This standard specifies the outer dimensions and mass limits of transport packages for transport by road, rail, water and air. This standard applies to the design and transportation of transport packages for road, rail, water and air transport. GB/T 16471-2008 Dimensions and mass limits of transport packages GB/T16471-2008 Standard download decompression password: www.bzxz.net
This standard specifies the outer dimensions and mass limits of transport packages for transport by road, rail, water and air transport. This standard applies to the design and transportation of transport packages for road, rail, water and air transport.
This standard replaces GB/T16471-1996 "Dimension Limits of Transport Packages" and GB/T18923-2002 "Mass Limits of Transport Packages".
Compared with GB/T16471-1996 and GB/T18923-2002, the main changes of this standard are as follows:
--- The definition chapter has been deleted;
--- The general requirements and specific requirements are directly stated (see Chapter 3 and Chapter 4);
--- The contents of the standard have been adjusted accordingly according to the current situation (see Chapter 3, Chapter 4 and Appendix A, Appendix B, Appendix C, Appendix D).
Appendix A, Appendix B, Appendix C, and Appendix D of this standard are all informative appendices.
This standard is proposed by the Standardization Administration of China. This standard
is under the jurisdiction of the National Technical Committee for Packaging Standardization (SAC/TC49).
The drafting units of this standard are: the Scientific Research Institute of the Ministry of Transport, the Standard and Metrology Institute of the Ministry of Railways, the Aviation Safety Technology Center of the Civil Aviation Administration of China, the China Packaging Federation, and the Mechanical Science Research Institute.
The main drafters of this standard are: Xiong Caiqi, Wang Wei, Zhang Jin, Qing Hongyu, Wang Li, Huang Xue.
The previous versions of the standards replaced by this standard are:
---GB/T16471-1996;
---GB/T18923-2002.
GB/T1413 Series 1 Classification, dimensions and rated masses of containers (GB/T1413-1998, idtISO668:1995)
Foreword III
1 Scope 1
2 Normative references 1
3 General requirements 1
4 Specific requirements 1
Appendix A (Informative Appendix) Internal dimensions and rated loads of commonly used road freight cars 4
Appendix B (Informative Appendix) Internal dimensions and rated loads of commonly used railway freight cars 6
Appendix C (Informative Appendix) Dimensions and unit area loads of commonly used cargo ships on waterways 10
Appendix D (Informative Appendix) Maximum total height of cargo on commonly used pallet models 13

ICS55.020
National Standard of the People's Republic of China
GB/T16471-—2008
Replaces GB/T16471-1996GB/T18923-2002Dimensional and weight constraints for transport packageReleased on 2008-02-01
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
Implementation on 2008-07-01
Normative references
General requirements
4 Specific requirements
Appendix A (Informative Appendix)
Appendix B (Informative Appendix)
Appendix C (Informative Appendix)
Appendix D (Informative Appendix)
Interior dimensions and rated load of common freight cars on highwaysInterior dimensions and rated load of common freight cars on railwaysDimensions and load per unit area of ​​common cargo ships on waterwaysMaximum total height of cargo on common aircraft types
++-+++++ +.
GB/T16471—2008
GB/T16471—2008
This standard replaces GB/T16471—-1996 <Dimension Limits for Transport Packages> and GB/T18923—2002 <Mass Limits for Transport Packages>.
Compared with GB/T16471-1996 and GB/T18923-2002, the main changes of this standard are as follows: the "Definition" chapter has been deleted;
The "General Requirements" and "Specific Requirements" (see Chapter 3 and Chapter 4) are directly stated: the content of the standard has been adjusted accordingly according to the existing situation (see Chapter 3, Chapter 4 and Appendix A, Appendix B, Appendix C, Appendix D).
Appendix A, Appendix B, Appendix C, and Appendix D of this standard are all informative appendices. This standard is proposed by the Standardization Administration of China. This standard is under the jurisdiction of the National Technical Committee for Packaging Standardization (SAC/TC49). The drafting units of this standard are: the Scientific Research Institute of the Ministry of Transport, the Standard and Metrology Institute of the Ministry of Railways, the Aviation Safety Technology Center of the Civil Aviation Administration of China, the China Packaging Federation, and the Mechanical Science Research Institute. The main drafters of this standard are: Xiong Caiqi, Wang Wei, Zhang Jin, Qing Hongyu, Zhu Li, and Huang Xue. The standards replaced by this standard The previous versions are as follows: GB/T16471-1996;
GB/T189232002.
