This standard specifies the technical requirements, test methods, inspection rules, packaging and marking requirements for the national emblem of the People's Republic of China for hanging. This standard applies to national emblems made of aluminum alloy or glass fiber reinforced plastic for hanging. The appearance quality and emblem surface evaluation requirements of national emblems made of other materials must also refer to this standard. GB 15093-1994 National Emblem GB15093-1994 Standard download decompression password: www.bzxz.net
This standard specifies the technical requirements, test methods, inspection rules, packaging and marking requirements for the national emblem of the People's Republic of China for hanging. . This standard applies to national emblems made of aluminum alloy or glass fiber reinforced plastic for hanging. The appearance quality and emblem surface evaluation requirements of national emblems made of other materials must also refer to this standard.

National Standard of the People's Republic of China
国
微
National emblem
1 Subject content and scope of application
GB15093-94
This standard specifies the technical requirements, test methods, inspection rules, packaging and marking requirements of the national emblem of the People's Republic of China for hanging.
This standard is applicable to the national emblem made of aluminum alloy or glass fiber reinforced plastic for hanging. The appearance quality and emblem surface assessment requirements of the national emblem made of other materials must also refer to this standard. 2 Reference standards
GB1449
GB1740
GB1766
GB1771
GB3854
GB6739
GB8545
GB9274
GB9754
Test method for bending properties of glass fiber reinforced plasticsDetermination of moisture and heat resistance of paint films
Rating method for weather resistance of paint films
Determination of salt spray resistance of paint films
Test method for Bacol hardness of fiber reinforced plasticsDetermination of film hardness by pencil method
Dimensional deviation and machining allowance of aluminum and aluminum alloy die forgingsDetermination of resistance of paints and varnishes to liquid media
Determination of specular gloss at 20°, 60° and 85° for paints and varnishes without metallic colorsGB 11186.2
Measurement of coating color Part 2 Measurement of color Measurement of coating color Part 3 Calculation of color difference GB 11186. 3
3 Terminology
3.1 The national emblem red refers to the red color of the emblem surface within a specific red range on the chromaticity diagram. 3.2 The national emblem yellow refers to the yellow color of the emblem surface within a specific yellow range on the chromaticity diagram. 4 Technical requirements
4.1 The shape, pattern, plate positioning and general dimensions of the national emblem surface shall comply with the relevant provisions of the National Emblem Law of the People's Republic of China, the National Emblem Pattern Description of the People's Republic of China (see Appendix A), the National Emblem Pattern Production Description of the People's Republic of China (see Appendix B) and the National Emblem Grid Line Chart of the People's Republic of China.
4.2 The general dimensions and allowable error range of the national emblem are shown in Table 1, Figure 1 and Figure 2. Approved by the State Bureau of Technical Supervision on June 22, 1994 and implemented on October 1, 1994
GB1509394
Figure 1 Coordinate diagram of the dimensions of the national emblem of the People's Republic of China 112
GB15093-94
Figure 2 Grid ink line diagram of the national emblem of the People's Republic of China 145
Item
Horizontal diameter
Overall height
Overall thickness
Distance between the big five-star and the center
Radius of the big five-star
Item
Distance between the two small five-stars and the center
Radius of the small five-star
Distance between the big and small stars
Distance between the small stars Center distance
Width of Dog'an Gate (bottom)
Height of Tian'an Gate (three floors)
Width of wheat ear
Outer diameter of gear
Surface unevenness
Surface non-roundness
Micro bottom surface unevenness
Generation
D
H
T
h
r
ht
r
h2
ha
h.
No.
hs.
B
D
E
s
E
GB15093—9 4
Table 1
600
600±1.7
645±2.0
21±0.4
140±0.9
75±0.4
70±0.6
40±0.3
125±0.9
95±0.7
350±1.3
112±0.7
74±0.6
145±0.9
3
2
3
General dimensions and allowable errors, mm
800
800±2.3
860±2.3
31±0.5
190±1.0
95±0.4
90±0.7
47±0.3
165±0.9
126±0.9
466±1.5
150±0.9
97±0.7
198±1.0
4
2
4
4.3 When national emblems of different sizes are produced due to special needs, they shall be enlarged or reduced in proportion to the general size and allowable error. The chromaticity regulations for the color of the national emblem micro-facet are shown in Table 2. 4.4
Table 2
Material
Aluminum alloy
Glass fiber reinforced plastic
Color name
Red
Yellow
Red
Yellow
Color
Color
Color
Color
Stimulus value Y
%
7.0||t t||36.0
7.5
47.4
0.60
0.40
0.55
0.49
Chromaticity coordinates
y
0.33
0.41
0.34
0.46
4.5The chromaticity data in Table 2 are calculated based on CIE standard illuminant D. and CIE1964 supplementary standard chromaticity system. 4.6 The performance requirements of the national emblem paint film are shown in Table 3. 1000
1000±2.5
1075±2.5
41±0.5
230±1.0
120±0.5
120±0.9
70±0.3
207±1.0
158±0.9|| tt||580±1.7
182±1.0
121±0.9
247±1.0
5
3
5
Allowable errorwww.bzxz.net
AY=±1.0
A2:=±0.01
Ay=±0.01
AY=±1.0||tt| |Ax+0.01
4y=±0.01
AY=±1.0
Az=±0.01
4y±0.01
AY-+1.0
A.:=±0.01
A,y=±0.01
Weather resistance, grade
Gloss (60°)
Adhesion, grade| |tt||Hardness
Water resistance (24h)
Item
Moisture and heat resistance (7d), level
Salt spray resistance (7d), level
4.7 Material strength:
Item
GB15093
Table 3
