Focal point unit:National Ink Standardization Technical Committee
Proposing unit:China Light Industry Federation
Publishing department:General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
competent authority:China Light Industry Federation
This standard specifies the test method for the initial drying of liquid inks. This standard is applicable to inks with an apparent viscosity range of 0.05Pa·s to 0.25Pa·s (or a viscosity range of 25s to 130s when measured by a No. 4 cup). GB/T 13217.5-2008 Test method for initial drying of liquid inks GB/T13217.5-2008 Standard download decompression password: www.bzxz.net
This standard specifies the test method for the initial drying of liquid inks.
This standard is applicable to inks with an apparent viscosity range of 0.05Pa·s to 0.25Pa·s (or a viscosity range of 25s to 130s when measured by a No. 4 cup).
This standard replaces GB/T13217.5-1991 "Test method for initial drying of gravure plastic inks". || tt|| The main differences between this standard and GB/T13217.5-1991 are as follows:
---The name of the standard is changed to "Test Method for Initial Drying of Liquid Ink";
---The ambient temperature index is adjusted.
This standard is proposed by China Light Industry Federation.
This standard is under the jurisdiction of the National Technical Committee for Ink Standardization.
The drafting units of this standard: Zhejiang Yongzai Chemical Co., Ltd., Yeshi Ink (Zhongshan) Co., Ltd., Hanghua Ink Chemical Co., Ltd., Tianjin Toyo Ink Co., Ltd., Shanghai Modern Environmental Engineering Technology Co., Ltd.
The main drafters of this standard: Wu Min, Wu Shaotang, Huang Ronghai, Zhang Jinmei, Wang Yaming.
The previous versions of the standards replaced by this standard are:
---GB/T13217.5-1991. The clauses in the following documents become the clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties that reach an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version is applicable to this standard.
QB/T1012-1991 Offset Printing Paper
Some standard content:
ICS 87.080 National Standard of the People's Republic of China GB/T 13217.5—2008 Replaces CB/T13217.5-1991 Test nethod for initial dryness of liquid ink Test nethod for initial dryness of liquid inkIssued on 2008-12-30 General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Administration of Standardization of the People's Republic of China Implemented on 2009-09-01 This standard replaces GB/T13217.5-1991 "Test method for initial dryness of plastic gravure ink". The main differences between this standard and GB/T13217.5—1991 are as follows: The name of the standard is changed to "Test method for initial dryness of liquid ink"; The ambient temperature index is adjusted. This standard is proposed by China Federation of Industry and Commerce and is under the jurisdiction of the National Technical Committee for Asphalt Treatment. GB/T 13217.5--2008 The drafting units of this standard are: Zhejiang Yongzai Chemical Co., Ltd., Yeshi Oil (Zhongshan) Co., Ltd., Hanghua Humo Chemical Co., Ltd., Tianjin Dongyang Oil Co., Ltd., and Lhai Modern Environmental Engineering Technology Co., Ltd. The main drafters of this standard are Wu Min, Wu Shaotang, Huang Caiyou, Zhang Taogan, and Mao Yaming. The previous versions of the standard to which this standard refers are: GB/T 13217.5--1991. 1 Scope Test method for initial properties of liquid inks This standard specifies the test method for initial properties of liquid inks. GB/T 13217.5—2008 This standard applies to the eliminators with apparent viscosity in the range of 0.05Fa·s~0.25Pa·s (or the viscosity range of 25s13Cs measured by No. 1 cup). 2 Normative references The clauses in the following documents become the clauses of this standard through reference in this standard. For all references with legal dates, all amendments (excluding errors) or revisions are not applicable to this standard. However, the parties to the agreement based on this standard are encouraged to study whether the latest versions of these documents can be used: For all references without date, the latest versions are applicable to this standard. QB/T1012—1991 Offset printing paper 3 Principle At the specified temperature, temperature and time, the solvent of the ink print is tumbled at a certain speed to make the ink film of different thickness change from liquid to solid, which is the initial flatness, expressed as 30 meters per meter. 4 Tools and Materials 4.1 Scraping paper: 80g/m offset printing paper (in accordance with QB/1012-1991A grade) specification 210mm×70mm, 130mm from the top, with a 2Gmm wide black solid horizontal line, 4.2 Cotton yarn. 4.3 Scrubbing solvent: Use the same series of special solvents for different system liquid inks. 4.4 Adjust the force. 4.5 Stopwatch. Www.bzxZ.net 4.6 Mercury thermometer: temperature range ℃~50℃+division is 0.1℃, 4.7 Meter ruler: minimum scale value is 1mm 4.8 Rubber roller: 932mm, length 100mm, width is 50 degrees. 4. 90 μm-~100 μm Scraper longitudinal instrument. 5 Test conditions 5.1 Test should be conducted under the conditions of temperature (23±2)℃ and humidity (65+5)%. 5.2 Avoid the air outlet during test. 6 Test steps 6.1 Use a scraper to take a certain amount of the scraped sample with a temperature of (23-2)℃ and drop it on the plate at 100m to fill the groove. 6.2 Hold the scraper with both hands and place the scraper vertically and horizontally at the end of the scraper (at the edge of the sample), then move the scraper downward at a high speed to fill the groove with ink, and start the timer. 6.3 Align one end of the sub-sample paper with the zero mark of the scraper, and flatten the scraping sample paper after 30s, push it from the lower end of the scraper to L with a rubber, and then peel off the scraping sample paper vertically. GB/F13217.5—2008
Test results Starting from 0um, use a straight scale to measure the length not marked with ink, expressed in millimeters. 7.1 The test should be carried out in parallel and the measurement error should not exceed 311. The result should be taken as the arithmetic mean. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.