1 Scope
Dimensions and mass limits of transport packages
GB/T16471--2008
This standard specifies the outer dimensions and mass limits of transport packages transported by road, rail, water and air. This standard applies to the design and transportation of transport packages transported by road, rail, water and air. 2 Normative references
The clauses in the following documents become clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties that reach an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this standard. GB/T1413 series 1 Classification, dimensions and rated mass of containers (GB/T1413-1998, idtISO668:1995) 3 General requirements
The maximum length, width and height of transport packages used for road, rail, water and air transport should not exceed the transportable dimensions of the corresponding transport vehicles, and the maximum mass should not exceed its maximum load. 4 Specific requirements
4.1 Road transport
4.1.1 When the length, width and height of the transport package are less than 3360mm, 1600mm and 1650mm respectively and the mass is not more than 3000kg, it is applicable to the various vehicle types in Table 1 for transportation
4.1.2 When the vehicle type in Table 1 is used, the dimensions and mass of the transport package should be less than the minimum loadable space length, width, height and rated load of the vehicle compartment of the vehicle type, and the maximum dimensions and mass should be less than the maximum loadable space length, width, height and rated load of the vehicle compartment of the vehicle type, the internal dimensions and rated load of the vehicle compartment of the common road trucks, respectively. The rated load range is shown in Table 1. The internal dimensions and rated load of common road truck compartments are shown in Appendix A.
Table 1 Internal dimensions and rated load range of common road truck compartments Model
Shen type truck
Heavy truck
Side truck
Van trailer
Width/mm
380012160
6900121422200||t t||4.2 Railway transport
Height/mm
Door width/mm
Door width/mm
Loading surface above ground
Height/tnm
Rated load
Quantity/kg
4.2.1 When the length, width and height of the transport package are less than 2400mm, 1800mm.2542mm respectively, and the mass is not more than 50000kg, it is applicable to the various types of transport in Table 2.
4.2.2 When the loose car and flat car models in Table 2 are used, the size and mass of the transport package should be less than the minimum loadable space length, width, height and rated load of the car of this model, and the maximum size and mass should be less than the maximum loadable space length, width, height and rated load of the car of this model. When using a boxcar, the size of the transport package should be smaller than the minimum inner width, door width, and door height of the car, and the maximum size should be smaller than the maximum inner width, door width, and door height of the car. The internal dimensions and rated load range of commonly used railway freight cars are shown in Table 2. The internal dimensions and rated load range of commonly used railway freight cars are shown in Appendix B.
Table 2 Internal dimensions and rated load range of commonly used railway freight car compartments Length/mm
1030013000
Width/mm
10560619102400
Long and large freight car
4.3 Water transport
Height/mm
Door width/mm
Door height/mm
Bearing surface to rail surface
Height/mm
Rated load/t
When the mass per square meter of the bottom surface is less than 4.250mm, 3.740mm.1100mm and is not greater than the length and width of the transport package
500kg, it is applicable to Table 3
Ship transportation shop! 4.3.2 The dimensions and unit area mass of the transport package shall be respectively the weight, the maximum dimensions and unit area mass of the cargo hold of ships commonly used for water transport and the minimum length, width, height and unit area mass of the cargo hold of the ship commonly used for air transport. The maximum mass of the cargo area should be less than the # and the weight per unit area should be as shown in the attached table 3. The range of cargo hold dimensions and load per unit area of ​​commonly used waterway ships is as shown in Table 3. When transporting packages (empty container mass), it is applicable to various aviation containers with a length of 740 mm and a height of less than 109 mm respectively. The maximum mass should not be greater than 13608 mm. The weight per unit area should not be greater than the pallet (net mass).
Full internal height
Single vertical load/ckg/m*)
134mm.1.600mmMass not more than)225kg (including container058mm.2
995am (including container board thickness),
