title>Tungsten-Thorium alloy wires - SJ/T 10536.1-1994 - Chinese standardNet - bzxz.net
Home > SJ > Tungsten-Thorium alloy wires
Tungsten-Thorium alloy wires

Basic Information

Standard ID: SJ/T 10536.1-1994

Standard Name:Tungsten-Thorium alloy wires

Chinese Name: 钨钍合金丝

Standard category:Electronic Industry Standard (SJ)

state:in force

Date of Release1994-08-08

Date of Implementation:1994-12-01

standard classification number

Standard Classification Number:General>>Standardization Management and General Provisions>>A01 Technical Management

associated standards

Publication information

other information

Introduction to standards:

SJ/T 10536.1-1994 Tungsten-Thorium Alloy Wire SJ/T10536.1-1994 Standard Download Decompression Password: www.bzxz.net



Some standard content:

Electronic Industry Standard of the People's Republic of China
SJ/T10536.1--94
Tungsten needle alloy wire
1994-08-08 Issued
1994-12-01 Implementation
The Ministry of Electronics Industry of the People's Republic of China Issued Electronic Industry Standard of the People's Republic of China
Tungsten needle alloy wires
Tungsten-thoriumallog wires
Subject Content and Scope of Application
SJ/T10536.1-94
1.1 This standard specifies the technical requirements, test methods, inspection rules, packaging, marking, transportation and storage of tungsten needle alloy wires. 1.2 This standard applies to tungsten needle alloy wires manufactured by powder metallurgy method for electric vacuum devices, electric light sources, etc. (hereinafter referred to as products).
2 Reference standards
GB3312 Determination of dioxide in tungsten needle alloy - Gravimetric method GB4324 Chemical analysis method for tungsten
3 Product classification
3.1 Product naming
The product brand consists of three parts, represented by WThX. WThX
Percentage of dioxidebZxz.net
Chemical element symbol of needle
Chemical element symbol of tungsten
Example: WTh7 means that the content of dioxide in tungsten needle alloy is 0.7%×10%. 3.2 Brand, use, specification
3.2.1 The brand and use of the product shall comply with the provisions of Table 1. Table 1
Manufacture of hooks, springs, high-temperature electrodes, cathodes of gas discharge light sources, etc. for electron tubes. Manufacture of cathodes, grids, high-temperature electrodes, resistant filaments, etc. for electron tubes. Manufacture of cathodes, grids, high-temperature electrodes, resistant filaments, etc. for electron tubes. 2 The specifications of the product shall comply with the provisions of Table 2. 3.2.2
Approved by the Ministry of Electronics Industry of the People's Republic of China on August 8, 1994 and implemented on December 1, 1994
Maximum diameter
Minimum diameter
4 Technical requirements
4.1 Chemical composition
SJ/T10536.1-94
The chemical composition of the product shall comply with the provisions of Table 3. Table 3
4.2 Size
Tungsten content shall not be less than
Needle dioxide content
0.70~0.99
1.00~1.49
1.50~1.99
4.2.1 The allowable deviation of the diameter of the product shall comply with the provisions of Table 5. Table 5
Diameter (d)
150d300
300≤d350
350d500
200mmWire weight deviation
Total content of impurity elements
Not more than
Each impurity element
Content not more than
Diameter deviation
4.2.2Each shaft or roll of product shall be wound with one wire, and its shortest length shall comply with the provisions of Table 6. The number of short wire shafts allowed in each submitted batch shall not exceed 10%. 4.2.3
Diameter (d)
150300
300
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.