4.7.1 The bending strength of glass fiber reinforced plastic shall not be less than 140MPa. 4.7.2 The surface hardness of glass fiber reinforced plastic shall not be less than 30. Drop ball impact strength: The national emblem body shall have no cracks or damage. 4.7.3
4.7.4 Free fall strength: The national emblem micro-body shall have no cracks or damage. 94
index
0~1
standard
not less than 90
door
not less than 2R
no blistering or falling off
1
1
The evaluation of the national emblem surface is based on the degree of influence on the appearance quality of the national emblem, and the inspection is carried out on each emblem (see Table 4). 4.8
Table 4
Item
Micro-surface appearance
Embrane red
Embrane yellow
Embrane color difference
5Test method
Requirements
Surface pattern is clear, particles are full, and there shall be no shrinkage, thermal cracking, cold cracking, deformation, edge gap, broken edge, and defects such as sand, impurities, and pores that obviously affect the appearance
No obvious stains, color matching, color collapse, etc. are allowed. No obvious stains, color matching, color collapse, etc. are allowed. Must comply with the provisions of 4.4
5.1. The general dimensions and allowable errors of Guowei are measured with steel rulers and square rulers with an accuracy of 1mm. 5.2 Colorimetry measurement shall be carried out in accordance with the provisions of GB11186.2. 5.3 The performance of the emblem surface paint film shall be measured according to the regulations in GB1766, GB9754.GB6739, GB9274, GB1740 and GB1771. 5.4 Strength test:
5.4.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB1449. 5.4.2 Falling ball impact: Place the national emblem face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, drop the steel ball freely to the center of the emblem surface, and impact it three times repeatedly. Observe whether there are cracks, delamination, etc. on the surface of the sample. 5.4.3 Drop test: Hang the Guowei sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the hardness of the national emblem made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 Unevenness test;
Place the national emblem horizontally on a platform or glass plate, measure the gap between the periphery of the national emblem and the plane, and the result is the bottom surface unevenness 6 Inspection Rules
6.1 General dimensions, emblem Surface evaluation, color and other quality inspections are factory inspections. When materials, formulas, and processes change, type inspection should be carried out. Type inspection is a comprehensive inspection of technical requirements. 62 During the factory inspection, if all inspection items of each product are qualified, it will be judged as passing the inspection, and the batch of products will be qualified. Unqualified products are not allowed to leave the factory or circulate in the market. During the type inspection of GB15093-94
, if all inspection items of the product are qualified, it will be judged as qualified and formal production is allowed. 7 logo, packaging
7.1 logo
The manufacturer and serial number are marked on the back of each logo. 7.2 Packaging
7.2.1 Single package must be convenient for transportation and storage. 7.2.2 There should be a certificate of conformity inside the packaging box. The certificate indicates the serial number, date of manufacture, and storage instructions. It also includes the necessary accessories for installation, the name of the manufacturer, the address, and the name (or code) of the inspector. 8 According to the provisions of the "National Emblem Law of the People's Republic of China", the national emblem production factory is designated by the state, and the standardization administrative department of the State Council is responsible for the supervision and implementation.
GB15093-94
Appendix A|| tt | Ears of wheat and rice symbolize the Chinese people's new democratic revolutionary struggle since the "May 4th" movement and the birth of the new China under the people's democratic dictatorship based on the alliance of workers and peasants led by the working class ★
MI||tt. ||GB15093—94
Appendix B
(supplement)
Instructions for the production of the National Emblem of the People's Republic of China
(General Office of the Central People's Government Committee on September 20, 1950 Announcement), the two wheat jis form a perfect circular ring. The gears are installed at the intersection of the miji poles below. The red ribbons are intertwined with each other and hang down to the left and right, dividing the gears into upper and lower parts. 2. Draw a straight line vertically from the center of the pattern, and the left and right parts of the pattern are completely symmetrical. 3. The position and size of each part of the pattern can be enlarged or reduced according to the proportion of the square ink line drawing. 4. If making a relief, each part should be enlarged or reduced. The height of the parts can be enlarged or reduced according to the proportion of the cross-section diagram. 5. The colors of the national emblem are gold and red: the wheat and rice, the five stars, Tiananmen, and the gear are gold, and the base and hanging ribbon in the ring are red; It is red (the same as the national flag), and the gold is red gold (light and shiny gold)
Zheng
Additional note:
This standard is administered by the Standing Committee of the National People's Congress. This standard is proposed by the Secretariat of the General Office of the State Council and the State Technical Supervision Bureau. The main drafters of this standard are Sun Xiuru, Xue Zhijian, Lin Zhiding, Yu Wanshun, and Yu Shengli. Han Renkai.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.