The size of the inserted package in the container should not be larger than the container and the container reported cargo size, commonly used container 4.4.3 The sum of the maximum masses of different containers or pallets (including pallets and nets) and cargo should not be greater than the total mass specified in Table 4 or Table 5. The maximum total height of cargo on pallets of commonly used models is shown in Appendix D. Table 4
DPE/DPA
AKE/AKN
ALP/DLP
ALF/AWA
AAP/AA2/AAK
ALE/DQF/ALF
AMA/AQ6/AMK
Length/mm
Common aviation container cargo dimensions and total massWidth/mm
Height/mm
Mass/kg
PAG/PIP
PBJ/P2P
PLA/PLB
PMC/P6P
PRA/P4 AwwW.bzxz.Net
PGE/PTE
FQA/PPC
Table 5 Common cutting dimensions and gross mass of aviation pallets Floor length/mm
4.5 Container transport (except air transport) Floor width/mm
Maximum loading height/mm
GB/T16471—-2008
Gross mass/kg
4.5.1 When the length, width and height of the transport package are less than 2802mm, 2286mm and 2134mm respectively and the mass is not more than 10160kg (including the empty mass of 1D series container), it is applicable to various container transports in GB/T1413. 4.5.2 The maximum length, width and height of the transport package should be less than 11998mm, 2286mm and 2566mm respectively, and the maximum mass should be no more than 30480kg (including the empty mass of 1A series containers in GB/T1413). 4.5.3 The dimensions of transport packages of different container types should be no greater than the cargo dimensions of the container, and the mass should be no greater than the rated mass of the container type (including the empty mass). See GB/T1413 for container dimensions and rated masses. GB/T16471—2008
CA1091
Appendix A
(Informative Appendix)
Table A1 of the internal dimensions and rated load of common road freight cars
Table A1 of the internal dimensions and rated load of common road freight cars Length/mm
CA1092PK2L2
CA1092PK2L3
CA1092PK2L4
CAI111K2P
CAI11IK2PLI
CA1111K2PL2
EQI1 16G | | tt | | EQL116G18D | 3090K
NJD1100DK
NJD1112DP
NJDI3DP
Gil 130
IFW50L
Nissan Japan
CQ 1260.01
CQ19210
CQ30290
Width/mm
Height/mm
Door width/mm
Door height/mm
Bearing surface from ground
Height/mm
Rated load
Quantity/kg
Goose hanging
EQ140SA
Jiexiao 141
Nanjing Dongfeng
NJT5110XLD
NJT5113XLD
Wuhan Dongfeng extended
SG50 60
Length/mm
Table A1 (continued)
Width/mm
Height/mm
Door width/mm
Door height/mm
GB/T16471—2008
Loading surface above ground
Height/mm
Rated load
Quantity/kg
GB/T16471-2008
(Informative Appendix)
Internal dimensions and rated load of commonly used railway freight carsTable B.1
Internal dimensions and rated load of commonly used railway freight carsLength /mm
15:400
Width/mm
Height/mm
Door width/mm
Door height/mm
Bearing surface to ballast surface
Height/mm
Rated heavier
Cgaa/CatB
CSZA-K/CHAK
CHzA-T/CAAT
Cro/Crok
Cga/CaoH
Cama/CaAH
Caon/CabBi
Length/rmrn||t t||12277/12074
Table B.1 (continued)
Width/mmHeight/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to rail surface
Height/mm
2187 Middle part 950
1294 Middle part 736
1090 External part 630
Rated load
GB/T16471—2008
230t Drop hole
350t Drop hole
Length /mm
1690-0
Table B.1 (continued)
Width/mm
630
Height/mm
Gate width/mm
Gate height/mm
Bearing surface to rail surface
Height/mm
1400 Middle part 835
1259 Middle part 777
1350 Middle part 777
1.707 Middle part 850
2150 Middle part 800
2259 Middle part 930
Upper plane empty car 1150||tt| |2730 Middle part 1160
Middle part 1150
1225 Middle part 1275
1135.5 Middle part 578.5
3060 Middle part 3100
Rated load
P62(N)
Length/mm
Table B.1 (continued)
Width/mm
Commodity/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to soft surface
Height/mm
Rated cutting weight3 The dimensions of different types of transport packages should not be greater than the cargo dimensions of the container, and the mass should not be greater than the rated mass of the container (including the mass of the empty container). For container dimensions and rated mass, see GB/T1413. GB/T16471—2008
CA1091
Appendix A
(Informative Appendix)
Table A1 of the internal dimensions and rated load of common road truck compartments
Table A1 of the internal dimensions and rated load of common road truck compartments Length/mm
CA1092PK2L2
CA1092PK2L3
CA1092PK2L4
CAI111K2P
CAI11IK2PLI
CA1111K2PL2
EQI1 16G | | tt | | EQL116G18D | 3090K
NJD1100DK
NJD1112DP
NJDI3DP
Gil 130
IFW50L
Nissan Japan
CQ 1260.01
CQ19210
CQ30290
Width/mm
Height/mm
Door width/mm
Door height/mm
Bearing surface from ground
Height/mm
Rated load
Quantity/kg
Goose hanging
EQ140SA
Jiexiao 141
Nanjing Dongfeng
NJT5110XLD
NJT5113XLD
Wuhan Dongfeng extended
SG50 60
Length/mm
Table A1 (continued)
Width/mm
Height/mm
Door width/mm
