, Wang Lizhi, Ip Yu-lien, Jin Huasheng, Liu Fugui, Huang Jian

Drafting unit:Boshan Motor Factory and Shanghai Electric Science Research Institute were responsible for drafting, Hefei Motor Factory, Zhejiang Tuyu Motor Factory, Shanghai Wuyi Motor Factory

Focal point unit:Shanghai Electric Science Research Institute, Ministry of Machinery and Electronics Industry

Proposing unit:Shanghai Electric Science Research Institute, Ministry of Machinery and Electronics Industry

Publishing department:Ministry of Machinery Industry of the People's Republic of China

Introduction to standards:

This standard specifies the type, basic parameters and dimensions, technical requirements, test methods and inspection rules of reduction motors, as well as requirements for marking, packaging, warranty period, etc. This standard applies to YCJ series reduction motors with frame sizes of 71 to 280, with motor power of 0.55 to 15kW, output speed of about 15 to 600r/min, and output torque of about 9 to 3,200N·m. The reduction motor adopts external meshing involute cylindrical gears, divided into single-stage, two-stage and three-stage reduction transmission, and can run forward and reverse. JB/T 6447-1992 Technical conditions for YCJ series gear reduction three-phase asynchronous motors (frame sizes 71 to 280) JB/T6447-1992 standard download decompression password: www.bzxz.net

Some standard content:

Mechanical Industry Standard of the People's Republic of China
JB/T6447-1992
Technical Conditions for YCJ Series Gear Reduction Three-Phase Asynchronous Motors
Frame Size 71~280
Published on August 6, 1992
Implementation of the Ministry of Machinery and Electronics Industry of the People's Republic of China on January 1, 1993
Mechanical Industry Standard of the People's Republic of China
Technical Conditions for YCJ Series Gear Reduction Three-Phase Asynchronous Motors
(Frame Size 71~280)
JB/T 6447-1992
YCJ Series Gear Reduction Three-Phase Asynchronous Motors (Frame Size 71~280) (hereinafter referred to as reduction motors) are a derivative series of Y series (IP44) three-phase asynchronous motors. It is formed by coupling a traction motor (hereinafter referred to as motor) with a gear reduction device. 1 Subject content and scope of application
This standard specifies the type, basic parameters and dimensions, technical requirements, test methods and inspection rules of reduction motors, as well as requirements for marking, packaging, warranty period, etc.
This standard applies to YCJ series reduction motors with frame sizes of 71 to 280, with motor power of 0.55 to 15kW, output speed of about 15 to 600r/min, and output torque of about 9 to 3200N·m. The reduction motor adopts external meshing involute cylindrical gears, with single-stage, two-stage and three-stage reduction transmission, and can run forward and reverse. 2 Reference standards
GB4831
Motor product model compilation method
Basic technical requirements for rotary motors
GB1993
-Motor housing protection classification
Motor cooling method
Motor structure and installation type code
GB1096
GB1032
JB/Z294
JB/Z346
G B10069
GB10068
Motor dimensions and tolerancesFrame size 36~400
Type and size of common flat key
Test methods for three-phase asynchronous motors
Motors with flange numbers FF55~FF1080 or FT55~FT1080Test methods for interturn insulation of AC low-voltage motors with scattered windingsTest limits for interturn insulation of AC low-voltage motors with scattered windingsTest methods and limits for noise determination of rotating motors
Vibration measurement method and limit of rotating electrical machines
Packaging, storage and transportation pictorial symbols
ZBK22007
SY1102
GB10095
GB3480
GB3481
Technical conditions for Y series (IP44) three-phase asynchronous motors (frame size 80-315)Hyperbolic gear oil
Precision of involute cylindrical gears
Load bearing capacity of involute cylindrical gears Capacity calculation method Terms, characteristics and causes of gear tooth damage Approved by the Ministry of Machinery and Electronics Industry of the People's Republic of China on August 6, 1992 and implemented on January 1, 1993
3 Type, basic parameters and dimensions
3.1 Model and marking
JB/T6447-1992
3.1.1 Model of reduction motor: composed of product code, frame size, motor rated power and output speed (see GB4831). 3.1.2 Marking example:
Output speed
Motor rated power
Frame size
Product code
3.2 The housing protection level of the reduction motor is IP44 (see GB4942.1). 3.3 The cooling method of the reduction motor is IC0141 (see GB1993). 3.4 The structure and installation type of the reduction motor are IMB3, IMB5, IMB6, IMB7, IMB8, IMV1 and IMV5 (see GB997). 3.5 The rating of the reduction motor is a continuous rating based on the continuous working system (S1). 3.6 The rated frequency, rated voltage, rated power of the motor and its corresponding relationship with the frame number and the wiring method shall comply with the relevant provisions of ZBK22007.
3.7 When the reduction motor is installed in the B3 or B5 type and the use factor KA is 1 (see GB3480), the corresponding relationship between the motor power, output speed and output torque shall comply with the provisions of Table 1. When the B6, B7, B8, V1 or V5 type is used for installation, the output speed value is the same as that in Table 1, and the output torque is allowed to be reduced, but not more than 2%. The speed values ​​not listed in Table 1 can be provided according to the needs of the user within the range of the output speed and torque of the reduction motor. The tolerance of the output speed listed in Table 1 is ±4%. At this time, the corresponding output torque also changes according to the corresponding tolerance. 3.8
The installation dimensions and tolerances of the reduction motor should comply with the provisions of Tables 2 to 6. The overall dimensions should not be greater than those specified in Tables 2 to 6. Table 1
Motor
Output speed
Output torque
Specification code
End cover number
Motor
Output speed
Output torque
End cover number
Specification code
Motor
Output speed
Output torque
JB/T 6447—1992
Continued Table 1
Motor
Specification code
End cover number
Motor
Output speed
Output torque
Motor
End cover number
Specification code
Motor
Output speed
Output torque
JB/T 6447—1992
Continued Table 1
Specification code
100L-6
100L1-4
End cover number
Motor
Output speed
Output torque
Specification code
100L1-4
112M-6
100L2-4
End cover number
Motor
Output speed
Output torque
JB/T 6447—1992
Continued Table 1
End cover number
Specification code
1325-6
112M-4
Motor
Output speed
Output torque
Specification code
112M-4
132M1-6
1325-4
End cover number
Motor
Output speed
Output torque
JB/T 6447—1992
Continued Table 1
Specification code
132S-4
132M2-6
132M-4
End cover number
Motor
Output speed
Output torque
Specification code
160M-4
1601-4
End cover number
Motor
Output speed
Output torque
JB/T 6447—1992
Continued Table 1
Specification code
160L-4
Cover number
Motor
Output speed
Output torque
Specification code
160L-4
End cover number
Note: 1》For the AD, HD, HM and LM dimensions of the motor, see Table 6.2》The position of the K hole is based on the axis of the shaft stop 3》L/dimension is not tested separately·L/+LM is tested 4)GE=DG.GE's pole screen difference is (+℃.20, gear reduction device
JB/T 64471992
Motor
Reduction motor installed with base (single-stage reduction transmission) Table 2
Gear reduction device
JB/T 64471992
Electric motor
Deceleration motor for installation at the bottom (two-stage and three-stage reduction transmission) West 2
160264
2001330
BasicBasic
Note: 1) The AD, HD, HM and LM dimensions of the motor are shown in Table 63)/Dimensions to raise # Consider film, acid (+L4 wheat, etc. 4) GE-DG.The limit deviation of GE is
position
position
external dimension!
360420
ABHDLI
265295
490470465
520525520
Basic
Dimensions
132215
Gear reduction device
JB/T6447-
Motor
Reduction motor for immediate installation (two-stage and three-stage reduction transmission) Table 3Www.bzxZ.net
Note: 1) The AD, HD, HM and LM dimensions of the motor are shown in Table 6. The dimensions are based on the test results.
3) L/D dimensions are not subject to assessment, and are installed as 11+L4. 4) The service tolerance of GE-DG.CE is
In light reduction
JB/T 64471992
Electric motor
Reduction motor with flange installation (single-stage reduction transmission) Figure 3
Production: 1) Motor AD.HD, HM and LMR dimensions are shown in the table 2) S is not inspected and the external dimensions are used as the basis 3) L/dimension is not assessed separately, L/+LM core 4) GE=DG.GE is coded as R!
Inspection degree
Position degree
Overall dimensions
520525520
Production: 1) AD.HD, HM of the motor
2) S has no position degree and is based on the line of the sound god. 3) LI size is not assessed separately, connected to L/+LM
4) The image code of GED-G.GE is
Note: 1) The AD.HD.HM and LMR dimensions of the motor are shown in Table 4) The polarity difference of GE=D=G.GE is
Reduction motor with flange installation (single-stage reduction transmission) Table 4
JB/T 64471992
Supervisory teaching to obtain the installation
Zhongtong machine
Inspection installation Kang
Figure 4 Flange mounted reduction motor (two-reduction and three-reduction transmission) Table 5
+6, 43
In the installation degree
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.