JB/T 2001.3-1999 Types and dimensions of guide bushings for water systems
Basic Information
Standard ID:
JB/T 2001.3-1999
Standard Name: Types and dimensions of guide bushings for water systems
Chinese Name:
水系统 导套 型式与尺寸
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-06-28
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Fluid systems and general parts >> 23.100 Fluid power systems
Standard Classification Number:Machinery>>General Parts>>J20 Hydraulic and Pneumatic Devices
Publication information
other information
Focal point unit:Metallurgical Equipment Standardization Technical Committee
Publishing department:Metallurgical Equipment Standardization Technical Committee
Introduction to standards:
JB/T 2001.3-1999 This standard is a revision of JB 2003-84 "Types and dimensions of guide sleeves for hydraulic presses". This standard specifies the types and dimensions of guide sleeves for hydraulic plunger cylinders. This standard is applicable to guide sleeves for hydraulic plunger cylinders with oil or water as the medium. This standard was first issued on 1984. JB/T 2001.3-1999 Types and dimensions of guide sleeves for water systems JB/T2001.3-1999 Standard download decompression password: www.bzxz.net
Some standard content:
IC.s$ 23.110
Machinery Industry Standard of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
National Machinery Industry Bureau
2(-01-U1 Implementation
Machinery Industry Standard of the People's Republic of China
Water system, guide sleeve type and size
Water systen-Guide hushing-Type ind sizeThis standard specifies the type and size of guide sleeves for use with hydraulic fluids such as water or tears. This standard applies to the type and size of guide sleeves for hydraulic fluids such as hydraulic fluids. 2.1 The type shall be in accordance with the drawing. 2.2 The size shall be in accordance with the specifications in the table in Figure 1. 2031.3.1
JB.T 21.3.2
JBT 2AA1.3.3
JT 1.3 5
JT 1 3 6
J/F2091.37
B/2013
J3/ 2001.39
JD:T 26O1.3.12
IR:T 261.3 13
JB.T 2091.3. [4
P.T2001.315
Approved by State Administration of Machinery Industry on 1999-06-28S
2 ×M4
JBT30013-1999
Original production B2003-E4
2000-01-01 implementation
JB/L 200L.3 to
IB.T 230L.3.1?
JB/23X:1.3.18
JB/T20C 1.3.19
JB/) 20G1.3.21
JB/T 20G1.1.22
J/)Z(KJ13.23
JB 2001.3.24
- 2H11 3.21
JsT 2(001_1.26
JR/T 200I.3.27
B/T2001.3.28
B:T 2001.3.29
iB/T 2001.3:31
JB/T2001.3J2
J3T 2491.3 36
IH/T26.01.3.77
m.T2Go1.3.38
JR.T 2GO1.3.39
J15:2001 3.42
J15/1 2011 1.23
In/T20013.44
JR/T 20013.45
-BT 2001.3.+6
10n..3.47
:B 200:.3.48
iBvT 2001.3.49bzxZ.net
B/T 2 00:.3.51
:IB/T 2001.3.52
JOT 2001.3.14
: JHT:2X1.5.55
: JB-T 2001.3.36
JB/T 2001.5.3?
JRVT 2D1.3.3R
Permitted: DNs 500 m,
Marking example
Using month 11;
Guide sleeve with case diameter of 0 m:
Division 46JT2001.3—999
JE/T20013-1990
Table [(End)
4 ×M12
D50, 118/g
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.