Door height/mm
GB/T16471—2008
Loading surface above ground
Height/mm
Rated load
Quantity/kg
GB/T16471-2008
(Informative Appendix)
Internal dimensions and rated load of commonly used railway freight carsTable B.1
Internal dimensions and rated load of commonly used railway freight carsLength /mm
15:400
Width/mm
Height/mm
Door width/mm
Door height/mm
Bearing surface to ballast surface
Height/mm
Rated heavier
Cgaa/CatB
CSZA-K/CHAK
CHzA-T/CAAT
Cro/Crok
Cga/CaoH
Cama/CaAH
Caon/CabBi
Length/rmrn||t t||12277/12074
Table B.1 (continued)
Width/mmHeight/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to rail surface
Height/mm
2187 Middle part 950
1294 Middle part 736
1090 External part 630
Rated load
GB/T16471—2008
230t Drop hole
350t Drop hole
Length /mm
1690-0
Table B.1 (continued)
Width/mm
630
Height/mm
Gate width/mm
Gate height/mm
Bearing surface to rail surface
Height/mm
1400 Middle part 835
1259 Middle part 777
1350 Middle part 777
1.707 Middle part 850
2150 Middle part 800
2259 Middle part 930
Upper plane empty car 1150||tt| |2730 Middle part 1160
Middle part 1150
1225 Middle part 1275
1135.5 Middle part 578.5
3060 Middle part 3100
Rated load
P62(N)
Length/mm
Table B.1 (continued)
Width/mm
Commodity/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to soft surface
Height/mm
Rated cutting weight3 The dimensions of different types of transport packages should not be greater than the cargo dimensions of the container, and the mass should not be greater than the rated mass of the container (including the mass of the empty container). For container dimensions and rated mass, see GB/T1413. GB/T16471—2008
CA1091
Appendix A
(Informative Appendix)
Table A1 of the internal dimensions and rated load of common road truck compartments
Table A1 of the internal dimensions and rated load of common road truck compartments Length/mm
CA1092PK2L2
CA1092PK2L3
CA1092PK2L4
CAI111K2P
CAI11IK2PLI
CA1111K2PL2
EQI1 16G | | tt | | EQL116G18D | 3090K
NJD1100DK
NJD1112DP
NJDI3DP
Gil 130
IFW50L
Nissan Japan
CQ 1260.01
CQ19210
CQ30290
Width/mm
Height/mm
Door width/mm
Door height/mm
Bearing surface from ground
Height/mm
Rated load
Quantity/kg
Goose hanging
EQ140SA
Jiexiao 141
Nanjing Dongfeng
NJT5110XLD
NJT5113XLD
Wuhan Dongfeng extended
SG50 60
Length/mm
Table A1 (continued)
Width/mm
Height/mm
Door width/mm
Door height/mm
GB/T16471—2008
Loading surface above ground
Height/mm
Rated load
Quantity/kg
GB/T16471-2008
(Informative Appendix)
Internal dimensions and rated load of commonly used railway freight carsTable B.1
Internal dimensions and rated load of commonly used railway freight carsLength /mm
15:400
Width/mm
Height/mm
Door width/mm
Door height/mm
Bearing surface to ballast surface
Height/mm
Rated heavier
Cgaa/CatB
CSZA-K/CHAK
CHzA-T/CAAT
Cro/Crok
Cga/CaoH
Cama/CaAH
Caon/CabBi
Length/rmrn||t t||12277/12074
Table B.1 (continued)
Width/mmHeight/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to rail surface
Height/mm
2187 Middle part 950
1294 Middle part 736
1090 External part 630
Rated load
GB/T16471—2008
230t Drop hole
350t Drop hole
Length /mm
1690-0
Table B.1 (continued)
Width/mm
630
Height/mm
Gate width/mm
Gate height/mm
Bearing surface to rail surface
Height/mm
1400 Middle part 835
1259 Middle part 777
1350 Middle part 777
1.707 Middle part 850
2150 Middle part 800
2259 Middle part 930
Upper plane empty car 1150||tt| |2730 Middle part 1160
Middle part 1150
1225 Middle part 1275
1135.5 Middle part 578.5
3060 Middle part 3100
Rated load
P62(N)
Length/mm
Table B.1 (continued)
Width/mm
Commodity/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to soft surface
Height/mm
Rated cutting weight1 (continued)
Width/mm
630
Height/mm
Gate width/mm
Gate height/mm
Bearing surface to rail surface
Height/mm
1400Middle 835
1259Middle 777
1350Middle 777
1.707Middle 850
2150Middle 800
2259Middle 930
Upper plane empty car 1150
2730Middle 1160| |tt||Middle part 1150
1225Middle part 1275
1135.5Middle part 578.5
3060Middle part 3100
Rated load
P62(N)
Length/mm
Table B.1 (continued)
Width/mm
Commodity/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to soft surface
Height/mm
Rated cutting weight1 (continued)
Width/mm
630
Height/mm
Gate width/mm
Gate height/mm
Bearing surface to rail surface
Height/mm
1400Middle 835
1259Middle 777
1350Middle 777
1.707Middle 850
2150Middle 800
2259Middle 930
Upper plane empty car 1150
2730Middle 1160| |tt||Middle part 1150
1225Middle part 1275
1135.5Middle part 578.5
3060Middle part 3100
Rated load
P62(N)
Length/mm
Table B.1 (continued)
Width/mm
Commodity/mm
Door width/mm
Door height/mm
GB/T16471—2008
Bearing surface to soft surface
Height/mm
Rated cutting weight
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.