JB/T 2756-1993 Carbon slider for trolleybus JB/T2756-1993 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
Carbon Slide Blocks for Trolley Buses
Subject Content and Scope of Application
JB/T275693
Replaces JB2756--81
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of carbon slide blocks for trolley buses.
This standard applies to carbon slide blocks for trolley buses (hereinafter referred to as slide blocks) Reference Standards
GB2828 Batch Inspection Count Sampling Procedure and Sampling Table GB1994 Test Methods for Physical and Chemical Properties of Electric Carbon Products 3 Product Classification
3.1 The classification and model of the slide block shall comply with the provisions of Table 1. Table 1
The structural type and size of the slide block are shown in the figure. 3.2
Note: ① The scale and angle marked in the figure are reference dimensions and are not subject to control inspection items. ③ Slide blocks of other specifications can be produced according to user requirements. Approved by the Ministry of Machinery Industry on August 21, 1993
Classification principles
Hot pressing
Cold pressing
Implementation on October 1, 1993
Technical requirements
The performance of the slider should comply with the provisions of Table 2.
Model numberWww.bzxZ.net
Resistivity
JB/T 2756-93
Shore hardness
Center value
Fluctuation rate%
Flexural strength
4.2 The surface of the slider should be clean and flat, and no oxidation, cracks, or appearance defects such as edge loss, corner loss, and deformation that affect the performance are allowed. 4.3 Impregnation The slider should be impregnated.
4.4 The specifications and dimensions of the slider should comply with the provisions in the figure. 5 Test methods
5.1 The test methods for resistivity, Shore hardness and flexural strength of the slider shall comply with the provisions of GB1994. 5.2 Check the size of the slider with a vernier caliper with an accuracy of 0.02mm and visually inspect the appearance defects. 5.3 After destroying the slider sample, visually inspect the degree of impregnation. 6 Inspection rules
6.1 Carry out factory inspection of the slider in accordance with Articles 4.1 to 4.4 of this standard. 6.2 When inspecting Articles 4.1 to 4.4 of the standard, the sampling method shall comply with GB2828, and the normal inspection secondary sampling plan shall be adopted. The inspection level is the special inspection level S-3, and the qualified quality level AQL=6.5. Marking, packaging, transportation and storage.
7.1 Marking
7.1.1 The packaging box shall be printed with the words moisture-proof and fragile, and the names of the receiving unit, destination, manufacturer and departure station shall be indicated. 7.1.2 After the slider passes the inspection, the manufacturer's quality inspection department will issue a certificate of conformity, which shall indicate: manufacturer name, product name, trademark, model, production batch number, standard code or main performance indicators, full-time inspector code and quality inspection department's special seal of conformity. 7.2 Packaging
7.2.1 First put the slider into a cardboard box, and then put the cardboard box into a wooden packaging box. Fill the gaps in the box with paper scraps or other soft fillers to prevent the slider from moving and colliding.
7.2.2 Each packaging box is accompanied by a product certificate. 7.3 Transportation
The slider should be transported in a sealed or canopy compartment to prevent rain. Be careful when loading and unloading to prevent damage. 7. Exposure Storage
The slider should be stored in a ventilated and clean warehouse to avoid moisture. Additional Notes:
This standard was proposed and managed by Harbin Electric Carbon Research Institute of the Ministry of Machinery Industry. This standard was drafted by Harbin Electric Carbon Factory and Harbin Electric Carbon Research Institute. The drafters of this standard are Lu Xuedong, Wen Donglei and Wang Zhangshan.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.